Siemens SINAMICS G120C Getting Started page 53

r2138 CO/BO: Control word, faults/alarms
r2139 CO/BO: Status word, faults/alarms 1
p2141 Speed threshold value 1 [rpm]
p2153 Speed actual value filter time constant [ms]
p2156 Switch-on delay comparison value reached [ms]
r2169 CO: Speed actual value smoothed signals [rpm]
p2170 Current threshold value [A]
p2171 Current threshold value reached delay time [ms]
p2174 Torque threshold value 1 [Nm]
p2194 Torque threshold value 2 [%]
p2195 Torque utilization switch-off delay [ms]
r2197 CO/BO: Status word monitoring functions 1
r2198 CO/BO: Status word monitoring 2
r2199 CO/BO: Status word monitoring 3
p2200 BI: Technology controller enable
p2201 CO: Techn. controller fixed value 1 [100 ≙ 100%]
p2202 CO: Techn. controller fixed value 2 [100 ≙ 100%]
p2203 CO: Techn. controller fixed value 3 [100 ≙ 100%]
p2204 CO: Techn. controller fixed value 4 [100 ≙ 100%]
p2205 CO: Techn. controller fixed value 5 [100 ≙ 100%]
p2206 CO: Techn. controller fixed value 6 [100 ≙ 100%]
p2207 CO: Techn. controller fixed value 7 [100 ≙ 100%]
p2208 CO: Techn. controller fixed value 8 [100 ≙ 100%]
p2209 CO: Techn. controller fixed value 9 [100 ≙ 100%]
p2210 CO: Techn. controller fixed value 10 [100 ≙ 100%]
p2211 CO: Techn. controller fixed value 11 [100 ≙ 100%]
p2212 CO: Techn. controller fixed value 12 [100 ≙ 100%]
p2213 CO: Techn. controller fixed value 13 [100 ≙ 100%]
p2214 CO: Techn. controller fixed value 14 [100 ≙ 100%]
p2215 CO: Techn. controller fixed value 15 [100 ≙ 100%]
p2216 Techn. controller fixed value selection method
0 Fixed value selection direct
1 Fixed value selection binary
p2220 BI: Techn. controller fixed value selection bit 0
p2221 BI: Techn. controller fixed value selection bit 1
p2222 BI: Techn. controller fixed value selection bit 2
p2223 BI: Techn. controller fixed value selection bit 3
r2224 CO: Techn. controller fixed value active [100 ≙
100%]
r2225 CO/BO: Techn. controller fixed value selection
status word
r2229 Techn. controller number currently
SINAMICS G120C converter
Getting Started, 04/2014, FW V4.7, A5E34264105B AA
4.2 Commissioning with BOP-2 operator panel
p2230 Techn. controller motorized potentiometer
configuration
.00 Storage active
.02 Initial rounding active
.03 Non-volatile data save active for
p2230.0 = 1
.04 Ramp-function generator always active
r2231 Techn. controller motorized potentiometer setpoint
memory
p2235 BI: Techn. controller motorized potentiometer
setpoint up
p2236 BI: Techn. controller motorized potentiometer
setpoint down
p2237 Techn. controller motorized potentiometer
maximum value [%]
p2238 Techn. controller motorized potentiometer
minimum value [%]
p2240 Techn. controller motorized potentiometer start
value [%]
r2245 CO: Techn. controller motorized potentiometer
setpoint before RFG [100 ≙ 100%]
p2247 Techn. controller motorized potentiometer ramp-
up time [s]
p2248 Techn. controller motorized potentiometer ramp-
down time [s]
r2250 CO: Techn. controller motorized potentiometer
setpoint after RFG [100 ≙ 100%]
p2251 Techn. controller mode
0 Techn. controller as main speed setpoint
1 Techn. controller as additional speed setpoint
p2253 CI: Techn. controller setpoint 1 [100 ≙ 100%]
p2254 CI: Techn. controller setpoint 2 [100 ≙ 100%]
p2255 Techn. controller setpoint 1 scaling [100 ≙ 100%]
p2256 Techn. controller setpoint 2 scaling [100 ≙ 100%]
p2257 Techn. controller ramp-up time [s]
p2258 Techn. controller ramp-down time [s]
r2260 CO: Techn. controller setpoint after ramp function
generator [100 ≙ 100%]
p2261 Techn. controller setpoint filter time constant [s]
p2263 Techn. controller type
0 D component in the actual value signal
1 D component in the fault signal
p2264 CI: Techn. controller actual value [100 ≙ 100%]
p2265 Techn. controller actual value filter time constant
[s]
r2266 CO: Techn. controller actual value after filter [100
≙ 100%]
Commissioning
53