Test Pattern - Extron electronics DTP CrossPoint 84 IPCP Programming Manual

Command and Response Table for Matrix Switcher Commands (continued)
Command Function

Test pattern

Enable a test pattern
Disable test patterns
View test pattern selection
Screen saver timeout and status
Set screen saver to go black
immediately
Set screen saver timeout duration
Example:
Set screen saver to never go black
View screen saver timeout duration
View screen saver status
Scaler output rate
Set scaler output rate
Example:
View scaler output rate
Captive screw and Ethernet serial port insertion enables
Enable an input captive screw serial
port insertion
Enable an input Ethernet serial port
insertion
Set all RS-232 input insertions
View input insertion
View all input insertions
Enable an output captive screw
serial port insertion
Enable an output Ethernet serial
port insertion
Set all RS-232 output insertions
View RS-232 output insertion
View all output insertions
NOTE: X1& = TP and insertion input number
X1( = TP (scaled) and insertion output number
X3$ = Duration
X3% = Screen saver status
X3^ = Scaler output resolution and rate
X3& = Captive screw or UART
X3# = Test pattern
SIS Command Response
(Host to Unit) (Unit to Host)
EX1( X3# }
* TEST Test
EX1( }
*0TEST Test
EX1( } X3#]
TEST
E X1( }
T *0SSAV SsavT
E X1( X3$ }
T * SSAV SsavT
E }
T3*300SSAV SsavT3*300
E X1( }
T *501SSAV SsavT
E X1( } X3$]
T SSAV
E X1( } X3%]
S SSAV
EX1( X3^ }
* RATE Rate
E }
3*75RATE Rate3*73
EX1( } X3^]
RATE
RS-232 Insertion Commands
E X1& }
I *0LRPT LrptI
E X1& }
I *1LRPT LrptI
E X3& }
I *LRPT LrptI
E X1& } X3&]
I LRPT
E } X3&
ILRPT
E X1( }
O *0LRPT LrptO
E X1( }
O *1LRPT LrptO
E X3& }
O *LRPT LrptO
E X1( } X3&]
O LRPT
E } X3&
OLRPT
07 or 08
or
03 04
= Output sync instantly disabled when no active video input is selected
0
through
001 500
= Output sync never times out (default)
501
= Active input detected, timer is not running
0
1 = No active input, timer is running, output sync is still active
= No active input, timer is expired, output sync is disabled.
2
See the table on page 58.
= Captive screw RS-232 insert
0
00 = Disable (default)
= Crop
01
= Alternating pixels
02
= Crosshatch
03
DTP Crosspoint 84 IPCP Series Matrix Switchers • Programming Guide
Additional description
X1( X3#]
*
X1( ]
*0
X1( ] Disable sync whenever no input video is
*000
selected.
X1( X3$] Blank output
*
] Blank output 3 after 300 seconds
(5 minutes).
X1( ] Do not blank output
*501
X1( X3^]
Set the scaler to output
*
] Set the scaler to output 720p video at
60 Hz on output 3.
X1& ] Enable the captive screw serial port
*0
insert on input
Ethernet RS-232 insert.
X1& ] Enable the Ethernet serial port insert
*1
on input
screw serial port insert.
X3&]
X3& ] X3&
One
7 8
starting at input 7.
X1( ] Enable the captive screw serial port
*0
insert on output
Ethernet serial port insert.
X1( ] Enable the Ethernet serial port insert
*1
on output
captive screw serial port insert.
X3&]
X3& ] X3&
One
3 4
starting at output 3.
(seconds)
= Ethernet RS-232 insert (UART) (default)
1
04 = Color bars
= Grayscale
05
= Blue mode
06
= Crop and pink noise (Ch. 1/2, 48 Hz, 24-bit)
07
X1( after X3$ seconds.
X1( .
X3^ X1(
on output .
X1& . This disables the
X1&
. This disables the captive
for both available inputs,
X1(
. This disables the
X1(
. This disables the
for both available outputs,
17