Panasonic AJ-HPX2000 Operating Instructions Manual page 21

32.
DVCPRO/DV connector
This is an in/output connector for video, voice, and
data that comply with the IEEE1394 standard.
Notes
Power is not supplied from the unit.
Be absolutely sure to bear the following points in
mind when connecting the IEEE1394 cable (DV
cable).
Ensure that the connections with other devices are
made on a 1:1 basis.
When a DV cable has been connected to the DV
connector, do not apply any strong external force
as this may damage the connector.
When error code 1394 E-92 (1394 INITIAL
ERROR) appears, disconnect the connecting
cables and re-connect them or turn off the
camera-recorder's power and turn it back on.
Ensure that the unit and all of the connected
devices are each grounded (or connected to a
common ground) before use.
If it is not possible to ground the unit and devices,
turn off the power of the unit and of all the
connected devices
disconnecting the IEEE1394 cable.
When the unit is to be connected to a device
equipped with a 4-pin type of connector, connect
the unit's connector (6-pin type) first.
When connecting the unit
with a PC equipped with
a 6-pin type ofconnector,
connect the 1394 cable
as dictated by the shapes
of the 1394 connectors.
Bear in mind
inserting a plug the wrong way round may damage
the unit.
When the unit is used in AVC-Intra format, image/
voice signals cannot be output/input through the
DVCPRO/DV connector.
33.
REMOTE (remote control) connector
The remote control
accessory) is connected here.
34.
OPTION SLOT
Attach the video encoder
optional). For information about the installation and
proxy recording, see the AJ-YAX800G instruction
manual.
before connecting or
6-pin type
4-pin type
that
unit AJ-RC10G (optional
card (AJ-YAX800G,
Parts and their Functions ： Shooting and Recording/Playback Functions Section
35.
SD memory card insertion slot
An SD memory card (optional accessory) is inserted
here. SD memory cards are used for recording and
accessing the menu settings of cameras and the lens
files, uploading metadata,
(optional).
<Cautions in using SD memory cards>
Use the unit by inserting an SD memory card that is
compliant with the SD standard or the SDHC standard.
MultiMediaCards cannot be used. (Bear in mind that
taking pictures may no longer be possible if you do use
them.)
If you intend to use miniSD cards in camera-recorder,
always install the adapter specially designed for
miniSD cards. (The unit will not work properly if only
the miniSD card adapter is installed. Make sure that
the card has been installed in the adapter before using
it.)
Use of Panasonic's SD memory cards and miniSD
cards is recommended. Be sure to format cards using
camera-recorder.
To format SD memory cards using a personal
computer, download the dedicated software from the
support site.
Any SD memory card with the following capacities (8
MB to 2 GB) and any 4 GB SDHC memory card can
be used with the unit.
8 MB 16 MB
128 MB 256 MB
2 GB 4 GB (SDHC)
To record proxy (optional), use an SD memory card with
a capacity of 256 MB, 512 MB, 1 GB, or 2 GB labeled
"High Speed" or use a 4 GB SDHC memory card.
For the latest information not available in the operating
Instructions, visit the P2 Support Desk at the following
Web sites.
https://eww.pavc.panasonic.co.jp/pro-av/
The SDHC card conforms to a new standard for memory
cards with a large capacity of more than 2 GB which was
established by the SD Association in 2006.
The SD card logo is a registered trademark.
MMC (MultiMediaCard) is a registered trademark of Infineon
Technologies AG.
36.
BUSY (operation mode display) lamp
This lamp indicates the active status of the SD
memory card.
It stays illuminated when the card is active.
Note
While the lamp is on, do not insert or remove the card.
and proxy recording
32 MB 64 MB
512 MB 1 GB
21