Korg PA1X User Manual page 359

042: Auto Reverse
This effect records the input signal and automatically plays it in
reverse (the effect is similar to a tape reverse sound).
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
+
Auto Reverse
Rec/Reverse Play
Right
D-mod
D -mod
Envelope Control
Input
Envelope Select
Rec Mode
a
Sets the recording mode
Reverse Time [msec]
b
Sets the maximum duration of the reverse playback
Envelope Select
Selects whether the start and end of recording is controlled via the modula-
tion source or the input signal level
c
Src
Selects the modulation source that controls recording when Envelope Select
is set to D-mod
Threshold
d Sets the recording start level when Envelope Select is set to Input
Response
e
Sets the speed of the response to the end of recording
Direct Mix
f
Selects how a dry sound is mixed
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 330
Src
g
Table , "Selects the modulation source of the effect balance," on page 330
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 330
a: Rec Mode, b: Reverse Time
When "Rec Mode" is set to Single, you can set up to 1320msec for
"Reverse Time. "If recording starts during the reverse playback,
the playback will be interrupted.
When "Rec Mode" is set to Multi, you can make another record-
ing during the reverse playback. However, the maximum Reverse
Time is limited to 660msec.
If you wish to record a phrase or rhythm pattern, set "Rec Mode"
to Single. If you record only one note, set "Rec Mode" to Multi.
The "Reverse Time" parameter specifies the maximum duration
of the reverse playback. The part in excess of this limit will not be
played in reverse. If you wish to add short pieces of the reverse
playback of single notes, make the "Reverse Time" shorter.
Rec Reverse Rec
Input
Rec Mode = Single
Rec Mode = Multi
Reverse Time
c: Envelope Select, c: Src, d: Threshold
These parameters select the source to control the start and end of
recording.
Wet / Dry
Direct
Mix
Control
Wet / Dry
Single, Multi
20...1320msec
☞
D-mod, Input
☞
,
Off...Tempo
☞
0...100
☞
0...100
☞
Fx:031
Always On, Always Off, Cross Fade
☞
Fx:031
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Rec Mode/Reverse Time
Reverse
Envelope Select = Input
Time
Reverse Time
When "Envelope Select" is set to D-mod, the input signal will be
recorded only when the value of the modulation source selected
by the Src parameter is 64 or higher.
When "Envelope Select" is set to Input, the input signal will be
recorded only when its level exceeds the Threshold level.
When recording is completed, reverse playback starts immedi-
ately.
043: L/C/R Delay
This multitap delay outputs three Tap signals to the left, right,
and center respectively. You can also adjust the left and right
spread of the delay sound.
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left
☞
Input Level D-mod
+
High Damp Low Damp
Input Level D-mod
Right
L Delay Time [msec]
Sets the delay time of TapL
a
Level
Sets the output level of TapL
C Delay Time [msec]
Sets the delay time of TapC
b
Level
Sets the output level of TapC
R Delay Time [msec]
Sets the delay time of TapR
c
Level
Sets the output level of TapR
Feedback (C Delay)
Sets the feedback amountof TapC
Src
d
Selects the modulation source of the TapC feedback amount
Amt
Sets the modulation amount of the TapC feedback amount
High Damp [%]
Sets the damping amount in the high range
e
Low Damp [%]
Sets the damping amount in the low range
Input Level Dmod [%]
Sets the modulation amount of the input level
f
Src
Selects the modulation source for the input level
Spread
g
Sets the width of the stereo image of the effect sound
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 330
Src
h
Table , "Selects the modulation source of the effect balance," on page 330
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 330
e: High Damp [%], e: Low Damp [%]
These parameters set the damping amount of high range and
low range. The tone of the delayed sound becomes darker and
lighter as it feeds back.
g: Spread
This parameter sets the pan width of the effect sound. The stereo
image is widest with a value of 50, and the effect sound of both
channels is output from the center with a value of 0.
Effects 355
ER/Delay
Wet / Dry
L Delay
Level
C Delay
Spread
Level
Feedback
R Delay
Level
Wet / Dry
0...1360msec
0...50
0...1360msec
0...50
0...1360msec
0...50
–100...+100
Off...Tempo
–100...+100
0...100%
0...100%
–100...+100
☞
Fx:037,
Off...Tempo
☞
Fx:037
0...50
☞
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
☞
☞