Siemens SINAMICS G120C Getting Started page 57

p8924 PN DHCP mode
p8925 PN interfaces configuration
0: No function
1: Activate the configuration
2: Activate the configuration and save
3: Delete configuration
p8929 PN Remote Controller number
0: Automation or Safety
1: Automation and Safety
r8930 PN Name of Station active
r8931 PN IP Address of Station active
r8932 PN Default Gateway of Station active
r8933 PN Subnet Mask of Station active
r8934 PN DHCP mode active
r8935 PN MAC Address of Station
r8939 PN DAP ID
r8960 PN Subslot assignment
r8961 PN IP Addr Remote Controller 1
r8962 PN IP Addr Remote Controller 2
p8980 Ethernet/IP profile
0: SINAMICS
p8981 Ethernet/IP ODVA STOP mode
0: OFF1
p8982 Ethernet/IP ODVA speed (p8982) or torque
(p8983) scaling
p8983
123: 32
125: 8
127: 2
129: 0,5
131: 0,125
133: 0,03128
p8991 USB memory access
p9400 Safely remove memory card
0 No memory card inserted
1 Memory card inserted
2 Request "safe removal" of the memory
card
3 "Safe removal" possible
100 "Safe removal" not possible due to access
r9401 Safely remove memory card status
r9463 Set valid macro
p9484 BICO interconnections, search signal source
SINAMICS G120C converter
Getting Started, 04/2014, FW V4.7, A5E34264105B AA
1: ODVA / AC/DC
1: OFF2
124: 16
126: 4
128: 1
130: 0,25
132: 0,0625
4.2 Commissioning with BOP-2 operator panel
r9485 BICO interconnections, search signal source
number
r9486 BICO interconnections, search signal source first
index
p9601 SI enable, functions integrated in the drive
(processor 1)
p9610 SI PROFIsafe address (processor 1)
p9650 SI F-DI changeover, tolerance time (processor 1)
[ms]
p9651 SI STO debounce time (processor 1) [ms]
p9659 SI forced checking procedure timer [h]
r9660 SI forced checking procedure remaining time [h]
r9670 SI module identifier, Control Unit
r9672 SI module identifier, Power Module
p9700 SI copy function
p9701 Acknowledge SI data change
p9761 SI password input [hex]
p9762 SI password new [hex]
p9763 SI password acknowledgment [hex]
r9768 SI PROFIsafe control words received (processor
1)
[0] PZD 1
r9769 SI PROFIsafe status words send (processor 1)
[0] PZD 1
r9770 SI version, safety functions integrated in the drive
(processor 1)
r9771 SI common functions (processor 1)
r9772 CO/BO: SI status (processor 1)
r9773 CO/BO: SI status (processor 1 + processor 2)
r9776 SI diagnostics
.00 1 = safety parameters changed, POWER
ON required
.01 1 = safety functions enabled
.02 1 = safety components exchanged and
save necessary
r9780 SI monitoring clock cycle (processor 1) [ms]
r9781 SI checksum to check changes (processor 1)
r9782 SI time stamp to check changes (processor 1) [h]
r9794 SI crosswise comparison list (processor 1)
r9795 SI diagnostics, STOP F (processor 1)
r9798 SI actual checksum SI parameters (processor 1)
p9799 SI reference checksum SI parameters (processor
1)
Commissioning
... [7] PZD 8
... [7] PZD 8
57