Extron electronics DTP CrossPoint 84 IPCP Programming Manual page 21

Remote Port Specific and Communications Protocol SIS Commands
Symbol definitions for Remote port specific SIS commands
X5)
= Password
NOTE: The HTML language reserves certain characters for specific functions (see
X5!
= Port number
X5@
= Baud rate
X5#
= Parity
X5$
= Data bits
X5%
= Stop bits
X5! X5%
NOTE: through and
X4#
through for the RS-232 inserts.
X5^
= Port type
X5& = Verbose mode
NOTE: If tagged responses is enabled (modes 2 and 3), all read commands return the constant string and the value as the set command
does (for example, the read matrix name command
X5*
= Port timeout interval (in 10-second increments)
SIS Command and Response Table for Remote and Communications Protocol Commands
Command Function
Set administrator password
Read administrator password
Reset (clear) administrator password
Set user password
Read user password
Reset (clear) user password
Set serial port parameters
Read serial port parameters
Configure flow control
Read flow control
Configure receive timeout
NOTE: The configure command is sufficient as shown for most users, with the priority (
The response in this case is "
Read receive timeout
Set mode
Read mode
Set verbose mode
Read verbose mode
Configure current port timeout
Read current port timeout
Configure global IP port timeout
Read global IP port timeout
Up to 12 alphanumeric characters
= Remote (RS-232) port
01
—
02 05
(default),
9600
odd, even, none, mark, space (only the first letter required) (n = default)
, (default)
7 8
(default),
1
X5*
are variables for the rear panel Remote RS-232 port. These variables are repeated on page 8 as
= RS-232 (default)
0
= Clear or none (default for Telnet connection)
0
= Verbose mode (default for RS-232 or USB connection)
1
= Tagged responses for queries
2
= Verbose mode and tagged for queries
3
E }
CN
1 (= 10 seconds) -
SIS Command
(Host to Unit)
EX5) }
CA
E }
CA
E }
•CA
EX5) }
CU
E }
CU
E }
•CU
EX5! X5@ X5# X5$ X5%
* , , ,
EX5! }
CP
EX5! Y8^ Y8& }
* , CF
EX5! }
CF
EX5! Y8* Y8( }
* , CE
X5! Y8* Y8(
Cpn , ,0,00000L
•Cce
EX5! }
CE
EX5! X5^ }
* CY
EX5! }
CY
EX5& }
CV
E }
CV
E X5* }
0* TC
E }
0TC
E X5* }
1* TC
E }
1TC
DTP Crosspoint 84 IPCP Series Matrix Switchers • Programming Guide
Special Characters
= UARTs 1 — 5 (DTP input and output ports)
, ,
19200 38400 115200
2
= RS-422 (not available on DTP CrsossPoint)
1
X2)]
, returns Ipn• ).
65000 (default is 30 = 300 seconds = 5 minutes)
Response
(Unit to Host)
X5)]
Ipa•
X5)]
]
Ipa•
X5)]
Ipu•
X5)]
]
Ipu•
}
CP
X5! X5@ X5# X5$ X5%]
Cpn , , ,
•Ccp
, , ,
X5@ X5# X5$ X5%]
X5! Y8^ Y8&]
Cpn ,
•Cfl
Y8^ Y8&]
,
X5! Y8* Y8( Y9) Y9!]
Cpn •Cce , , ,
Y9)
) and length or delimiter (
] Y9)
," with the default and
Y8* Y8( Y9) Y9!]
, , ,
X5! X5^]
Cpn
•Cty
X5^]
X5&]
Vrb
X5&]
X5*]
Pti0*
X5*]
X5*]
Pti1*
X5*]
on page 20).
X3*
Additional description
Y9!
) omitted).
Y9!
values returned.
19