Siemens siprotec 7SA6 User Manual page 745

Addr. Setting Title
5017 NEG VALUE (B2)
5018 OVERFLOW (B2)
5019 Tmax OUTPUT(B2) AnalogOutputs
5021 20 mA (D1) =
5022 20 mA (D1) =
5023 20 mA (D1) =
5024 20 mA (D1) =
5026 MIN VALUE (D1)
5027 NEG VALUE (D1)
5028 OVERFLOW (D1)
5029 Tmax OUTPUT(D1) AnalogOutputs
5031 20 mA (D2) =
5032 20 mA (D2) =
5033 20 mA (D2) =
5034 20 mA (D2) =
5036 MIN VALUE (D2)
5037 NEG VALUE (D2)
5038 OVERFLOW (D2)
5039 Tmax OUTPUT(D2) AnalogOutputs
Note:
Depending on the version and the variant ordered some addresses are not used or have different default settings. The setting ranges
and presettings listed in the table refer to a nominal current value I
values are to be multiplied by 5. For setting primary values the transformation ratio of the transformer also must be taken into conside-
ration. Settings specified with an "A" can only be changed with DIGSI
7SA6 Manual
C53000-G1176-C133-1
Function Setting Options
AnalogOutputs 19.00..22.50 mA
AnalogOutputs 19.00..22.50 mA
0.10..30.00 sec; ∞
AnalogOutputs 10.0..1000.0 %
AnalogOutputs 10..100000 A
AnalogOutputs 1.0..1000.0 km
AnalogOutputs 1.0..1000.0 Miles
AnalogOutputs 0.0..5.0 mA
AnalogOutputs 19.00..22.50 mA
AnalogOutputs 19.00..22.50 mA
0.10..30.00 sec; ∞
AnalogOutputs 10.0..1000.0 %
AnalogOutputs 10..100000 A
AnalogOutputs 1.0..1000.0 km
AnalogOutputs 1.0..1000.0 Miles
AnalogOutputs 0.0..5.0 mA
AnalogOutputs 19.00..22.50 mA
AnalogOutputs 19.00..22.50 mA
0.10..30.00 sec; ∞
Default Setting
19.84 mA
22.50 mA
5.00 sec
200.0 %
20000 A
50.0 km
50.0 Miles
4.0 mA
19.84 mA
22.50 mA
5.00 sec
200.0 %
20000 A
50.0 km
50.0 Miles
4.0 mA
19.84 mA
22.50 mA
5.00 sec
= 1 A. For a secondary nominal current value I
N
®
4 under "Additional Settings".
Appendix
Comments
Output value (B2) for negative values
Output value (B2) for overflow
Maximum output time (B2)
20 mA (D1) correspond to
20 mA (D1) correspond to
20 mA (D1) correspond to
20 mA (D1) correspond to
Output value (D1) valid from
Output value (D1) for negative values
Output value (D1) for overflow
Maximum output time (D1)
20 mA (D2) correspond to
20 mA (D2) correspond to
20 mA (D2) correspond to
20 mA (D2) correspond to
Output value (D2) valid from
Output value (D2) for negative values
Output value (D2) for overflow
Maximum output time (D2)
= 5 A the current
N
B-21