Page 3
FAX: +86-755-26770160 Suggestions and Feedback To improve the quality of ZTE product documentation and offer better services to our customers, we hope you can give us your suggestions and comments on our documentation and fax this form to 0086-755-26770160; or mail to “...
The ZXR10 WAS IP wireless access system is the IP wireless access system developed by ZTE. It consists of a series of wireless access network products, such as wireless network card, wireless access point (AP) and DSL 2-in-1 wireless router.
Page 6
Statement: The actual product may differ from what is described in this manual due to frequent update of ZTE products and fast development of technologies. Please contact the local ZTE office for the latest updating information of the product. Warning...
Page 11
Fig. 2.2-1 installation instruction ....................2-5 Fig. 2.2-2 Soldered Connectors....................2-6 Fig. 3.-1 Serial Port Configuration ..................3-3 Fig. 3.1-2 Telnet to W800A....................3-3 Fig. A.1-1 Label of the Straight Through Ethernet Cable ...............3 Fig. A.1-2 Label of the Straight Through Power Supply Ethernet Cable ..........3...
Page 13
Table 1.2-1 Safety Symbols and Descriptions ................1-3 Table 2.1-1 IDs and Frequencies of Channels ................2-2 Table 3.6-1 W800A Working Channels .................. 3-45 Table A.1-1 Connections of Straight Through Ethernet Cables (RJ45) ..........1 Table A.1-2 Connections of Straight Through Power Supply Ethernet Cables (C-RJ45-001)....2...
1 Safety Precautions This chapter introduces the safety precautions of this product and safety symbols used in this manual. 1.1 Safety Precautions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ( 1) This device may not cause harmful interference, and ( 2) this device must accept any interference received, including interference that may cause undesired operation.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual personnel who had passed the training can install, operate and maintain it. ZTE assumes no responsibility for consequences resulting from violation of general specifications for safety operations or of safety rules for design, production and use of equipment.
Chapter 1 Safety Precautions Table 1.2-1 Safety Symbols and Descriptions Safety Symbols Meaning Call for notice Call for antistatic measures Warn against electric shock Caution against scald Warn against laser Caution against microwave Four types of safety levels are available: danger, warning, caution and note. To the right of a safety symbol is the text description of its safety level.
Page 18
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Note: Any failure to take the reminder seriously may lead to injury accidents or damage to the equipment. & Remark, reminder, tip… The remarks, prompt and tips in addition to safety statements.
2.1 Installation Preparations 2.1.1 Installation Preparation Flow Before installing the W800A, the engineering personnel should confirm that such work as solution design, project survey and W800A basic configurations have been completed. Brief introductions to the preparations required for installation are as follows.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Table 2.1-1 IDs and Frequencies of Channels Channel ID Central Frequency Low End/High End Frequency of the Channel 2412MHz 2401/2423MHz 2417MHz 2411/2433MHz 2422MHz 2416/2438MHz 2427MHz...
RUN indicator should flash slowly (about once per second). If the indicator is not in the normal status, you can log on to the W800A in the hyper terminal mode and check whether the version is loaded normally. If necessary, you can reload the version (refer to Section 7.3 Version Loading and Upgrade for...
The ground bolt can be installed on the interface board of the shell, for grounding. The W800A can be used not only on the desktop or ceiling but also on the wall, so it is easily to be used.
Page 23
Chapter 4 Installation and Debugging Fig. 2.22-1 installation instruction When the W800A is installed on the ceiling, for the ceiling in plaster or floor, the W800A antenna can be directly installed on the ceiling; for the ceiling in metal, if the...
PoE source end device W112P or W105P. For the detailed description, refer to Appendix B. To power on the W800A, connect the power adapter or Ethernet cable for powering the Ethernet for the W800A. After being powered on, the W800A will start automatically, without any operation by users.
Page 25
Chapter 4 Installation and Debugging Ensure that the route between W800A and Internet/customer server is smooth. Ensure that each client in the W800A coverage area can access Internet normally. Ensure that in the whole engineering coverage area, the clients can be roaming...
This chapter describes the operation methods and configuration commands of the W800A command line configuration. 3.1 Overview The W800A provides the Command Line Interface (CLI) for configuring the W800A data. The CLI configuration of the W800A has the following features:...
Page 28
Ctrl + C: Give up all the input contents. Enter the new line and the prompt character will appear. When the serial port mode is used for configuring the W800A, the serial port attribute configurations of the hyper terminal are shown in Fig. 3.-1.
