Fault Code Tables - Taylor-Dunn B0-248-36 Operation, T Roubleshooting And Replacement Parts Manual

SAFETY RULES AND OPERATING INSTRUCTIONS
NOTE: Most faults are a result of a fault in the control
system that will require service by a qualified
technician. These faults are shown here for
reference only.
Operator correctable faults are shown in
bold and underlined.
Level 1 Faults
Fault Code Description
F01000 P/S Motor Overheated
F01001 Motor Brush Fault
F01002 Pump Motor Brush Fault
F01003 P/S motor Brush Fault
F01004 Low Battery Volts
F01005 Controller Overheated
F01006 Traction Motor Hot
F01007 Pump Motor Overheated Stop the vehicle and allow
F01008 Wiring fault
Level 4 Faults
Fault Code Description
F04000 Open Contactor
F04001 Contactor Welded
F04002 Steer POT Fault
F04003 Sequence Fault
F04004 F&R Fault
F04005 F&R Fault
F04006 Interlock Fault
F04007 Inch Switch Fault
F04008 Steer Fault
F04009 Low Battery Volts
F04010 High battery Volts
F04011 Out of Range Fault
F04012 CRC Fault
F04013 Capacitor Fault
Safety Rules
Page 14

Fault Code Tables

What to do
Stop the vehicle and allow
the system to cool down.
Refer to service technician
Refer to service technician
Refer to service technician
Batteries are empty and
require charging. If this
fault does not reset after the
charge cycle is complete
then there may be a
problem with the charger or
batteries.
Refer to qualified service
technician.
Stop the vehicle and allow
the system to cool. This
could be a result of an
overloaded vehicle.
Stop the vehicle and allow
the system to cool down.
This could be a result of an
overloaded vehicle
the system to cool down.
Refer to service technician
What to do
Refer to service technician
Refer to service technician
N/A
Start up switches were not
operated in the correct
order. Refer to Vehicle
Operation Guidelines for
correct sequence.
Refer to service technician
Direction was selected
before start switch was
closed. Place direction
selector in the OFF position
and restart.
Seat or foot interlock switch
not closed.
F&R switch NOT in neutral.
Refer to service technician
Extreme low battery voltage
at the controller. May be a
result of severely
discharged battery or
wrong battery installed.
Confirm that the correct
battery is installed and
charge the battery.
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Level 5 Faults
Fault Code Description
F05000 Contactor Over Current
F05001 Controller Fault
F05002 Configuration Error
F05003 Internal Fault
F05004 VA Fail
F05005 Data Layer Fault
F05006 MOSFET Short
F05007 Power Up Fault
F05008 Line Contactor Short
F05009 Wiring/Motor Short
F05010 Power Up Fault
F05011 Drive 0 ON
F05012 Drive 1 ON
F05013 Drive 0 OFF
F05014 Drive 1 OFF
F05015 Drv 0 MOSFET Trip
F05016 Drv 1 MOSFET Trip
F05017 Traction ON
F05018 Traction OFF
F05019 MOSFET Short_L
F05020 Power Up Fault
F05021 Traction Welded
F05022 Traction MOSFET
F05023 Auto Zero
F05024 Drive 0 ON L
F05025 Drive 1 ON L
F05026 Drive 0 OFF L
F05027 Drive 1 OFF L
F05028 0 MOSFET trip L
F05029 1 MOSFET trip L
F05030 Traction ON L
F05031 Traction OFF L
F05032 MOSFET Short R
F05033 Power Up Fault
F05034 Traction Welded
F05035 Traction MOSFET
F05036 Auto Zero R
F05037 Drive 0 ON R
F05038 Drive 1 On R
F05039 Drive 0 OFF R
F05040 Drive 1 OFF R
F05041 0 MOSFET Trip R
F05042 1 MOSFET Trip R
F05043 Traction ON R
F05044 Traction OFF R
F05045 Stack Corrupt
F05046 Open Contactor
Level 2 Faults
Fault Code Description
F02000 Throttle Fault
F02001 Throttle Fault
F02002 Belly Switch Fault
F02003 Open Field
F02004 Open Field L
F02005 Open Field R
What to do
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician
What to do
Occurs if throttle control
voltage is high at start
up indicating that the
throttle pedal was
depressed when the
start switch was closed.
If the pedal was not
depressed, then refer to
qualified service
technician.
Refer to service technician
Refer to service technician
Refer to service technician
Refer to service technician