Extron electronics DTP CrossPoint 84 IPCP Programming Manual page 18

Command and Response Table for Matrix Switcher Commands (continued)
Command Function
Compound image position and size
Specify all size and position values
Example:
View all size and position values
View active pixels and lines
View active pixels
X1(
NOTE: The " Apix * " portion of the response appears only when the switcher is in Verbose mode 2 or 3.
View active lines
X1(
NOTE: The " " portion of the response appears only when the switcher is in Verbose mode 2 or 3.
Alin *
View defaults
X1(
NOTE: The " " portion of the response appears only when the switcher is in Verbose mode 2 or 3.
SpecV *
Aspect ratio
Set to fill
Set to follow
View aspect ratio
Execute Auto-Image
Execute Auto-Image
Overscan
NOTE: The Overscan command applies to SMPTE input rates only (NTSC or PAL, 480p to 1080p, 50 Hz or 60 Hz).
Set overscan value
Read overscan value
Save and recall scaler presets
NOTE: If you try to recall a scaler preset that is not saved, the matrix switcher responds with the error code E13.
Save a scaler preset
Recall a scaler preset
Example:
Erase a scaler preset
Show scaler preset availabilities
NOTE: The " " portion of the response appears only when the switcher is in Verbose mode 2 or 3.
PreI
Auto memories
Enable auto memories
Disable auto memories
Show auto memory status
X% = Available
NOTE:
X1( = TP (scaled) and insertion output number
X2* = Picture adjustments
X2( = Position and size
X3) = Active pixels and active lines
X3@
= Overscan percentage
X3! = Aspect ratio fill or follow
X2@ = Scaler preset
SIS Command Response
(Host to Unit) (Unit to Host)
EX1( X2( X2( X2( X2( }
, * * * XIMG
Ximg
E }
3,+0*+0*2000*1000XIMG
Ximg3,+00000*+00000*02000*01000
EX1( } X2(
XIMG
EX1( }
APIX Apix
EX1( }
ALIN Alin
E X1( }
V SPEC
SpecV
EX1( }
*1ASPR Aspr
EX1( }
*2ASPR Aspr
EX1( } X3!]
ASPR
X1(
*A Img
E X3@ }
6* OSCN Oscn6*
E } X3@]
6OSCN
X1( X2@
2* * , 2Spr
X1( X2@
2* * . 2Rpr
2*3*5.
2Rpr3*005
E X2@ }
X2* PRST PrstX2*
51#
PreI
EX1( }
*1AMEM Amem
EX1( }
*0AMEM Amem
EX1( } X1(]
AMEM
= Not available
0
or
03 04
000 through 127 (064 = default
±
10240
Dependent on the input signal and selected scaling.
0 = 0% (default)
= fill; = follow
1 2
–
001 128
DTP Crosspoint 84 IPCP Series Matrix Switchers • Programming Guide
Additional description
X1( X2( X2( X2( X2(]
, * * *
]
X2( X2( X2(]
* * *
X1( X3)]
*
X1( X3)]
*
Show active pixels, active lines, total
pixels, and total lines.
X1( X3) X3) X2( X2(]
* * * *
X1( ] Always fill the output.
*1
X1( ] Follow the input aspect ratio.
*2
X1(]
X3@]
X1( X2@] Command character is a comma.
*
X1( X2@] Command character is a period.
*
] Recall preset 5, which becomes the
current configuration.
X2@]
X% X% X% X% ] X%
Each
1 2 3 ... 128
scaler preset, starting from preset 1.
X1( ] Set auto memories on. Previous settings
*1
for the incoming signal are recalled.
X1( ] Set auto memories off.
*0
= Available
1
Horizontal is specified from left, vertical from top
1 = 2.5% 2 = 5.0%
is the availability status of a
16