Chapter 5 Command Line Configuration Fig. 3.-1 Serial Port Configuration When the Telnet mode is used for configuring the W800A, you just need input “telnet/W800A working IP address”, as shown in Fig. 3.1-2. By default, the W800A working IP address is 192.168.1.254 and the subnet mask is 55.255.255.0.
Exiting mode: exit Default prompt character: wlan> Note: After logging on to the W800A in Telnet, the common user can enter the user mode only once the user name and password authentications are passed. The default user name is “root” and default password is “public”. To avoid the case in which the...
3.3.2 Saving the Configuration Data to FLASH Command mode: Privileged mode. Function: Saving the configuration data to FLASH. Command format: write flash. 3.3.3 Restoring the Default Configuration Command mode: Privileged mode Function: Deleting the database, recovering the default configuration of the W800A...
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual and reset it. Command format: default enable 3.3.4 Resetting the Software Command mode: Privileged mode Function: Resetting the W800A. Command format: reboot 3.3.5 Entering the Configure Mode Command mode: Privileged mode Function: Entering the configure mode.
Chapter 5 Command Line Configuration 3.4.1 Bridge Configuration bridge aging-time Command mode: Configure mode Function: Configuring the aging time of the Bridge Forward Table (FDB) MAC address. Command format: bridge aging-time <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions The aging time of the FDB MAC address (unit: <value>...
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3.4.3 Configuring the Configuration Server Command mode: Configure mode Function: Configuring the parameters of configuration server: IP address, interception port number of the TCP and the interception port number of UDP.
Page 35
Chapter 5 Command Line Configuration Command mode: Configure mode Function: Configuring the IP address parameters of the default gateway of the DHCP server. Command format: dhcp server gateway <A.B.C.D> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <A.B.C.D> IP address IP address of the gateway.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter descriptions: Parameter Name Value Range Parameter Descriptions The start flag of the DHCP server. If it is “true”, the DHCP server will be started when...
Chapter 5 Command Line Configuration Parameter Name Value Range Parameter Descriptions IP address with a management multicast address <A.B.C.D> range of 224.0.0.1 ~ integrated management server, 224.1.88.88 by 239.255.255.254. default. The management interception port number of the <value> 0~65535 integrated management server, 2800 by default. 3.4.6 802.1X Parameter Configuration dot1x enable Command mode: Configure mode...
Page 38
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Command mode: Configure mode Function: Configuring the domain name in the EAP-MD5 authentication mode. Command format: dot1x md5-domain <string> Parameter descriptions: Parameter Name Value Range...
Page 39
Chapter 5 Command Line Configuration Command mode: Configure mode Function: Configuring the time-out time of the 802.1x authentication server. Command format: dot1x server-timeout <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions The authentication server time-out time (unit: <value> 1~255 second), 60 by default.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter Name Value Range Parameter Descriptions The 802.1x sending period (unit: second), 3 by <value> 1~255 default. 12. dot1x wpa-domain Command mode: Configure mode Function: Configuring the domain name in the WPA authentication mode.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual iapp max-user Command mode: Configure mode Function: Configuring the maximum user quantity (the quantity of the users can be accessed). Command format: iapp max-user <value>...
0 or 1. 3.4.12 IP Network Parameter Configuration ip address Command mode: Configure mode Function: Adding the IP address of the W800A management interface. Command format: [no] ip address <A.B.C.D > <A.B.C.D > [second]...
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual <A.B.C.D > IP address Initial IP address of the host address pool. <A.B.C.D > IP address End IP address of the host address pool. <A.B.C.D >...
Chapter 5 Command Line Configuration l2-separate mode Command mode: Configure mode Function: Configuring the two-layer separation working mode. Command format: l2-separate mode {simple_mode | gateway_mode } Parameter descriptions: Parameter Name Value Range Parameter Descriptions {simple_mode| simple_mode, Selecting the simple mode or gateway mode for the gateway_mode } gateway_mode two-layer separation.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter Name Value Range Parameter Descriptions Specified module names: BSP, DATABASE, 80211, BRIDGE, IAPP, DHCP, IPPOOL, DOT1X, <module> RADIUS, ACL, The module containing the log printing messages.
Chapter 5 Command Line Configuration Parameter Name Value Range Parameter Descriptions The MAC address sending the MAC packet. Two methods can be used for specifying the source address: {<xx-xx-xx-xx-xx-xx address One is to use the format of 48-bit 6 hexadecimal >...
