Siemens SINAMICS G120C Getting Started page 48

Commissioning
4.2 Commissioning with BOP-2 operator panel
p1121 Ramp-function generator ramp-down time [s]
p1130 Ramp-function generator initial rounding-off time
[s]
p1131 Ramp-function generator final rounding-off time
[s]
p1134 Ramp-function generator rounding-off type
0 Continuous smoothing
1 Discontinuous smoothing
p1135 OFF3 ramp-down time [s]
p1136 OFF3 initial rounding-off time [s]
p1137 OFF3 final rounding-off time [s]
p1138 CI: Acceleration ramp scaling [100 ≙ 100%]
p1139 CI: Ramp down scaling [100 ≙ 100%]
p1140 BI: Enable ramp-function generator
p1141 BI: Continue ramp-function generator
p1142 BI: Enable speed setpoint
r1149 CO: Ramp-function generator acceleration [100 %
≙ p2007]
r1170 CO: Speed controller setpoint sum
[100 % ≙ p2000]
r1198 CO/BO: Control word, setpoint channel
p1200 Flying restart operating mode
0 Flying restart inactive
1 Flying restart always active (start in setpoint
direction)
4 Flying restart always active (start only in
setpoint direction)
p1201 BI: Flying restart enable signal source
p1202 Flying restart search current [100 % ≙ r0331]
p1203 Flying restart search rate factor [%]
A higher value results in a longer search time.
p1206 Set fault number without automatic restart
p1210 Automatic restart mode
0 Inhibit automatic restart
1 Acknowledge all faults without restarting
4 Restart after line supply failure, without
additional start attempts
6 Restart after fault with additional start
attempts
14 Restart after line supply failure following
manual acknowledgement
16 Restart after fault following manual
acknowledgement
48
26 Acknowledging all faults and restarting for an
ON command
p1211 Automatic restart, start attempts
p1212 Automatic restart, delay time start attempts [s]
p1213 Automatic restart, monitoring time [s]
[0] Restart
p1215 Motor holding brake configuration
0 No motor holding brake being used
3 Motor holding brake like sequential control,
connection via BICO
p1216 Motor holding brake, opening time [ms]
p1217 Motor holding brake, closing time [ms]
p1230 BI: DC braking activation
p1231 DC braking configuration
0 No function
4 DC braking
5 DC braking OFF1/OFF3
14 DC braking below starting speed
p1232 DC braking, braking current [A]
p1233 DC braking time [s]
p1234 Speed at the start of DC braking [rpm]
r1239 CO/BO: DC braking status word
p1240 V controller or V
DC
(vector control)
0 Inhibit V controller
DC
1 Enable V
DC_max
2 Enable V
DC_min
3 Enable V
DC_min
controller
r1242 V controller switch-in level [100 % ≙ p2001]
DC_max
p1243 V controller dynamic factor [%]
DC_max
p1245 V controller switch-in level (kinetic buffering)
DC_min
[%]
r1246 V controller switch-in level (kinetic buffering)
DC_min
[100 % ≙ p2001]
p1247 V controller dynamic factor (kinetic buffering)
DC_min
[%]
p1249 V controller speed threshold [rpm]
DC_max
p1254 V controller automatic ON level detection
DC_max
0 Automatic detection inhibited
1 Automatic detection enabled
p1255 V controller time threshold [s]
DC_min
p1256 V controller response (kinetic buffering)
DC_min
0 Buffer V until undervoltage, n<p1257 →
DC
F07405
Getting Started, 04/2014, FW V4.7, A5E34264105B AA
[1] Reset start counter
monitoring configuration
DC
controller
controller (kinetic buffering)
controller and V
DC_max
SINAMICS G120C converter