Siemens SINAMICS G120C Getting Started page 43

No. Description
.13 External fault 1 (F07860)
.15 CDS bit 1
r0056 CO/BO: Status word, closed-loop control
r0060 CO: Speed setpoint before setpoint filter
[100 % ≙ p2000]
r0062 CO: Speed setpoint after filter [100 % ≙ p2000]
r0063 CO: Speed actual value unsmoothed
[100 % ≙ p2000]
r0064 CO: Speed controller system deviation
[100 % ≙ p2000]
r0065 Slip frequency [100 % ≙ p2000]
r0066 CO: Output frequency [100 % ≙ p2000]
r0067 CO: Output current, maximum [100 % ≙ p2002]
r0068 CO: Absolute current actual value unsmoothed
[100 % ≙ p2002]
r0070 CO: Actual DC link voltage [100 % ≙ p2001]
r0071 Maximum output voltage [100 % ≙ p2001]
r0072 CO: Output voltage [100 % ≙ p2001]
r0075 CO: Current setpoint field-generating
[100 % ≙ p2002]
r0076 CO: Current actual value field-generating
[100 % ≙ p2002]
r0077 CO: Current setpoint torque-generating
[100 % ≙ p2002]
r0078 CO: Current actual value torque-generating
[100 % ≙ p2002]
r0079 CO: Torque setpoint, total [100 % ≙ p2003]
r0080 CO: Actual torque value
[0] unsmoothed
r0082 CO: Active power actual value
[0] unsmoothed
[2] Electric power
p0100 IEC/NEMA motor standard
0 IEC motor (50 Hz, SI units)
1 NEMA motor (60 Hz, US units)
2 NEMA motor (60 Hz, SI units)
p0124 CU Identification via LED
p0133 Motor configuration
.00 1: Delta
0: Star
p0170 Number of Command Data Sets (CDS)
p0180 Number of Drive Data Sets (DDS)
SINAMICS G120C converter
Getting Started, 04/2014, FW V4.7, A5E34264105B AA
[1] smoothed
[1] smoothed with
p0045
.01 1: 87 Hz
0: No 87 Hz
4.2 Commissioning with BOP-2 operator panel
No. Description
p0201 Power unit code number
r0204 Power unit, hardware properties
p0205 Power unit application
0 Load cycle with high overload
1 Load cycle with light overload
r0206 Rated power unit power [kw/hp]
r0207 Rated power unit current
r0208 Rated power unit line supply voltage [V]
r0209 Power unit, maximum current
p0210 Drive unit line supply voltage [V]
p0219 Braking resistor braking power [kW]
p0230 Drive filter type, motor side
0 No filter
1 Motor reactor
2 dv/dt filter
3 Siemens sine-wave filter
4 Sine wave filter, third-party manufacturer
p0233 Power unit motor reactor [mH]
p0234 Power unit sine-wave filter capacitance [µF]
r0238 Internal power unit resistance
p0287 Ground fault monitoring thresholds
[100 % ≙ r0209]
r0289 CO: Maximum power unit output current
[100 % ≙ p2002]
p0290 Power unit overload response
0 Reduce output current or output frequency
1 No reduction, shutdown when overload
threshold is reached
2 Reduce I_output or f_output and f_pulse (not
using I2t).
3 Reduce the pulse frequency (not using I2t)
12 I_output or f_output and automatic pulse
frequency reduction
13 Automatic pulse frequency reduction
p0292 Power unit temperature alarm threshold [°C]
p0295 Fan run-on time [s]
p0300 Motor type selection
0 No motor
1 Induction motor
2 Synchronous motor
Commissioning
43