YASKAWA L1000A Quick Start Manual page 38

7 Parameter Table
No. Name
d1-19 Nominal Speed
Intermediate
d1-20
Speed 1
Intermediate
d1-21
Speed 2
Speed reference values for separate speed
Intermediate
d1-22 selection inputs. Setting units are
Speed 3
determined by parameter o1-03. Refer to
d1-23 Relevel. Speed
page 23.
Inspection
d1-24 Operation
Speed
Leveling
d1-26
Speed
Leveling Used when d1-18 = 0 or 3. If the speed
Speed reference selected is lower than d1-28, then
d1-28
Detection the drive uses the leveling speed as the
Level speed reference.
Used when d1-18 = 0 or 3. If the speed
Inspection
reference selected is between d1-28 and d1-
Speed
d1-29 29, then the speed reference is regarded as
Detection
the Inspection Speed, and the inspection
Level
operation sequence is activated.
This parameter must be set to the power
supply voltage.
Input Voltage WARNING! Drive input voltage (not motor
E1-01
Setting voltage) must be set in E1-01 for the
protective features of the drive to function
properly.
Maximum
V/f pattern settings
E1-04 Output
Frequency
Maximum
E1-05
Voltage
Base
E1-06
Frequency
Mid Output
E1-07
Frequency
Mid Output
E1-08 Frequency
Voltage
E1-07, E1-08, and E-10 are available only
Minimum
in V/f Control and Open Loop Vector
E1-09 Output
Control.
Frequency
For linear V/f characteristics, set the same
Minimum
values to E1-07 and E1-09. With these
Output
settings, the drive will disregard the value
E1-10
Frequency
set to E1-08.
Voltage
Parameters must be set so that:
E1-09  E1-07  E1-06 E1-04
E1-13 Base Voltage
Motor Parameters
E2-01 Rated Current
E2-02 Rated Slip
No-Load
E2-03
Current
Motor data for Induction Motors.
E2-04 Motor Poles
Line-to-Line
E2-05
Resistance
Leakage
E2-06
Inductance
EN 38
Description
V/f Pattern
Output Voltage (V)
E1-05
E1-13
E1-08
E1-10
E1-09 E1-07 E1-06
Frequency (Hz)
No. Name
E5-02 Rated Power
E5-03 Rated Current
E5-04 Motor Poles
Stator
E5-05
Resistance
d-Axis
E5-06
Inductance
q-Axis
E5-07
Inductance
Induction Volt.
E5-09
Const. 1
Induction Volt.
E5-24
Const. 2
Encoder 1
F1-01
Resolution
Encoder 1
F1-05 Rotation
Direction
Encoder
F1-50
Selection
Communicatio
n Speed of
F1-52
Serial Encoder
Selection
Multi-Function Digital Inputs / Outputs
Terminal S3 to
H1-03 to
S8 Function
H1-08
Selection
Terminal M1-
H2-01 to
M6 Function
H2-03
Selection
Terminal P1-
H2-04,
C1, P2-C2
H2-05
Function Sel.
Note:
Major functions are listed at the end of the table.
E1-04
Multi-Function Analog Inputs
Terminal A1,
H3-01,
A2 Signal
H3-09
Level Sel.
Terminal A1,
H3-02,
A2 Function
H3-10
Selection
Terminal A1,
H3-03,
A2 Gain
H3-11
Setting
Terminal A1,
H3-04,
A2 Bias
H3-12
Setting
Multi-Function Analog Outputs
Terminal FM,
H4-01,
AM Monitor
H4-04
Selection
YASKAWA ELECTRIC TOEP C710616 33G AC Drive L1000A - Quick Start Guide
Description
PM Motor Settings
Motor data for permanent magnet motors.
E5-09 is set as peak-to-peak value for one
motor phase in units of 0.1 mVs/rad
(electrical angle).
E5-24 is set as phase-to-phase RMS value in
units of 0.1 mVmin (mechanical angle).
If a value is set to E5-09, then E5-24 must
be set to 0.0 and vice versa.
PG Speed Control Card
Sets the encoder resolution.
0: A phase leads B in up direction
1: B phase leads A in up direction
0: EnDat 2.1/01, 2.2/01 Serial
Communication + Sin/Cos
1: EnDat 2.2/22 Serial Communication
2: HIPERFACE
0: 1M bps/9600 bps
1: 500k bps/19200 bps
2: 1M bps/38400 bps
3: 1M bps/38400 bps
Selects the function of terminals S3 to S8.
Sets the function for the relay outputs M1-
M2, M3-M4, and M5-M6.
Sets the function for the photocoupler
outputs P1-C1 and P2-C2.
0: 0 to 10 V
1: -10 to 10 V
0: Speed bias
2: Auxiliary speed 1
3: Auxiliary speed 2
14: Torque compensation
1F: Through mode
Sets the level of the input value selected in
H3-02 and H3-10 when 10 V is input at
terminals A1 and A2.
Sets the level of the input value selected in
H3-02 and H3-10 when 0 V is input at
terminals A1 and A2.
Selects the data to be output through multi-
function analog output terminals FM and
AM.