Extron electronics CrossPoint 82 DTP2 Setup Manual

DTP2 CrossPoint
The Extron DTP2 CrossPoint 82 is an eight-input seamless scaling presentation matrix switcher that supports signal
resolutions up to 4K @ 60 Hz at 4:4:4. All models feature DisplayPort, HDMI, and DTP2 inputs, an HDMI output and a scaled
DTP2 output extension to send video, audio, and control signals up to 330 feet (100 meters) over a shielded CATx cable. The
DTP2 CrossPoint 82 IPCP SA and DTP2 CrossPoint 82 IPCP MA 70 models each have a built-in Extron IPCP Pro 355M IP Link
Pro Control Processor, and an integrated 100 watt class D power amplifier. The DTP2 CrossPoint 82 delivers high image quality,
fast and reliable switching, Extron Pro DSP audio processing, seamless video transition effects, logo keying, and HDMI loop out.
The switchers can be controlled and configured over Ethernet, RS-232, or USB.
This guide provides instructions for an experienced user to set up and configure the DTP2 CrossPoint 82 (base model),
DTP2 CrossPoint 82 IPCP SA, and DTP2 CrossPoint 82 IPCP MA 70 switchers. It covers how to perform basic operations using
the front panel controls and selected Simple Instruction Set™ (SIS) commands.
NOTES:
For full installation, configuration, menus, connector wiring, and operation details, see the DTP2 CrossPoint 82 User
•
Guide at www.extron.com. For installation, configuration, and operation details of the embedded IPCP Pro 355M, see
the IPCP Pro Series User Guide.
The DTP2 CrossPoint 82 products can also be configured via the Extron Product Configuration Software (PCS),
•
available at www.extron.com. For information on using PCS, see the DTP2 CrossPoint 82 Help File.
Installation
DTP2 CrossPoint 82 Rear Panel Connectors
Figure 1 shows the rear panel of the DTP2 CrossPoint 82 IPCP SA. The DTP2 CrossPoint 82 IPCP MA 70 rear panel is the same
except that the embedded amplifier is 70 V mono while the SA model amplifier is stereo. The DTP2 CrossPoint 82 base model
rear panel does not have an embedded IPCP Pro 355M module (see figure 1,
DTP2 CROSSPOINT 82 IPCP SA
2
HDMI
100-240V~ 2.0A MAX
1 3
DP HDMI
50-60 Hz
A B
Figure 1. Rear Panel Connectors, DTP2 CrossPoint 82 IPCP SA
A
AC power connector
B DisplayPort input connector (input 1)
C HDMI (with CEC) loop out connector
D
DTP2/XTP input connectors (inputs 7
and 8)
E
HDMI (with CEC) output connector
(output 1)
F
Scaled DTP2/DTP/HDBaseT (with CEC)
output connector (output 2)
G
Over TP IR pass-through connector
~
100-240V 1.0A MAX
NOTE: The DTP2 CrossPoint 82 base model has a LAN connector to the left of the Remote
RS-232 connector (see
IPCP Pro 355M control processor.
50-60 Hz
A
82• Setup Guide
®
R
COM 1
Tx Rx G RTS CTS
IR/SERIAL
1
R R R R R R R R R R R R R R R R R R R R R R R R
S G
4 6
HDMI HDMI
7 8
SIG LINK SIG LINK
LOOP OUT
5
HDMI
HDMI
IN IN
DTP2/XTP)
INPUTS (
C D
H
Analog line audio inputs 3 and 4
I Analog mic/line audio inputs 1
and 2 and adjacent phantom
power LEDs
J
Analog line audio outputs 1
through 4
K
LAN connector
(DTP2 CrossPoint 82 base model
only, see the note and illustration
below.)
L Remote RS-232 connector
R
DTP2/XTP)
INPUTS (
2 4 6
HDMI HDMI HDMI
K in the illustration at right) instead of the LAN and AV LAN ports on the
1 3 5
DP HDMI HDMI HDMI
LOOP OUT
B C
Q ) or amplifier module (
Q
AV LAN 2 AV LAN 3
COM 2 COM 3 DIGITAL I/O
Tx Rx G Tx Rx G 1 2 3 4 G
RELAYS eBUS
2 1 2 C 3 4 C +V +S -S G
S G PWR OUT = 6W
LAN AV LAN 1
1 2
SIG LINK
OVER TP
IR
HDMI/CEC Tx Rx G
OUT
DTP2/XTP/HDBT)
OUTPUTS (
E F G H
OUTPUTS (
7 8 1
SIG LINK SIG LINK
HDMI/CEC
IN IN
D
O ).
P O
AMPLIFIED OUTPUT
2x25W(8Ω)/2x50W(4Ω)
L R
CLASS 2 WIRING
L R 1 1 2
+48V
AUX
MIC/LINE
3 4 2 3 4 RS-232 RESET
+48V
Tx Rx G
AUDIO INPUTS OUTPUTS REMOTE
I J LM N
M
Reset LED
N Reset button
O Amplified audio output (IPCP
models only)
P Aux analog line audio input
connector
Q IPCP Pro 355M Control Processor
(IPCP models only)
R HDMI inputs 2 through 6
P
DTP2/XTP/HDBT)
AUDIO INPUTS OUTPUTS
2
1
L R 1 2
+48V
SIG LINK
AUX
OVER TP MIC/LINE
IR 3 4 2 3 4
+48V
Tx Rx G
OUT
F G H
REMOTE
LAN
RESET
RS-232
Tx Rx G
K
1