GE b30 Instruction Manual page 540

Direct outputs
application example .....................................................................5-242
clearing counters ................................................................................ 7-2
error messages .................................................................................... 7-7
settings ...............................................................................................5-242
specifications ..................................................................................... 2-28
Directional overcurrent
see Phase, Ground, and Neutral directional
Directional polarization
.................................................................5-181
Disconnect switch
FlexLogic operands .......................................................................5-152
logic ......................................................................................................5-137
settings ...............................................................................................5-135
Discover button
................................................................................... 3-56
Disk space required
........................................................................... 3-45
Display settings
.................................................................................... 5-25
Disposal
..................................................................................................10-20
Dispose of battery
............................................................................10-15
Disturbance detector
FlexLogic operands .......................................................................5-152
internal ................................................................................................5-129
DNP
connections remaining ................................................................. 6-10
select protocol ................................................................................... 5-37
settings ................................................................................................. 5-38
DOS partition alarm error message
Downgrade firmware
.....................................................................10-11
Downgrade software
......................................................................10-10
Download files ...................................................................................... 10-3
Drag and drop files
............................................................................... 4-3
E
EGD protocol
actual values ......................................................................................... 6-9
settings ................................................................................................. 5-88
Electrostatic discharge specifications
Elements
..................................................................................................... 5-4
End of life
...............................................................................................10-20
Energy metering
actual values ...................................................................................... 6-18
clearing ........................................................................................ 5-27, 7-2
specifications ..................................................................................... 2-24
EnerVista UR Setup
command line interface ..................................................................C-1
EnerVista UR setup
drag and drop files ............................................................................. 4-3
event recorder ...................................................................................... 4-2
firmware upgrade or downgrade ..........................................10-11
installation ........................................................................................... 3-46
oscillography ......................................................................................... 4-2
requirements ..................................................................................... 3-45
restart relay ........................................................................................ 5-45
Engineer
create logic diagram ...................................................................... 4-32
Error messages ................................................................................. 4-40
Warning messages ......................................................................... 4-41
iv
......................................... 7-10
.................................... 2-32
Engineer command to force logoff
Environment backup
......................................................................... 10-7
Equations
definite time curve ..........................................................5-177, 5-199
FlexCurves ........................................................................................ 5-177
FlexLogic ............................................................................................ 5-162
FlexLogic, protect ................................................................................4-9
IAC curves ......................................................................................... 5-175
IEC curves ......................................................................................... 5-174
IEEE curves ....................................................................................... 5-173
Equipment mismatch error
Error messages
.......................................................................................7-5
device not recognized ................................................................. 10-11
in Engineer ........................................................................................... 4-40
Ethernet
actual values .........................................................................................6-7
configuration ...................................................................................... 3-54
Quick Connect ................................................................................... 3-59
settings .................................................................................................. 5-31
Ethernet Global Data settings
Ethernet port turn on or off
Event cause indicators ..................................................................... 4-20
Event Cause LEDs ................................................................................ 4-22
Event recorder
actual values ...................................................................................... 6-22
clearing ........................................................................................5-26, 7-2
records explained ...............................................................................4-2
specifications ..................................................................................... 2-23
system logs ......................................................................................... 5-24
via EnerVista software ......................................................................4-2
EVENTS setting
.........................................................................................5-5
Export settings to file
........................................................................ 10-6
F
F485
............................................................................................................ 3-45
Faceplate
........................................................................................3-2, 4-19
Factory default reset
................................................................5-7, 5-21
Far-End Fault Indication .................................................................. 5-32
Fast form-C relay specifications
Fast transient testing specifications
Features
.......................................................................................................2-1
Fiber signal loss detection
File transfer by IEC 61850
File transfer by TFTP
.......................................................................... 5-86
Files
delete ....................................................................................10-18, 10-19
download ............................................................................................. 10-3
drag and drop .......................................................................................4-3
protect FlexLogic with password .................................................4-9
protect with password ......................................................................4-7
transfer to relay ...................................................................................4-1
Firmware lock self-test
.................................................................... 7-10
Firmware revision
............................................................................... 6-25
Firmware upgrade or downgrade
Firmware version does not match EnerVista
Flash memory ......................................................................10-18, 10-19
B30 BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL
..............................................7-4
..............................................................7-6
...................................................... 5-88
........................................................... 5-31
................................................. 2-28
........................................ 2-32
............................................................. 5-32
.............................................................. 5-85
.......................................... 10-11
................... 10-11
INDEX