Danfoss VLT HVAC Operating Instructions Manual page 61

®
VLT HVAC Drive Operating Instructions
Q3-20 Digital Reference
3-02 Minimum reference
3-03 Maximum reference
3-10 Preset reference
5-13 Terminal 29 digital input
5-14 Terminal 32 digital input
5-15 Terminal 33 digital input
Q3-30 Single Zone Int. S.
1-00 Configuration mode
20-12 Reference/feedb unit
3-02 Minimum reference
3-03 Maximum reference
6-24 Terminal 54 low ref/feedb value 6-10 Terminal 53 low voltage
6-25 Terminal 54 high ref/feedb value 6-11 Terminal 53 high voltage
6-26 Terminal 54 Filter time constant 6-14 Terminal 53 low ref/feedb. value 20-00 Feedback 1 source
6-27 Terminal 54 live zero
6-00 Live zero timeout time
6-01 Live zero timeout function
20-81 PID normal/inverse control
20-82 PID start speed [RPM]
20-21 Setpoint 1
20-93 PID proportional gain
20-94 PID integral time
Q3-40 Fan Functions
22-60 Broken belt function
22-61 broken belt torque
22-62 Broken belt delay
4-64 Semi auto bypass setup
1-03 Torque characteristics
22-22 Low speed detection
22-23 No-flow function
22-24 No-flow delay
22-40 Minimum run time
22-41 Minimum sleep time
22-42 Wake-up speed
2-10 Brake function
2-17 Over-voltage control
1-73 Flying start
1-71 Start delay
1-80 Function at stop
2-00 DC hold/preheat
4-10 Current motor speed direction
See also
parameter groups.
0-20
Value:
None
Display Text 1
Q3-3 Closed Loop Settings
Q3-31 Single Zone Ext. S
1-00 Configuration mode
20-12 Reference/feedback
3-02 Minimum reference
3-03 Maximum reference
6-15 Terminal 53 high ref/feedb. value 20-01 Feedback 1 conversion
6-24 Terminal 54 low ref/feedb value
6-25 Terminal 54 high ref/feedb value 20-04 Feedback 2 conversion
6-26 Terminal 54 Filter time constant
6-27 Terminal 54 live zero
6-00 Live zero timeout time
6-01 Live zero timeout function
20-81 PID normal/inverse control
20-82 PID start speed [RPM]
Q3-4 Application Settings
Q3-41 Pump Functions
22-20 Low power auto setup 1-03 Torque characteristics
22-21 Low power detection
22-22 Low speed detection
22-23 No-flow function
22-24 No-flow delay
22-40 Minimum run time
22-41 Minimum sleep time
22-42 Wake-up speed
22-26 Dry pump function
22-27 Dry pump delay
1-03 Torque characteristics
1-73 Flying start
VLT ® HVAC Drive Operating Instructions
Display Line 1.1 Small
MG.11.A4.02 - 09.10.06. VLT ®
6. How to programme the frequency converter
Q3-2 Open Loop Settings
Q3-21 Analog Reference
3-02 Minimum reference
3-03 Maximum reference
6-10 Terminal 53 low voltage
6-11 Terminal 53 high voltage
6-14 Terminal 53 low ref/feedb. value
6-15 Terminal 53 high ref/feedb. value
Q3-32 Multi Zone / Adv.
1-00 Configuration mode
20-12 Reference/feedb unit
3-02 Minimum reference
3-03 Maximum reference
3-15 Reference 1 source
3-16 Reference 2 source
20-03 Feedback 1 source
20-06 Feedback 3 source
20-07 Feed back 3 conversion
6-10 Terminal 53 low voltage
6-11 Terminal 53 high voltage
6-14 Terminal 53 low ref/feedb. value
20-93 PID proportional gain
20-94 PID integral time
4-56 Warning feedback low
4-57 Warning feedback high
20-20 Feedback function
20-21 Setpoint 1
20-22 Setpoint 2
Q3-42 Compressor Functions
1-71 Start delay
22-75 Short cycle protection
22-76 Interval between starts
22-77 Minimum run time
5-01 Terminal 27 mode
5-02 Terminal 29 mode
5-12 Terminal 27 digital input
5-13 Terminal 29 digital input
5-40 Function relay
1-73 Flying start
for a detailed description of the Function Setups
Display Text 2
Display Text 3
Date and Time Readout
[0]
Profibus Warning Word
[37]
is a registered Danfoss trademark
6
[38]
[39]
[89]
[953]
61