Major Components And Accessories - Zip HydroTap G4 Celsius Installation Instructions Manual

Parts supplied
Tap options
Command-Centre
QUICK START GUIDE STEP 1-
Prepare and fit the Taps
HydroTap Tap All-In-One Tap
Note: This quick start guide must be read in conjunction with
(If required)
the main installation and user instructions
• Before proceeding, read the installation and user instructions
For AIO mains and vented Taps
• Check all the components are present and correct.
• Check that you have all the necessary tools Cut a 50mm hole in the bench / sink top.
• Ensure the underbench can support the product weight when full of water,
(Check the specifications in the main book and allow an extra 5-8kg when full. )
Black plastic SINK TOP
spacer
Before installing ensure the following have been provided at 50mm
the installation site: ALL THREAD
ROD Stainless
• Sufficient space in the cupboard to install all of the undersink units in accordance washer
with these Installation Instructions. Refer to technical specification for dimensions. If NOTE: make sure the tap location will allow the nozzle to drain into the sink.
required, make allowance for a booster heater. (Refer to the main book, for detailed SPIDER
installation instructions). Fit the CLAMP
BLACK STAINLESS STAINLESS STEEL
• A potable water supply connection with isolating valve inside the cupboard within PLASTIC STEEL
reach of the flexible braided hose and positioned so that the connection point and the WASHER WASHER, 6mm
stop cock will not be obstructed when all the undersink units are installed. SPACER SPIDER CLAMP, NUT
AND 6mm NUT.
• For Zip HydroTap 160/125 &160/175 models, a 220-240Vac, 10A GPO will be
required. For Zip HydroTap 240/175 models, two 220-240Vac, 10A GPOs will be SPIDER
required. (One GPO is for the Zip HydroTap and the other for the Booster heater). CLAMP NOTE: feed each of the three tubes and
NOTE: Check the cable lengths and outlet positions before proceeding. electrical cable evenly in between the legs of
NUT O-RING
• A potable cold water supply with a minimum working pressure of 172kPa and a the SPIDER CLAMP when installing.
maximum working pressure of 700kPa connected via an isolation valve.
35mm dia hole BASE
• For the mains pressure All-IN-ONE, both a hot and cold water supply will be required. Hole positioning: BLOCK ALL
• The undersink appliances must be mounted in upright positions as shown in the Position the tap such that it dispenses into
the sink bowl with ample clearance for a cup or tea pot. Alternatively, SPIDER THREAD O-RING
diagrams. the tap could be mounted away from the sink using a Zip Font, avail- ROD SINK TOP
able as an accessory. Sink BASE
IMPORTANT! Do not proceed with the installation if these BLOCK
Apply a light smearing of silicon sealant NUT
requirements are not met. on the underside of the upper spacer to USB
CABLE
ensure a watertight fi t.
Parts Supplied Description Parts Supplied Description
Mixer Tap
Fit the O-ring to the underside of the AIO tap
4-in-1 (If required) then pass all hoses through the 50mm hole.
1 off Duct kit
1x Air Duct
Hydrotap Tap 1 x Mounting
and hoses
plate
Tap
Vent kit O ring Base
1 off 1 x Kickboard UPPER UPPER RUB-
Undersink Unit RUBBER BER WASHER
with air and water- louvre WASHER Chiller
1 x Door vent Clear tube to Vent connection
filter
louvre LOWER RUBBER BLUE
1 x front vent grill NOTE: feed each of
WASHER LOWER RUB- the tubes and elec- Boiler
BER WASHER trical cable evenly in connection
1 off WASHER
WASHER between the legs of RED
1 x Restrictaflow HydroTap the BASE BLOCK
valve and Tee Booster heater NUT SPIDER.
piece for Mixer and hoses BRAIDED
NUT HOSE x 3
Taps (Supplied with White Hose White ring Blue ring on
240/175 models)
For HydroTap and Mixer taps Ext. Mains on LHS to RHS mains IN to
cut a 35mm hole in the bench / sink top. Mains in Mixer IN
1 off Mains water BENCH TOP Blue band
connection hose Mixer IN From Mixer OUT to Tap - Vented version only
Ø35mm Red band
Mixer Out
801600 - Zip Quick Start Guide - October 2013 - V1.06
Page 8 of 28

Major components and accessories

Description
1 x
Celsius Arc
Boiling or chilled or
chilled sparkling tap
1 x
Celsius Cube
Boiling or chilled or
chilled sparkling tap
and components
TM
Vent kit
(C ,CS models only)
1 x Outlet vent (C)
2 x Outlet vent (CS)
1 x Inlet vent
1 x
Command-Centre
with air and water
filters
1 x Mains water
connection hose
1 x T-piece &
adaptor
1 x User guide and
ZIP HydroTap
®
User Guide
• Tap Operation...................(Pages 2-5) 1 x Quick start
• LCD Screen & Menu .......(Pages 6-18)
Maintenance.................... (Pages 18-20)
•
Date of Installation.........
•
BC160/125G4
BC240/175G4
BCH160/125G4
BCH240/175G4
AV160/125G4
AN160/125G4
AV240/175G4 guide
AN240/175G4
1 x Installation
Affix Model Number Label
Here
801599
instruction
801599 - HydroTap User Guide - Nov 2013 UK - V1.05 Page 1 of 20
1 x
CO gas cylinder
2
assembly
(CS models only)
Accessories
TM
*ZT200G4 kit to fit filters FL1100
802149UK Celsius residential - Installation instructions -Jan 2016 v2.03
Description
Scale filter
installation kit
*ZT200G4
Filter not included.
Replacement
internal 0.2 micron
filter
ZT402
1 X
CO gas cylinder
2
ZT400
Recommended
water block
HE45004