Korg PA1X User Manual page 337

The Attack and Release parameters set the Gate attack time and
release time.
Output Level
Threshold
Dry
Wet
Wet
Attack
e: Delay Time
This parameter sets the delay time of the Gate input. If the sound
has a very fast attack, increase the delay time so that the signal
will be input after the Gate is opened. This will preserve the
attack part of the sound.
006: OD - Hi Gain Wah
(Overdrive/Hi.Gain Wah)
This distortion effect utilizes an Overdrive mode and a Hi-Gain
mode. Controlling the wah effect, the 3-band EQ, and the amp
simulation will allow you to create versatile distortion sounds.
This effect is suitable for guitar and organ sounds.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Mode: Overdrive / Hi-Gain
Drive
Pre Low-cut
+
Driver
Wah
Output Level
Direct Mix
Right
D -mod
Wah
Switches Wah on/off
Src
a Selects the modulation source that switches the Wah on and off
Sw
Selects the switching mode for the modulation source that switches the Wah
on and off
Wah Sweep Range
Sets the range of Wah
b
Wah Sweep Src
Selects the modulation source that controls the Wah
Drive Mode
c
Switches between overdrive and hi-gain distortion
Drive
Sets the degree of distortion
d
Pre Low-cut
Sets the low range cut amount of the distortion input
Output Level
Sets the output level
Src
e
Selects the modulation source for the output level
Amt
Sets the modulation amount of the output level
Gate - Threshold
Louder
Input Level
Gate - Attack / Release
Threshold
Attack=1
Release=1
Attack=100
Release=100
Release
Wet / Dry
3 Band PEQ
Amp Simulation
Wet / Dry
Off, On
☞
,
Off...Tempo
Toggle, Moment
☞
–10...+10
☞
,
Off...Tempo
☞
Overdrive, Hi-Gain
1...100
0...10
☞
0...50
☞
,
Off...Tempo
–50...+50
Low Cutoff [Hz]
Sets the center frequency for Low EQ (shelving type)
f
Gain [dB]
Table , "Sets the gain of Low EQ," on page 330
Mid1 Cutoff [Hz]
Sets the center frequency for Mid/High EQ 1 (peaking type)
Q
g
Sets the band width of Mid/High EQ 1
Gain [dB]
Sets the gain of Mid/High EQ 1
Mid2 Cutoff [Hz]
Sets the center frequency for Mid/High EQ 2 (peaking type)
Q
h
Sets the band width of Mid/High EQ 2
Gain [dB]
Sets the gain of Mid/High EQ 2
Direct Mix
Sets the amount of the dry sound mixed to the distortion
i
Speaker Simulation
Switches the speaker simulation on/off
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 330
Src
j
Table , "Selects the modulation source of the effect balance," on page 330
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 330
a: Wah
The Wah parameter switches the wah effect on/off.
a: Sw
This parameter sets how the wah effect is switched on and off via
the modulation source.
When "Sw" = Moment, the wah effect is usually turned off. It is
turned on only when you press the pedal or operate the joystick.
When a value for the modulation source is less than 64, "off"
speed is selected, and when the value is 64 or higher, "on" is
selected.
When "Sw" = Toggle, the wah effect is switched between on and
off each time you press the pedal or operate the joystick.
The switch will be turned on/off each time the value of the
modulation source exceeds 64.
b: Wah Sweep Range, b: Wah Sweep Src
This parameter sets the sweep range of the wah center fre-
quency. A negative value will reverse the direction of sweep. The
wah center frequency can be controlled by the modulation
source specified in the "Wah Sweep Src" parameter.
d: Drive, e: Output Level
The degree of distortion is determined by the level of input sig-
nal and the setting of "Drive". Raising the "Drive" setting will
cause the entire volume level to increase. Use the "Output Level"
parameter to adjust the volume level. The "Output Level" param-
eter uses the signal level input to the 3-Band EQ. If clipping
occurs at the 3-Band EQ, adjust the "Output Level" parameter.
d: Pre Low-cut
☞
Cutting the signal in the low range before it is input to the Dis-
tortion will create a sharp distortion.
g: Q, h: Q
These parameters set the bandwidth of each equalizer. The
higher the value, the narrower the band becomes.
Effects 333
Filter/Dynamic
20...1.0kHz
–18...+18dB
300...10.00kHz
0.5...10.0
☞
–18...+18dB
500...20.00kHz
0.5...10.0
☞
–18...+18dB
0...50
Off, On
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100