Menu 0 - Control Techniques Commander SK Advanced User's Manual

Introduction Parameter x.00
8

Menu 0

Table 8-1 Menu 0 parameters: single line descriptions
Par Description
01 Minimum set speed (Hz)
02 Maximum set speed (Hz)
03 Acceleration rate (s/100Hz)
04 Deceleration rate (s/100Hz)
05 Drive configuration
06 Motor rated current (A)
07 Motor rated speed (rpm)
08 Motor rated voltage (V)
Motor power factor (cos ϕ)
09
10 Parameter access
11 Start/Stop logic select
12 Brake enable
15 Jog reference (Hz)
16 Analog 1 input mode (mA)
17 Enable negative preset speeds
18 Preset speed 1 (Hz)
19 Preset speed 2 (Hz)
20 Preset speed 3 (Hz)
21 Preset speed 4 (Hz)
22 Load display units
23 Speed display units
24 Customer defined scaling
25 Security set up
27 Power up keypad reference
28 Parameter cloning
29 Load defaults
30 Ramp mode
31 Stopping mode
32 Variable torque select
33 Catch a spinning motor select
34 Terminal B7 function select
35 Digital output mode (terminal B3)
36 Analog output mode (terminal B1)
37 Maximum switching frequency (kHz)
38 Autotune
39 Motor rated frequency (Hz)
40 Number of poles
41 Voltage mode selector
42 Low frequency voltage boost (%)
43 Serial comms baud rate
44 Serial address
45 Software version
46 Brake release current threshold (%)
47 Brake applied current threshold (%)
48 Brake release frequency (Hz)
49 Brake applied frequency (Hz)
50 Pre-brake release delay (s)
51 Post brake release delay (s)
52 Fieldbus node address
53 Fieldbus baud rate
54 Fieldbus diagnostics
55 Last trip
56 Trip before Pr 55
16
Parameter Keypad and
description format display
230/400
www.controltechniques.com
User
CT Modbus RTU
programming
Default
Eur USA
0.0
50.0 60.0
5.0
10.0
AI.AV
Drive rating
1500 1800
230/460
0.85
L1
0 4
diS
1.5
4-.20
OFF (0)
0
0
0
0
Ld
Fr
1.000
0
0
no
no
1
0
0
OFF (0)
dig
n=0
Fr
3
0
50.0 60.0
Auto
Ur I
3.0
19.2
1
50
10
1.0
2.0
1.0
1.0
0
0
0
CT Soft Menu 0
Corresponding extended
menu parameter
Pr 1.07
Pr 1.06
Pr 2.11
Pr 2.21
Pr 11.27
Pr 5.07
Pr 5.08
Pr 5.09
Pr 5.10
Pr 11.44
Pr 6.04
Pr 12.41
Pr 1.05
Pr 7.06
Pr 1.10
Pr 1.21
Pr 1.22
Pr 1.23
Pr 1.24
Pr 4.21
Pr 5.34
Pr 11.21
Pr 11.30
Pr 1.51
Pr 11.42
Pr 11.43
Pr 2.04
Pr 6.01
Pr 5.13
Pr 6.09
Pr 8.35
Pr 8.41
Pr 7.33
Pr 5.18
Pr 5.12
Pr 5.06
Pr 5.11
Pr 5.14
Pr 5.15
Pr 11.25
Pr 11.23
Pr 11.29
Pr 12.42
Pr 12.43
Pr 12.44
Pr 12.45
Pr 12.46
Pr 12.47
Pr 15.03
Pr 15.04
Pr 15.06
Pr 10.20
Pr 10.21
Commander SK Advanced User Guide
Advanced parameter
descriptions
Setting
Issue Number: 2