Panasonic AJ-HPX2000 Operating Instructions Manual page 74

Information Item
13. System information
and warnings
14. Time code indication TCG
15. D.ZOOM
16. Extender
74 Adjustments and Settings for Recording : Viewfinder Screen Status Displays
Indication
SYSTEM ERROR- ¢¢
TURN POWER OFF
CARD ERR ¢
REC WARNING
BACKUP BATT EMPTY
FAN STOP
WIRELESS-RF
EOM
BOS
EOS
CANNOT REC
CANNOT PLAY
COMM ERROR
TEXT MEMO
TEXT MEMO INVALID
MARK ON/OFF
SHOT MARK INVALID
UPDATING
USB DEVICE
USB HOST
THUMBNAIL OPEN
1394 INITIAL ERROR
PROXY REC P2&SD
PROXY REC P2
NEAR END (SD)
EOM (SD)
PROXY CARD ERROR
SD CARD WRITE ERR
CANNOT DISP IN VF
TC REGEN
SLOT SEL
SLOT SEL INVALID
DIR NG CARD
SLOT1/2/3/4/5
RUN DOWN CARD
SLOT1/2/3/4/5
12:59:59:20
TCR 12:59:59:20
(V)UBG AB CD EF 00
(V)UBR 12 34 56 78
CTL –1:59:59:20
DZ a 2/ a 3/ a 4
EX
Something abnormal is happening to the internal computer communications
or reference signal. No further recording or playback can be performed. ¢¢
is replaced with an error code.For more information, see [Error Codes]
(page 148).
P2 card has been removed while being accessed (recorded, played back, or
formatted), and subsequent operation is disabled.
An error has occurred while recording data to or playing data from a P2
card. In the actual indication the ¢ is replaced by the slot number of the P2
card that triggered the error.
Something abnormal is happening to video and/or audio being recorded.
Backup battery needs replacing.
The fan is locked and halted.
RF signal from the wireless receiver is degraded.
P2 card has no free space.
Playback position is at the start of all the clips.
Playback position is at the end of all the clips.
The P2 card is not recordable. Detailed information is provided on the
FUNCTION screen of MODE CHECK. See the relevant section of the
MODE CHECK indication area.
Clip cannot be played back perhaps because no P2 card is loaded, or the
P2 card contains no clips.
Displayed when disconnection between microcomputers continues for a
specified period or longer.
Text memo has been added.
Text memo has not been successfully added.
Shot mark been added or deleted. For information on shot marks, see [ Shot
Mark Function ] (page 41).
This is displayed when shot marks cannot be added.
Clip information is being updated. Playback operation disabled.
AJ-HPX2000 is in USB DEVICE mode. When communication is disabled,
the indication blinks.
Indicates that the camera-recorder is set to the USB HOST mode. When the
external hard disk is not successfully recognized, then the indication blinks.
Thumbnail is being manipulated.
Displayed when the connection of the DVCPRO/DV connector is abnormal
(when AJ-YAD800G is attached).
Displayed when proxy recording on either the P2 card or the SD memory
card starts (when AJ-YAX800G is attached, the PROXY REC item on the
VF INDICATOR2 screen is turned on).
Displayed when proxy recording on the P2 card starts (when AJ-YAX800G is
attached, the PROXY REC item on the VF INDICATOR2 screen is turned on).
When the remaining free space on the SD Memory card drops below one
minute during proxy recording, the message is displayed (when AJ-
YAX800G is attached).
Displayed when full capacity is reached during proxy recording on the SD
memory card (when AJ-YAX800G is attached).
Displayed when proxy recording stops because of failure on either the video
encoder card or the stream.(when AJ-YAX800G is attached).
Displayed when a failure occurs on the SD memory card during proxy
recording, and only recording on the SD memory card stops.(when AJ-
YAX800G is attached).
No return video, playback, or externally input video can be output to the
viewfinder.
The RET button was pressed to regenerate the time code as the time code
for the last clip recorded on a P2 card.
This blinks while the recording slots of P2 cards are switched after pressing
the USER switch where the SLOT SEL function is assigned.
This is displayed if the recording slots of P2 cards cannot be switched when
the USER switch where the SLOT SEL function is assigned is pressed.
This is displayed when the recording starts or completes while a P2 card with
an irregular directory arrangement is inserted or data are recorded after
inserting an irregular P2 card.
This is displayed when the recording starts or completes with an expired P2
card or when data are recorded after inserting an expired P2 card.
TCG (time code generator value)
TCR (time code reader value)
UBG VUBG (User bits generator value)
UBR VUBR (User bits reader value)
Displays CTL count.
Magnification of the digital zoom when the unit is in digital zoom mode.
Lens extender used.
Status