Page 1
ZXR10 Router/Ethernet Switch Command Manual (Voice and Video Service Volume) Version 4.8.22 ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P. R. China 518057 Tel: (86) 755 26771900 Fax: (86) 755 26770801 URL: http://ensupport.zte.com.cn E-mail: support@zte.com.cn...
Page 2
The contents of this document are protected by copyright laws and international treaties. Any reproduction or distribution of this document or any portion of this document, in any form by any means, without the prior written consent of ZTE CORPO- RATION is prohibited.
Purpose operation of ZXR10 router and Ethernet switch. This manual is intended for engineers and technicians who perform Intended Audience operation activities on ZXR10 router and Ethernet switch. This manual contains the following chapters: What Is in This Manual Chapter...
Page 6
ZXR10 Command Manual (Voice and Video Service Volume) � ZXR10 Router/Ethernet Switch Command Manual (Multicast Volume) � ZXR10 Router/Ethernet Switch Command Manual (IPv6 Vol- ume) Confidential and Proprietary Information of ZTE CORPORATION...
To search a command, do as follows: 1. Find the desired command by referring to ZXR10 Router/Eth- ernet Switch Command Manual — Command Index. 2. Find command details by the volume, chapter/section and page of the obtained command.
Do not describe the history command if this entry does not exist. Auxiliary Function The auxiliary function for ZXR10 devices is as follows. 1. In any command mode, enter a question mark (?) after the DOS prompt of the system, a list of available commands in the command mode will be displayed.
ENTER. The ^ is below the first character of the input incorrect command, keyword or parameter. 3. ZXR10 router/Ethernet switch allows the command or key- word to be abbreviated into a character or character string that uniquely identifies this command or keyword. For example, the show command can be abbreviated to sh or sho.
Page 10
ZXR10 Command Manual (Voice and Video Service Volume) Mode Prompt Admis- Entry Functions sion Command Mode Inter- ZXR10(config- Global interface Configures face if)# config- port config- uration parameters uration mode and selects mode a port type depending on the keyword...
Page 11
Configures ospf OSPFv3 parameters ZXR10(config- Global ip vrf Configures config- vrf)# config- uration uration parameters mode mode VFI con- Global ZXR10(config- Configures figu- config- vfi)# VPLS related ration uration parameters mode mode Confidential and Proprietary Information of ZTE CORPORATION...
............21 shutdownvoice-port ............. 21 timeouts ................22 vad..................22 voice-port.................23 cancel-truncate Use this command to cancel truncating the called number. Enable Purpose the truncating called number function with no command. Dial-up peer configuration Command Modes Confidential and Proprietary Information of ZTE CORPORATION...
� This command is only applied to the dial-peer in pots type. Instructions � It is only applied to ZXR10 GAR and ZXR10 ZSR. clear call-history Use this command to clear the call history information of the spec- Purpose ified port.
� The modified voice port configuration will take effect in the next dial-up. � It is only applied to ZXR10 GAR and ZXR10 ZSR. This example describes how to enable the comfort noise on port Example voice_3/1. ZXR10(config)#voice-port voice_3/1...
� The modified dial-peer configuration will take effect in the next dial-up. � It is only applied to ZXR10 GAR and ZXR10 ZSR. This example describes how to configure the phone number Example 0251111 for peer 1 in pots type.
The modified voice port configuration will take effect in the next Instructions dial-up. � It is only applied to ZXR10 GAR and ZXR10 ZSR. This example describes how to set the energy threshold to 200, Example which is used for receiving the DTMF code on port voice_3/1.
The modified voice port configuration will take effect in the next dial-up. � It is only applied to ZXR10 GAR and ZXR10 ZSR. This example describes how to configure the echo cancellation Example sampling time length on the voice_3/1 port as 16.
GK Client saved in the GK Server can be updated in time. � It is only applied to ZXR10 GAR and ZXR10 ZSR. h323-description Use this command to configure the h323 gateway descriptor. Re- Purpose store the default with no command.
GK Server, only one alias is avail- able for a gateway and the latest configured character string is valid. � It is only applied to ZXR10 GAR and ZXR10 ZSR. h323-gateway voip id Use this command to configure the GK Server name and IP address Purpose corresponding to the gateway.
If no gateway interface is specified, other configuration about the GK Client is meaningless. � It is only applied to ZXR10 GAR and ZXR10 ZSR. h323-gateway voip tech-prefix Use this command to configure the technical prefix for the GK Purpose Server to identify the gateway type.
The modified voice port configuration will take effect in the next Instructions dial-up. � It is only applied to ZXR10 GAR and ZXR10 ZSR. This example describes how to input the gain value 20 dB on port Example voice_3/1. ZXR10(config)#voice-port voice_3/1...
ZXR10 Command Manual (Voice and Video Service Volume) � It is only applied to ZXR10 GAR and ZXR10 ZSR. This example describes how to associate dial-peer 1 in pots type Example to port voice_1/3. ZXR10(config)#dial-peer voice 1 pots ZXR10(config-pots1)#port voice_1/3...
The modified dial-peer configuration will take effect in the next dial-up. � It is only applied to ZXR10 GAR and ZXR10 ZSR. This example describes how to configure the network address of Example dial-peer 100 in VOIP type as 168.1.1.1.
� show dial-peer voice summary: It shows simple configura- tion information of all dial-peers. � It is only applied to ZXR10 GAR and ZXR10 ZSR. show gateway Use this command to show the gateway information. Purpose Privileged EXEC...
