Siemens SINAMICS G120C Getting Started page 44

Commissioning
4.2 Commissioning with BOP-2 operator panel
No. Description
10 1LE1 standard induction motor
13 1LG6 standard induction motor
17 1LA7 standard induction motor
19 1LA9 standard induction motor
100 1LE1 standard induction motor
p0301 Motor code number selection
p0304 Rated motor voltage [V]
p0305 Rated motor current [A]
p0306 Number of motors connected in parallel
p0307 Rated motor power [kW]
p0308 Rated motor power factor
p0309 Rated motor efficiency [%]
p0310 Rated motor frequency [Hz]
p0311 Rated motor speed [rpm]
p0312 Rated motor torque [Nm]
p0320 Motor rated magnetizing current/short-circuit
current [A]
p0322 Maximum motor speed [rpm]
p0323 Maximum motor current [A]
p0325 Motor pole position identification current 1st
phase [A]
p0329 Motor pole position identification current [A]
r0330 Rated motor slip
r0331 Actual motor magnetizing current/short-circuit
current
r0333 Rated motor torque [Nm]
p0335 Motor cooling type
p0340 Automatic calculation of motor/control parameters
p0341 Motor moment of inertia [kgm²]
p0342 Ratio between the total and motor moment of
inertia [kgm²]
r0345 Nominal motor starting time
p0346 Motor excitation build-up time [s]
p0347 Motor de-excitation time [s]
p0350 Motor stator resistance, cold [Ω]
p0352 Cable resistance [Ω]
r0395 Actual stator resistance
r0396 Actual rotor resistance
p0500 Technology application
p0505 Selecting the system of units
1 System of units SI
44
No. Description
2 Referred system of units/SI
3 US system of units
4 System of units, referred/US
p0573 Inhibit automatic reference value calculation
p0595 Selecting technological units
1 %
3 bar
6 ltr/s
9 m³/min
12 kg/s
15 t/min
18 kN
21 °F
24 gallon/min
27 inch³/h
30 lb/h
33 K
36 m/s
39 BTU/min
42 inch wg
45 % r.h.
p0596 Reference quantity, technological units
p0601 Motor temperature sensor type
0 No sensor
1 PTC warning & timer
2 KTY84
4 Bimetallic NC contact warning & timer
p0604 Motor temperature alarm threshold [°C]
p0605 Motor temperature fault threshold [°C]
p0610 Motor overtemperature response
0 No response, alarm only, no reduction of I
1 Alarm with reduction of I
2 Alarm and fault, no reduction of I
12 Messages, no reduction of I
is saved
p0611 I t motor model thermal time constant [s]
2
p0612 Motor temperature model activation
00 Activate motor
temperature
model 1 (I
Getting Started, 04/2014, FW V4.7, A5E34264105B AA
2 1 referred, no dimensions
4 °C 5 Pa
7 m³/s 8 ltr/min
10 ltr/h 11 m³/h
13 kg/min 14 kg/h
16 t/h 17 N
19 Nm 20 psi
22 gallon/s 23 inch³/s
25 inch³/min 26 gallon/h
28 lb/s 29 lb/min
31 lbf 32 lbf ft
34 rpm 35 parts/min
37 ft³/s 38 ft³/min
40 BTU/h 41 mbar
43 ft wg 44 m wg
46 g/kg
and fault
max
max
, temperature
max
01 Activate motor
temperature model
t) 2
2
SINAMICS G120C converter
max