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string > 1 ~ 32 characters User name <string > 1 ~ 32 characters User password. 3.4.19 QoS Configuration...
Page 49
Chapter 5 Command Line Configuration Parameter Name Value Range Parameter Descriptions <string > 1 ~ 255 characters Character string of the accounting shared secret key radius-server authen Command mode: Configure mode Function: Adding or deleting the authentication server of an ISP. Command format: [no] radius-server authen <string >...
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual radius-server retry-times Command mode: Configure mode Function: Configuring the retrying times of the RADIUS authentication of an ISP. Command format: radius-server retry-times <string> <value> Parameter descriptions:...
Page 51
Chapter 5 Command Line Configuration snmp access-mode Command mode: Configure mode Function: Configuring the local agent can be accessed by all the hosts or the host in access-host. Command format: snmp access-mode {all|list} Parameter descriptions: Parameter Name Value Range Parameter Descriptions all: All the users can access it.
Page 52
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter descriptions: Parameter Name Value Range Parameter Descriptions Serving as the end mark of inputting character <End-Mark> Any character. string. A management variable content in the MIB II <string>...
Page 53
Chapter 5 Command Line Configuration Parameter Name Value Range Parameter Descriptions A management variable in the MIB system group, <value> 0~241920000 describing the NE code of the managed equipment. snmp nodecreatdate Command mode: Configure mode Function: Configuring the creation time information of the NE of the managed equipment.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter Name Value Range Parameter Descriptions Serving as the end mark of inputting character <End-Mark> Any character. string. RFC1213, a management variable in the MIB <string>...
Chapter 5 Command Line Configuration Command mode: Configure mode Function: Generating SSH server secret key. Command format: ssh server generate-key rsa ssh server auth isp-name Command mode: Configure mode Function: Configuring SSH with the ISP name of the authentication server authenticated by radius.
Page 56
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Command mode: Configure mode Function: Configuring the forwarding delay time of the spanning tree protocol bridge. Command format: stp bridge forward-delay <value> Parameter descriptions: Parameter Name...
Page 57
Chapter 5 Command Line Configuration Parameter Name Value Range Parameter Descriptions The priority of the spanning tree protocol bridge, <value> 0~65535 32768 by default. stp enable Command mode: Configure mode Function: Enabling or disabling the spanning tree protocol function. Command format: [no] stp enable stp interface path-cost Command mode: Configure mode Function: Configuring the path cost of the spanning tree protocol interface.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter descriptions: Parameter Name Value Range Parameter Descriptions {eth0|wlan0|wlan1} eth0, wlan0, wlan1 Configured interface. The state of the spanning tree protocol interface, {enable|disable} Enable, disable enable by default.
Chapter 5 Command Line Configuration Command format: tftp get <A.B.C.D> {runbin | zxipcmd.dat | database.dat} Parameter descriptions: Parameter Name Value Range Parameter Descriptions The TFTP server IP address represented by dotted <A.B.C.D> IP address decimal. {runbin| Runbin, The full file name (including the extension name) zxipcmd.dat| zxipcmd.dat, of the version file set to be transmitted on the TFTP...
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Command mode: Configure mode Function: Enabling or disabling VLAN function. Command format: [no] vlan enable vlan manager-vlanid Command mode: Configure mode Function: Configuring the VLAN of the management interface.
Chapter 5 Command Line Configuration Parameter descriptions: Parameter Name Value Range Parameter Descriptions NA: Not been configured; CA: Canada; CN: China; TW: Taiwan; FR: France; {NA|CA|CN|TW| GE: Germany; FR|GE|HK|KR| HK: Hongkong; MX|GB|US } KR: Korea; MX: Mexico; GB: Britain; US: USA; The default value is CN.
Page 62
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> Alarm levels. show bridge Command mode: Configure mode Function: Showing the bridge configuration parameter information. Command format: show bridge...
Page 63
Chapter 5 Command Line Configuration Command format: show iapp show interface Command mode: Configure mode Function: Showing the parameter information of the interface configuration. Command format: show interface {ethernet|wlan} {0|1} show ip 1) show ip address Command mode: Configure mode Function: Showing IP address information.
