Genie Z80/60 Service Manual page 119

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
June 2011 July 2013
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
REV F REV E
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
12 Boom up/down functions: Move the joystick
full stroke in the up direction. When the alarm
sounds, move the joystick in the opposite
direction full stroke until the alarm sounds
again. Return the joystick to center.
Boom extend/retract functions: Raise the
primary boom until it no longer rests on the
boom cradle. Then move the joystick full stroke
in the extend direction. When the alarm sounds,
move the joystick in the opposite direction full
stroke until the alarm sounds again. Return the
joystick to center.
Turntable rotate functions: Raise the primary
boom until it no longer rests on the boom cradle.
Move the joystick full stroke in either the left or
right direction until a drive enable zone is
reached. Move the joystick in the opposite
direction full stroke until the alarm sounds. Now
move the joystick in the opposite direction full
stroke until the alarm sounds again. Return the
joystick to center.
13 Once the function speeds have been set, press
and hold the engine start button
engine shuts off. Do not press the red
Emergency Stop button.
Note: Approximately 3 seconds after the engine
shuts off, the alarm at the ground controls will
sound to indicate the speed settings are being
saved in memory. Release the button.
14 At the ground controls, turn the key switch to
the off position, wait three seconds and then
turn the key switch to platform controls.
15 Inspect the display at the ground controls to be
sure there are no calibration faults.
Note: There should be no calibration faults shown
on the display. If calibration faults exist, repeat this
procedure.
Part No. 88619
How to Adjust the Function
Speeds
Note: Perform this procedure with the boom in the
stowed position. Refer to Section 2, Specifications.
1 Pull out the red Emergency Stop button to the
on position at both the ground and platform
controls.
2 Press and hold the enter button
ground control panel while turning the key
switch to ground controls.
3 Press the plus button
minus button
4 Press the scroll button
be adjusted is displayed.
5 Press the plus button
or press the minus button
speed.
6 Press the enter button
until the
memory.
7 Perform this procedure until the machine
function speed meets specification.
Z-80/60
Section 4 • Repair Procedures
PLATFORM CONTROLS
on the
twice, then press the
twice.
until the function to
to increase the speed
to decrease the
to save the setting in
4 - 17