Page 1
ZXR10 Router/Ethernet Switch Command Manual (Network Management Volume) Version 4.8.22 ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P. R. China 518057 Tel: (86) 755 26771900 Fax: (86) 755 26770801 URL: http://ensupport.zte.com.cn E-mail: support@zte.com.cn...
Page 2
The contents of this document are protected by copyright laws and international treaties. Any reproduction or distribution of this document or any portion of this document, in any form by any means, without the prior written consent of ZTE CORPO- RATION is prohibited.
About This Manual..........i Command Introduction ........1 Manual Use Guide............1 Description of Man-Machine Commands ......1 Auxiliary Function ............2 Command Mode ............. 3 SNMP Configuration ..........7 show snmp ..............7 show snmp config............7 show snmp Engine-id ............8 show snmp group ............
Page 4
lfap backup-server2 ............28 lfap enable ..............28 lfap disable ..............29 lfap fas-server...............29 lfap flow-expired-time ............30 lfap ka-interval..............30 lfap max-send-fun-size...........30 lfap message-response-interval ........31 lfap server-retry-interval ..........31 lfap statistic sample-rate ..........32 lfap update-interval ............32 show lfap config ............33 show lfap statistic............33 Group Configuration ........35 group erase-member .............35 group handtime.............36 group holdtime..............36...
Purpose operation of ZXR10 router and Ethernet switch. This manual is intended for engineers and technicians who perform Intended Audience operation activities on ZXR10 router and Ethernet switch. This manual contains the following chapters: What Is in This Manual Chapter...
To search a command, do as follows: 1. Find the desired command by referring to ZXR10 Router/Eth- ernet Switch Command Manual — Command Index. 2. Find command details by the volume, chapter/section and page of the obtained command.
Do not describe the history command if this entry does not exist. Auxiliary Function The auxiliary function for ZXR10 devices is as follows. 1. In any command mode, enter a question mark (?) after the DOS prompt of the system, a list of available commands in the command mode will be displayed.
ENTER. The ^ is below the first character of the input incorrect command, keyword or parameter. 3. ZXR10 router/Ethernet switch allows the command or key- word to be abbreviated into a character or character string that uniquely identifies this command or keyword. For example, the show command can be abbreviated to sh or sho.
Page 12
ZXR10 Command Manual (Network Management Volume) Mode Prompt Admis- Entry Functions sion Command Mode Inter- ZXR10(config- Global interface Configures face if)# config- port config- uration parameters uration mode and selects mode a port type depending on the keyword Subin- ZXR10 (config-...
Page 13
Configures ospf OSPFv3 parameters ZXR10(config- Global ip vrf Configures config- vrf)# config- uration uration parameters mode mode VFI con- Global ZXR10(config- Configures figu- config- vfi)# VPLS related ration uration parameters mode mode Confidential and Proprietary Information of ZTE CORPORATION...
Syntax show snmp config Use this command to display configuration information of all SN- Purpose MPs. All modes Command Modes show snmp config Syntax show snmp group Related Commands show snmp user Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Network Management Volume) show snmp engine_id show snmp show snmp Engine-id Use this command to display local engine identifier of SNMP. SNMP Purpose engine, as the core part in an SNMP entity, is used to authenticate the receiving/sending of SNMP messages, and withdraw PDU as- sembled messages to communicate with the SNMP program.
The <community-name> is an arbitrary string (1~32) and the <view-name> is an MIB view name. This example describes how to set SNMP packets community as Example myCommunity with read-write access. ZXR10(config)#snmp-server community myCommunity view myview rw snmp server view Related Commands snmp-server contact...
ZXR10 Command Manual (Network Management Volume) (MIB). Remove the system contact information with the no form of this command. Global configuration Command Modes snmp-server contact <mib-syscontact-text> Syntax no snmp-server contact Syntax Description <mib-syscontact-te Text that describes the system contact xt>...
This example describes how to configure the agent to be able to Example send all notifications. ZXR10(config)#snmp-server enable inform ZXR10(config)#snmp-server host 168.1.1.1 inform version 2c public snmp-server host Related Commands snmp-server enable trap Use this command to enable Simple Network Management Protocol Purpose (SNMP) trap notifications.
ZXR10 Command Manual (Network Management Volume) no snmp-server engine_id Syntax Description <engine-id> Local SNMP engine ID, 1~24 char- acters. The default value is 830900020300010289d64401. It must be expressed with a hexdecimal number This command is supported after the platform version 4.6.02.
And the read view string, write view string and notification view string are named view1. ZXR10(config)#snmp-server group group1 v3 priv read view1 write view1 notify view1 show snmp group...