� show voice-port summary: It shows the simple configura- tion information of all voice ports. � It is only applied to ZXR10 GAR and ZXR10 ZSR. shutdowndial-peer Use this command to configure the management status of the dial- Purpose peer as down. Change the management status of the dial-peer to up with the no command.
The modified voice port configuration will take effect in the next Instructions dial-up. � It is only applied to ZXR10 GAR and ZXR10 ZSR. Use this command to enable the mute detection function. Disable Purpose the mute detection function with the no command.
Command Modes voice-port <voice-port> Syntax Syntax Description <voice-port> Specifies the voice port It is only applied to ZXR10 GAR and ZXR10 ZSR. Instructions This example describes how to enter the configuration mode of the Example voice_3/1 port. ZXR10(config)#voice-port voice_3/1 ZXR10(config-voice-port)#...
Page 30
ZXR10 Command Manual (Voice and Video Service Volume) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...
<rule-list> Syntax Syntax Description <rule-list> One or more rule numbers, in the range of 1~256 This example describes how to clear CAC rule 1. Example ZXR10(config)#nas ZXR10(config-nas)#clear iptv cac-rule 1 Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Voice and Video Service Volume) create iptv cac-rule Related Commands show iptv cac-rule show iptv cac-rule statistics clear iptv channel Use this command to clear a channel. Purpose NAS configuration Command Modes clear iptv channel <channel-list> Syntax...
MAC address. This example describes how to create a MAC-based CAC rule 1 on Example port gei_1/1 of vlan 1. ZXR10(config)#nas ZXR10(config-nas)#create iptv cac-rule 1 port gei_1/1 vlan 1 mac-base clear iptv cac-rule Related Commands iptv cac-rule name...
One or more rule numbers, in the range of 1~256 <rule-name> Rule name, not more than 32 characters This example describes how to specify a name zte for CAC rule 1. Example ZXR10(config)#nas ZXR10(config-nas)#iptv cac 1 name zte create iptv cac-rule...
Related Commands show iptv cac-rule iptv cac-rule prvtime Use this command to configure the maximum preview time for a Purpose CAC rule. NAS configuration Command Modes iptv cac-rule <rule-list> prvtime <preview-time> Syntax Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Voice and Video Service Volume) Syntax Description <rule-list> One or more rule numbers, in the range of 1~256 <preview-time> The maximum preview times for previewing users under the CAC rule, in the range of 1~65535 If the maximum preview time is not configured for a rule, it will be Instructions the global maximum preview time.
ZXR10(config-nas)#iptv channel 1 name cctv1 create iptv channel Related Commands show iptv channel iptv control Use this command to enable or disable the IPTV control function. Purpose NAS configuration Command Modes iptv control {enable | disable} Syntax Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Voice and Video Service Volume) Syntax Description enable Enables the IPTV control function. disable Disables the IPTV control function. This example describes how to enable the IPTV control function. Example ZXR10(config)#nas ZXR10(config-nas)#iptv control enable show iptv control...
The global minimum preview interval serves as the minimum pre- Instructions view interval of the CAC rule by default. This example describes how to set the global minimum preview Example interval to 20s. ZXR10(config)#nas ZXR10(config-nas)#iptv control prvinterval 20 Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Voice and Video Service Volume) show iptv control Related Commands iptv control prvtime Use this command to set the global maximum preview time. Purpose NAS configuration Command Modes iptv control prvtime <preview-time> Syntax Syntax Description <preview-time> The maximum preview time, in the range of...
Page 41
The minimum preview interval MaxPrvTime The maximum preview time CurPrvCount Current preview count CurOrdAccessNum Current order access number HisOrdAccessNum Historical order access number CurPrvAccessNum Current preview access number HisPrvAccessNum Historical preview access number Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Voice and Video Service Volume) CurAccessNum Current access number HisAccessNum Historical access number Order number Ordered channel number Preview number Previewed channel number Query number The port of this rule is the channel number of the source port...
Use this command to show the configured channel information. Purpose Privileged EXEC Command Modes show iptv channel [{id <channel-id>| ame <channel-name>}] Syntax Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Voice and Video Service Volume) Syntax Description <channel-id> Channel ID, in the range of 0~263 <channel-name> Channel name, 1~32 characters This example describes how to show all channels. Example ZXR10(config)#show iptv channel MaxGroupNum :264 CurrentConfigTotal:3 HistoryConfigTotal:3 Name...
Command Modes show iptv client [{channel <channel-id>| index <client-inde Syntax x>| mac <mac-address>| name <user-name>}] Syntax Description <channel-id> Channel ID, in the range of 0~263 <client-index> Client index, in the range of 0~63 Confidential and Proprietary Information of ZTE CORPORATION...
Page 46
ZXR10 Command Manual (Voice and Video Service Volume) <mac-address> The client’s MAC address <user-name> User name, 1~32 characters � This example describes how to show all IPTV users. Example ZXR10(config)#show iptv client MaxUserNum :4096 CurrentUserNum :3 HistoryUserNum:3 Index Name Port...
Syntax This example describes how to show all channels. Example ZXR10(config)#show iptv control State :enable LoginTime :10s MaxPrvCount ResetPeriod :300s MinPrvInterval:5s MaxPrvTime :60s The displayed information descriptions are shown below. Confidential and Proprietary Information of ZTE CORPORATION...
Page 48
ZXR10 Command Manual (Voice and Video Service Volume) State IPTV state LoginTime The minimum time for identifying the user MaxPrvCount The maximum preview count ResetPeriod Period to reset the preview count MinPrvInterval The minimum preview interval MaxPrvTime The maximum preview time...