Korg PA1X User Manual page 370

366 Effects
Mono – Mono Chain
066: Comp - P4EQ
(Compressor – Parametric 4-Band EQ)
This effect combines a mono-type compressor and a four-band
parametric equalizer. You can change the order of the effect con-
nection.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Compressor
+
Comp
Output Level
Right
Envelope - Control
[C] Sensitivity
a
Sets the sensitivity
[C] Attack
Table , "Sets the attack level," on page 330
b
Output Level
Sets the compressor output level
[E] Trim
c
Sets the parametric EQ input level
[E] Band1 Cutoff [Hz]
Sets the center frequency of Band 1
Q
d
Sets the bandwidth of Band 1
Gain [dB]
Sets the gain of Band 1
[E] Band2 Cutoff [Hz]
Sets the center frequency of Band 2
Q
e
Sets the bandwidth of Band 2
Gain [dB]
Sets the gain of Band 2
[E] Band3 Cutoff [Hz]
Sets the center frequency for Band 3
Q
f
Sets the bandwidth of Band 3
Gain [dB]
Sets the gain of Band 3
[E] Band4 Cutoff [Hz]
Sets the center frequency for Band 4
Q
g
Sets the bandwidth of Band 4
Gain [dB]
Sets the gain of Band 4
Routing
h
Switches the order of the compressor and parametric EQ connection
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 330
Src
i
Table , "Selects the modulation source of the effect balance," on page 330
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 330
Wet / Dry
Routing
Parametric 4Band EQ
Trim
Wet / Dry
1...100
☞
Fx:002
1...100
☞
Fx:002
0...100
☞
Fx:002
0...100
20...1.00kHz
0.5...10.0
☞
Fx:006
–18...+18dB
50...5.00kHz
0.5...10.0
☞
Fx:006
–18...+18dB
300...10.00kHz
0.5...10.0
☞
Fx:006
–18...+18dB
500...20.00kHz
0.5...10.0
☞
Fx:006
–18...+18dB
CMP → PEQ, PEQ → CMP
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
067: Comp - ChoFlng
(Compressor – Chorus/Flanger)
This effect combines a mono-type compressor and a chorus/
flanger. You can change the order of the effect connection.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Compressor
EQ Trim LEQ HEQ
+
Comp
Output Level
Right
Envelope - Control
[C] Sensitivity
a
Sets the sensitivity
[C] Attack
Table , "Sets the attack level," on page 330
b
Output Level
Sets the compressor output level
[C] EQ Trim
c
Table , "Sets the EQ input level," on page 330
[C] Pre LEQ Gain [dB]
Table , "Sets the gain of Low EQ," on page 330
d
Pre HEQ Gain [dB]
Table , "Sets the gain of High EQ," on page 330
[F] Delay Time [msec]
e
Sets the delay time
[F] LFO Frequency [Hz]
Sets the LFO speed
f
LFO Waveform
Selects LFO Waveform
[F] Depth
Sets the depth of LFO modulation
g
Feedback
Sets the feedback amount
[F] Cho/Flng Wet/Dry
Sets the effect balance of the chorus/flanger
h
Output Mode
Selects the output mode for the chorus/flanger
Routing
i Switches the order of the compressor and chorus/flanger connection
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 330
Src
j
Table , "Selects the modulation source of the effect balance," on page 330
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 330
h: Output Mode, i: Routing
When Wet Invert is selected, the right channel phase of the cho-
rus/flanger effect sound is inverted. This creates pseudo-stereo
effects and adds spread.
However, if a mono-input type effect is connected after this
effect, the left and right sounds may cancel each other, eliminat-
ing the chorus/flanger effects.
When "Routing" is set to FLNG→CMP, "Output Mode" will be set
to Normal.
Wet / Dry
Routing
Chorus/Flanger
Chorus/Flanger
Normal
+ Output Mode
–
Wet Invert
Feedback
Cho/Flng Wet / Dry
Wet / Dry
LFO: Tri / Sine
1...100
☞
Fx:002
1...100
☞
Fx:002
0...100
☞
Fx:002
0...100
–15...+15dB
–15...+15dB
0.0...50.0msec
0.02...20.00Hz
Triangle, Sine
0...100
–100...+100
☞
Fx:020
–Wet...–2:98, Dry, 2:98...Wet
☞
Fx:010, 020
Normal, Wet Invert
☞
CMP → FLNG, FLNG → CMP
☞
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100