Page 64
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 10. show l2-separate Command mode: Configure mode Function: Showing the parameter information of the 2-layer separation configuration. Command format: show l2-separate 11. show logmsg Command mode: Configure mode Function: Showing all the configuration information and configuration historical commands of log printing.
Page 65
Chapter 5 Command Line Configuration Command mode: Configure mode Function: Showing the parameter information of manage-user configuration. Command format: show manage -user 16. show multi-essid Command mode: Configure mode Function: Showing the parameter information of multi-essid configuration. Command format: show multi-essid <value> Parameter descriptions: Parameter Name Value Range...
Page 66
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual configuration. Command format: show snmp community 3) show snmp nodeinfo Command mode: Configure mode Function: Showing the parameter information of snmp nodeinfo configuration. Command format: show snmp nodeinfo...
Chapter 5 Command Line Configuration Command format: show stp bridge 2) show stp interface Command mode: Configure mode Function: Showing the parameter information of stp interface configuration. Command format: show stp interface 23. show telnet-idletime Command mode: Configure mode Function: Showing the parameter information of the automatic exiting time when the Telnet window is idle.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Note: All the information of the corresponding interface can be configured in this mode. 3.5.1 Exiting the Ethernet Interface Configuration Mode Command mode: Ethernet interface configure mode Function: Exiting the Ethernet interface configuration mode and entering the configure mode.
Page 69
Chapter 5 Command Line Configuration Parameter descriptions: Parameter Name Value Range Parameter Descriptions {OpenSystem| OpenSystem, The wireless authentication mode is configured as ShareKey} ShareKey open system or shared secret key mode. 80211 essid Command mode: Wireless interface configure mode Function: Configuring the wireless network ESSID. Command format: 80211 essid <string>...
Page 70
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Function: Configuring the wireless standard working mode of the wireless interface. Command format: 80211 wirelessmode {11a|11b|11g|help} [channel <num>] [rate <value>] Parameter descriptions: Parameter Name Value Range Parameter Descriptions 11a: Configuring 800A as the 802.11a working mode.
Chapter 5 Command Line Configuration Table 3.6-1 W800A Working Channels Abbreviations Full Names of 11a Available Channel 11b Available Channel 11g Available Channel of Nations and Nations and Numbers Numbers Numbers Zones Zones CHINA 0 (Auto), 149, 153, 157, 0 (Auto), 1, 2, 3, 4, 5,...
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3.6.3 Exiting the Wireless Interface Configuration Mode Command mode: Wireless interface configure mode Function: Exiting the wireless interface configuration mode and entering the configure mode.
Chapter 5 Command Line Configuration [priority <value >] Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 1 ~ 32 characters ESSID name. <value > 1~4094 The VLAN ID corresponding to the ESSID. The maximum user quantity corresponding to the <value >...
Page 74
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual <character/hex> Parameter descriptions: Parameter Name Value Range Parameter Descriptions {key1|key2| key1, key2, The article number of the secret key to be key3|key4} key3, key4 configured.
Chapter 5 Command Line Configuration Parameter descriptions: Parameter Name Value Range Parameter Descriptions Configuring the shared secret key of the WPA <string> 8 ~ 36 characters encryption. security wpa rekey-interval Command mode: Wireless interface configure mode Function: Configuring the WPA mode to be used. Command format: security wpa rekey-interval <value>...
Page 76
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Parameter descriptions: Parameter Name Value Range Parameter Descriptions {ap|repeater} ap, repeater The working mode of the equipment. 3-50...
A.1 Making of Ethernet Cables A.1.1 Making of Straight Through Ethernet Cables (RJ45) In IP wireless access system, the following network cables must adopt the straight through Ethernet cables: The Ethernet cable between the Ethernet switch (end A) and W112P (end B). When no Ethernet switch is used, AP will directly connect with the AC downlink port, at this time, the Ethernet cable between the AC (end A) and AP (end B) must be straight through Ethernet cable.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Table A.1-2 Connections of Straight Through Power Supply Ethernet Cables (C-RJ45-001) End A Signal Name Conductor Color End B Signal Name Conductor Color Data receiving Rx+...
The signals and connection methods mentioned here are designed according to the signal definitions of the ZTE AC equipment interface. If the AC in the actual engineering is not from ZTE, modify the cable making methods according to the actual conditions.
ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual RJ45J Fig. A.1-3 Label of the Crossover Ethernet cable In the diagram, “**m” indicates the actual length of the cable; “J” after “RJ45” indicates that this is the crossover Ethernet cable.