Zip HydroTap G4 Celsius User Manual
Hide thumbs
Also See for HydroTap G4 Celsius:
- Installation instructions manual (29 pages) ,
- User manual (20 pages) ,
- Installation instructions manual (28 pages)
Related Manuals for Zip HydroTap G4 Celsius
Summary of Contents for Zip HydroTap G4 Celsius
- Page 1 ZIP HydroTap G4 ® Celsius User Guide Affix model number label here 802701UK 802701UK - Celsius Comm User Guide - Jan 2016 - V2.02 Page 1 of 20...
-
Page 2: Table Of Contents
Table of contents ap operation ........... Page 2 • T • Tap warning lights ........Pages 3 to 4 • LCD screen & menu ......... Pages 5 to 16 • Filter maintenance ........Pages 17 to 18 • Changing the CO cylinder ...... -
Page 3: Tap Operation
Tap operation To dispense mixed hot and cold water The mixer tap lever is operated as a conventional ‘flick mixer’. The hot direction is marked with a red dot and the cold direction with a blue dot, for dispensing cold to warm water. -
Page 4: Tap Warning Lights
If there is a fault with the system, both the safety light and the warning light will flash for half a second on and half second off until the fault is rectified. (See, System information, page 7) or call Zip on 0845 6 005 005, 0345 6 005 005. - Page 5 LCD Screen Zip HydroTap G4 features a ‘TOUCH’ screen for easy setup and operation ® adjustment. (See page 20 for home menu icons). Boiling window Safety lock icon Sleep mode icon Energy mode icon Status window Set boiling water temperature...
- Page 6 LCD Screen menu Main Sub menu Sub menu Section menu options English Language German • Product info. • Module Revision Serial number Information Product number Calibration • Filters log • Filters • System faults • Faults found • Filter flush • Start/Stop • Filter reset • Internal/External...
- Page 7 LCD Screen operation - Section A A. Set language • Chilled Press the [MENU] button for main menu. • Press the [Language] button. • Select the preferred language. • Press [<=] button for the previous menu. LCD Screen operation - Section B B.
- Page 8 LCD Screen operation - Section C C. Install Once your Zip HydroTap G4 unit has been installed, Go to the install menu to ® configure the system settings for your product. Example, boiling screen Sub menu 1. - Filter flush.
- Page 9 Caution In general, boiling water units may vent steam from the tap spout. Take care to avoid personal injury whenever this occurs. The Zip HydroTap G4 is equipped with a self-calibrating program. On start ® up, the controls take the system through a calibration process. Once this mode is completed the system reverts back to normal operation.
- Page 10 This can only be done by a Zip technician. Please contact your Zip service provider for further assistance.
- Page 11 LCD Screen operation - Section E E. Security The Zip HydroTap G4 allows the appliance coordinator to set up a password ® to protect against users changing the preferred system settings. To set a password • Press the [MENU] button for main menu.
- Page 12 • Press [NEXT] button to set time. Set temperature Zip HydroTap G4s are designed to operate within 1ºC to 2ºC of set point ® for boiling water, between 5ºC to 9ºC for chilled water and 3ºC to 5ºC for chilled sparkling water .
- Page 13 LCD Screen operation - Section G Filter Zip HydroTap G4 allows the user to adjust filter life and edit filter usage. ® Note The filter life may be set as a function of litres used, or in months from the filter change. When the first of these functions is reached (i.e.
- Page 14 LCD Screen operation - Section G Energy modes (boiling models) This mode allows the HydroTap G4 to go into energy saving mode. There ® are two options available: sleep mode and on/off mode. In sleep mode the unit will go to “Sleep” after a 2hr period of inactivity. The boiling water will gradually drop to either 68°C or room temp, as shown in the table below and the chilled water will be ON or OFF.
- Page 15 LCD Screen operation - Section G Note Any attempt, during off mode, to dispense water, will bring the unit out of sleep mode. The unit will return to sleep mode after 2 hours of non use. Please allow sufficient time for the water to reach the set temperature after disabling the sleep mode.
- Page 16 LCD Screen operation - Section G Safety (boiling models) To allow the safety setting to be changed using the touch screen • Press the [MENU] button for main menu. • Press the [Settings] button. • Enter your 4-digit password and press [Enter]. •...
-
Page 17: Filter Maintenance
Filter Maintenance Water filter The HydroTap G4 notifies when filter replacement is due. If you notice one ® of the following, you will need to change the filter. • The change filter light will flash until reset. • The filter percentage will show 0% on the home screen. Note Depending on local water quality conditions and usage, the filter may require changing anywhere from 1,000 Ltrs to 10,000 Ltrs. - Page 18 Filter maintenance Warning: If the HydroTap ® is switched off for a long period of time (e.g. more than a weekend), run water through the chilled water outlet for at least 5 minutes before consumption. Air Inlet Filter The HydroTap G4 air filter is conveniently located on the outside of the ®...
-
Page 19: Changing The Co Cylinder
Changing the CO cylinder • Turn the CO cylinder regulator off (anti-clockwise). The knob will screw up and away from the cylinder. • Remove the cylinder from the cupboard and disconnect the regulator. If the braided hose is removed from the regulator, be careful not to lose the small plastic sealing olive, located inside the end of the hose. -
Page 20: Home Menu Icons
Telephone: 0845 6 005 005 Mobile: 0345 6 005 005 As Zip policy is one of continuous product improvement, changes to specifications may be made without prior notice. Images in this booklet have been modified and may not be true representations of the finished goods.