Table of Contents
Advertisement
Disassembly Procedures
• To avoid risk of electrical shock, personal injury, or death; disconnect electrical and gas supply before servicing.
• To avoid risk of death; always test unit for gas leaks after repairs are completed.
Safety Valve
1. Turn off electrical power and gas to the range.
2. Disconnect gas and power from unit.
3. See "Oven Burner Ignitor" procedures, (steps 1-5).
4. Disconnect gas line to safety valve.
5. Remove screws securing safety valve mounting from
support bracket.
6. Slide safety valve forward to release metal tabs from
support bracket.
7. Replace and reassemble in reverse order.
Top Burner Venturi
1. Turn off electrical power and gas to the range.
2. Remove maintop assembly, see maintop procedures.
3. Slide venturi to the side out of bracket, then slide
back to release venturi from top burner orifice.
4. Replace and reassemble in reverse order.
Pressure Regulator
1. Turn off electrical power and gas to the range.
2. Slide unit away from the wall to gain access to power
cord, gas line, and rear panel.
3. Disconnect power from unit and gas line from
regulator.
4. Disconnect regulator from manifold.
5. Replace and reassemble in reverse order.
Manifold
1. Disconnect regulator from manifold, see "Pressure
Regulator" procedure.
2. Remove maintop, see maintop procedures.
3. Remove control panel, see "Conrtol Panel"
procedures.
4. Remove surface valves and oven thermostat from
manifold.
5. Remove manifold from unit.
6. Replace and reassemble in reverse order.
Oven Thermostat
1. Remove control panel, see "Control Panel"
procedure, (steps 1-5).
2. Remove maintop, see maintop procedures.
3. Remove gas supply line and pilot tubing to oven
thermostat.
4. Remove screws securing oven thermostat to
manifold.
5. Open the oven door and release capillary clip from
oven cavity.
!
WARNING
6. Carefully withdraw capillary tube from oven cavity.
7. Remove oven thermostat from unit.
8. Replace and reassemble in reverse order.
Oven Light Bulb/Oven Light Socket
1. Disconnect electrical power to range.
2. Using a glove, unscrew (counterclockwise) oven light
bulb.
Proceed with the following steps for oven light socket
removal.
3. Locate tabs on each side of the light socket and
squeeze inward while pulling outward on the socket.
4. Disconnect wires from light socket and remove.
5. Reverse procedure to reinstall light socket.
Oven Liner Removal
NOTE: Require's removal of range from cabinet.
1. Turn off electrical power and gas to the range.
2. Slide unit away from the wall to gain access to power
cord, gas lines, and rear panel.
3. Disconnect power from unit and gas line.
4. Remove oven door, racks, and oven bottom.
5. Remove thermostat capillary tube and clip.
6. Remove chip cover and screws securing oven vent.
7. Disconnect wiring, and withdraw capillary tube.
8. Remove oven light cover, bulb, and socket.
9. Release oven tank brackets at rear. Maneuver tank
from frame.
10.Reverse procedure to assemble.
NOTE: When reinstalling new liner, use flat sheet metal
strips 4 inches wide by 28 inches long to prevent
insulation from bunching up, as new liner is
installed.
Oven Door
1. Open oven door to gain access to screws securing
door to hinges, (one each side).
2. Remove screws securing door to hinges.
2. Close oven door to first stop position (1/3 open) then
grasp both sides and lift up off the hinges.
To avoid personal injury or property damage, do not
lift oven door by the handle, brakage may occur.
49
!
CAUTION
RS2310004 Rev. 1
Advertisement
Table of Contents