This example describes how to configure the send address, port, Example version and type of a host trap or inform. ZXR10(config)#snmp-server host 168.1.1.1 ver 1 community-name ospf ZXR10(config)#snmp-server host 168.1.1.1 ver 3 auth user10 ospf snmp snmp-server enable inform Related Commands...
This example describes how to specify the system location of the Example Management Information Base (MIB) object for Simple Network Management Protocol (SNMP). ZXR10(config)#snmp-server location this is ZXR10 in china snmp-server packetsize Use this command to establish control over the largest Simple Net- Purpose work Management Protocol (SNMP) packet size permitted when the SNMP server is receiving a request or generating a reply.
The following example shows how to enter a plain-text password Example for user1 in group1. And the MD5 authentication password is 12345678 and CBC-DES encryption password is 12345678. ZXR10(config)#snmp-server user user1 group1 v3 auth md5 12345678 priv des56 12345678 show snmp user Related Commands...
Use the included | excluded keywords to include or exclude a subtree. The following example creates a view that includes all objects in Example the MIB subtree. ZXR10(config)#snmp-server view myViewName 1.3.6.1.2.1 included snmp-server community Related Commands Confidential and Proprietary Information of ZTE CORPORATION...
Page 26
ZXR10 Command Manual (Network Management Volume) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...
Indicates to directly compare the value of the selected variable with the threshold rising-threshold Rising threshold of the sampling statistics, <value> range: -2147483647~2147483647 <event-index> Event index if the threshold is exceeded, range: 1~65535 Confidential and Proprietary Information of ZTE CORPORATION...
“Alloc buffer error or Resource unavailable”. Use this command to configure history group statistics on the 100 Example Mbps Ethernet interface. The sampling time is 300 seconds. ZXR10(config)#interface fei_1/1 ZXR10(config-if)#rmon collection history 1 owner zte buckets 100 interval 300 show rmon history Related Commands...
Example log_trap_event. Meanwhile, record it in log and send trap infor- mation to the management station. The management station community is public. ZXR10(config)# rmon event 1 log trap public description log_trap_event owner ZTE Confidential and Proprietary Information of ZTE CORPORATION...
“Alarm table is empty.” � “Event table is empty.” � Use this command to display RMON alarm information. Example ZXR10(config)#show rmon alarm rmon alarm Related Commands rmon collection history rmon collection statistics rmon event Confidential and Proprietary Information of ZTE CORPORATION...
Page 32
ZXR10 Command Manual (Network Management Volume) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...
Enable this function with the web enable command. Global configuration Command Modes web disable Syntax The WEB network management is disabled by default. Defaults This example describes how to disable WEB network management. Example ZXR10(config)#web disable web enable Related Commands Confidential and Proprietary Information of ZTE CORPORATION...
Page 34
ZXR10 Command Manual (Network Management Volume) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...
Use this command to specify the address of FAS backup server 1 Instructions with the LFAP function. This example describes how to set the address of lfap backup Example server 1 to 192.1.1.120. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Network Management Volume) ZXR10(config)#lfap fas-server 192.1.1.120 lfap fas-server Related Commands lfap backup-server2 lfap backup-server2 Use this command to configure the address of the lfap backup Purpose server 2. Delete the setting with the no form of this command.
Light-weight Flow Accounting Protocol (LFAP). This example describes how to set the Flow Admission Service Example (FAS) server address of Light-weight Flow Accounting Protocol (LFAP) to 192.1.1.168. ZXR10(config)#lfap fas-server 192.1.1.168 lfap bakup-server1 Related Commands lfap backup-server2 Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Network Management Volume) lfap flow-expired-time Use this command to set flow expired time interval of LFAp. Delete Purpose the setting with the no form of this command. Global configuration Command Modes lfap flow-expired-time <second> Syntax no lfap flow-expired-time...
ZXR10(config)#lfap message-response-interval 120 lfap server-retry-interval Use this command to set the time interval for LFAP to retry con- Purpose necting with the LFAP server (FAS). Delete the setting with the no form of this command. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Network Management Volume) Global configuration Command Modes lfap server-retry-interval <second> Syntax no lfap server-retry-interval Syntax Description <second> Time interval for LFAP to retry connecting with the LFAP server (FAS), in seconds, range: 1~2000 The time interval for LFAP to retry connecting with the LFAP server Defaults (FAS) is 60 seconds by default.
: 0 messages received error count messages received success count : 0 messages sent count FAR messages sent count FUN messages sent count messages sent count ARA messages sent count Confidential and Proprietary Information of ZTE CORPORATION...
