Mitsubishi Electric MELSEC FX3U Programming Manual page 951

FX /FX /FX Series Programmable Controllers
3G 3U 3UC
Programming Manual - Basic & Applied Instruction Edition
2) FX-30P
FX-30P is applicable to FX
a) FX PLCs
3G
FX PLC
3G
version
Ver. 1.00 or later
b) FX PLCs
3U
FX PLC
3U
version
Ver. 2.20 or later
Ver. 2.61 or later
c) FX PLCs
3UC
FX
3UC
version
Ver. 1.00 or later
Ver. 2.61 or later
2. In the case of programming tool (version) not applicable to FX
(using an alternative model)
Even using a programming tool not applicable to the FX
when an alternative model is set.
In this case, however, programming is enabled only in the function ranges such as instructions, device ranges
and program sizes available in a PLC selected as the alternative model. Use a programming tool which can
select the model (FX3G, FX3U(C) or FX3UC) to change parameters such as memory capacity and file
register capacity.
Use a programming tool which can select "FX3G" to perform communication using the standard USB port
built in FX PLCs..
3G
Model to be
programmed
FX PLC
3G
FX PLC
3U
FX PLC
3UC
*1. For Ver. 8.13P to 8.24A of GX Developer, the PLC type is FX3UC.
*2. "FX " is selected when the FX-10P(-E) is used.
2N
3. Program transfer speed and programming tool
When any of the following interfaces are used for GX Developer (Ver.8.13P or later), reading and writing of
programs and monitoring of devices can be executed at high speed (115.2 kbps) in the FX
PLCs.
FX-30P can be executed at high speed (115.2kbps) in FX
• Standard built-in port or expansion board FX
When the RS-232C/RS-422 converter FX-232AWC-H or USB/RS-422 converter FX-USB-AW is connected
• Expansion board FX
• Special adapter FX
• Expansion board FX
When any of the following interfaces are used for GX Developer (Ver.8.72A or later), reading and writing of
programs and monitoring of devices can be executed at high speed (115.2 kbps) in the FX
FX-30P can be executed at high speed (115.2kbps) in FX
• Standard built-in port (RS-422) or expansion board FX
When the RS-232C/RS-422 converter FX-232AWC-H is connected
• Expansion board FX
• Special adapter FX
In earlier programming software, the communication speed is 9,600 or 19,200 bps.
In GX Developer, the communication speed can be set using the following procedure:
Select "Online" → "Transfer setup..." → "PC side I/F", and double-click the "Serial" icon.
, FX and FX
3G 3U
Model name
FX-30P
Model name
FX-30P
PLC
Model name
FX-30P
Model to be set
→
FX
3G
→
FX *1
3U(C)
→
*1
FX
3U(C)
-232-BD for RS-232C
3U
-232ADP(-MB) for RS-232C
3U
-USB-BD for USB
3U
-232-BD for RS-232C
3G
-232ADP(-MB) for RS-232C
3U
A Programming Tool Applicability and Version Upgrade History
PLCs starting with the following version:
3UC
Applicable FX-30P version
Ver.1.00 or later
Applicable FX-30P version
Ver.1.00 or later
Not applicable
Applicable FX-30P version
Ver.1.00 or later
Not applicable
3G
, FX and FX
3G 3U 3UC
Priority High → Low
→
FX *4
1N
→
FX
3UC
→
FX
3UC
, FX PLCs.
3U 3UC
-422-BD for RS-422
3U
PLCs.
3G
-422-BD for RS-422
3G
A-1 Programming Tool Applicability
Remarks
Remarks
Available for FX PLCs prior to
3U
Ver. 2.61
Remarks
Available for FX PLCs prior to
3UC
Ver. 2.61
, FX and FX PLCs
3U 3UC
PLCs, programming is enabled
→
FX
FX *2
2
2N
→
FX FX
2N 2
→
FX FX
2N 2
and FX
3U
PLCs.
3G
31
32
33
34
35
36
37
3UC
38
A
B
949