Page 42
ZXR10 Command Manual (Network Management Volume) messages sent count messages received count messages received count ARA messages received count VRA messages received count messages received count FER messages received count CRN messages received count CAN messages received count show lfap config...
..............50 ztp start ................50 ztp timer ................50 ztp vlan................51 group erase-member Use this command to enable group members to erase original con- Purpose figuration. Global configuration Command Modes group erase-member {all |<member_id>} Syntax Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Network Management Volume) Syntax Description Specifies all group members to erase configuration <member_id> Specifies a group member to erase configuration � This command is supported after the platform version 4.6.02. Instructions � This command can be executed only on the command switch.
This command can be executed only on the command switch. This example describes how to add the device to the group based Example on the MAC address of the switch and set its member identifier to ZXR10(config)#group member mac oodo.doco.0204 member 2 show group members Related Commands...
<name> Syntax Description <name> Group name, 1~32 characters The default group name is ZTE GROUP-xx.xx.xx (xx.xx.xx is the Defaults last three bits of the MAC address of the command switch). � This command is supported after the platform version 4.6.02.
ZXR10(config)#group switch-type candidate � This example describes how to configure the switch as a command switch and assign the address pool 192.168.10.1 255.255.255.0 to the switch. ZXR10(config)#group switch-type command ip-pool 192.168.10.1 mask 255.255.255.0 Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Network Management Volume) group tftp-server Use this command to set the group TFTP Server address. Remove Purpose the configured group TFTP Server address with the no form of this command. Global configuration Command Modes group tftp-server <ip_addr>...
� This example displays group information when the switch is a Example candidate switch. ZXR10(config)#show group SwitchRole :CANDIDATE_SWITCH � This example displays information when the switch is a com- mand switch. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Network Management Volume) Cmdr.ZXR10(config)#show group SwitchRole :COMMANDER_SWITCH Group name :ZTE GROUP-c0.19.00 Group holdtime :80 seconds Group handtime :8 seconds Group tftp server :none TrapHost :none Group ip-pool :ip_pool 192.168.1.1 mask 255.255.255.0 Manage Vlan show group candidates Use this command to show information about all candidates in the Purpose group.
Cmdr.ZXR10(config)#show group members index memberId MacAddress IpAddress Mask Status Hostname ----------------------------------------------------------------- 1 00.d0.d0.fb.02.03 192.168.1.2 255.255.255.0 Up Mem1.ZXR10 show group members member-num Use this command to show information about the specified mem- Purpose ber in the group. All modes Command Modes show group members member-num <mem_id>...
ZXR10 Command Manual (Network Management Volume) show zdp Use this command to display information about ZTE neighbor Dis- Purpose covery protocol (ZDP). All modes Command Modes show zdp Syntax This command is supported after the platform version 4.6.02. Instructions This example describes how to display information about ZTE Example neighbor Discovery protocol (ZDP).
Syntax This command is supported after the platform version 4.6.02. Instructions This example describes how to display detailed information about Example the collected switch. ZXR10(config)#show ztp device-list Last collection vlan id is 1 Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Network Management Volume) Last collection time is 1760 ms index DeviceID MacAddress SwitchType Platform Hostname ------------------------------------------------------ 00.d0.d0.c0.19.00 CANDIDATE_SWITCH ZXR10_3952 ZXR10 00.d0.d0.fb.02.03 CANDIDATE_SWITCH ZXR10 2826E ZXR10 show ztp device-list Use this command to show information about all devices collected Purpose by the topology.
2 does not receive a new neighbor discovery packet in 100 seconds, it will delete device 1 from its neighbor list. This example describes how to set the holdtime of neighbor dis- Example covery to 200 seconds. ZXR10(config)#zdp holdtime 200 Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Network Management Volume) show zdp Related Commands zdp timer Use this command to set the time interval for sending neighbor Purpose discovery packets. Restore the default value with the no form of this command. Global configuration Command Modes zdp timer <time>...
This command is supported after the platform version 4.6.02. Instructions This example describes how to set the delay of the device for topol- Example ogy collection to 100 milliseconds. ZXR10(config)#ztp hop-delay 100 Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 Command Manual (Network Management Volume) show ztp Related Commands ztp port-delay Use this command to set the delay of the port for topology collec- Purpose tion. Restore the default value with the no form of this command. Global configuration Command Modes ztp port-delay <time>...
This command is supported after the platform version 4.6.02. Instructions This example describes how to set the switch to conduct topology Example collection in VLAN 4. ZXR10(config)#ztp vlan 4 show ztp Related Commands Confidential and Proprietary Information of ZTE CORPORATION...