ATTO Technology FibreBridge 2370E Installation And Operation Manual page 44

RestoreConfiguration
Restores configuration to either the default configuration or the
configuration last saved into non-volatile memory. The saved
option undoes any changes made since the last save.
RestoreConfiguration [Default | Saved]
Route
Assigns a Fibre Channel address to a target destination device.
If you try to map a new SCSI BTL to the same FC LUN, the new
BTL overwrites the previous map. Using the delete identifier
removes the map from its table. If
enabled, overwriting an existing map requires secondary
confirmation.
Route FC [fp] [lun] [SCSI <sb st sl> | Bridge | Delete ]
RouteDisplay
Displays a list of Fibre Channel to SCSI address mappings on
the FibreBridge.
When LogicalUnitAddressing
RouteDisplay FC <fp> <lun>
When LogicalUnitAddressing
RouteDisplay SCSI <sb st sl>
SaveConfiguration
Many commands require a SaveConfiguration command to
be executed as indicated by the return Ready. *. When you
invoke a SaveConfiguration command, the current
configuration is permanently saved in the FibreBridge and the
new configuration becomes the active configuration. If a
firmware restart is required to make the requested change
permanent, you are asked to confirm the restart. You can
override this request by indicating the override value on the
command line. You may make several changes through
commands before implementing the restart, but once you have
restarted the FibreBridge, all the command changes created
before the restart and save are implemented. If you select the
restart option, the FibreBridge executes its complete start up
cycle.
SaveConfiguration <Restart | NoRestart>
SCSIDomainValidation
Runs domain validation tests on the SCSI system which may
detect problems with SCSI cables, termination or damaged
transceivers. Disable VirtualDriveResponse
the test If tape drives are attached to the FibreBridge, ensure
they are loaded with media: media is not overwritten with this
test. Reboot the FibreBridge after running this test.
SCSIDomainValidation
xi
ATTO Technology Inc. FibreBridge Installation and Operation Manual
VerboseMode has been
is disabled:
is enabled:
before running
SCSIInitID
Specifies or reports the SCSI initiator ID on the specified SCSI
port as found in NVRAM. All maps coinciding with the user-
specified SCSIInitID are destroyed after the command
completes.
Default: 7
set SCSIInitID [sb [0-15] ]
get SCSIInitID [sb]
SCSIPortBusSpeed
Controls the transfer rate at which the FibreBridge negotiates
with its SCSI devices. Valid options are Fast SCSI, Ultra SCSI,
Ultra 2 SCSI, Ultra160 SCSI and Ultra320 SCSI.
Default: ultra320
set SCSIPortBusSpeed [sb [ fast | ultra | ultra2 | ultra160
| ultra320]
Requires a SaveConfiguration command
get SCSIPortBusSpeed [sb]
SCSIPortList
Returns a list of available SCSI ports and their current status.
Valid status values are OK and Failed
SCSIPortList
SCSIPortReset
Resets the specified SCSI bus.
SCSIPortReset [sb]
SCSIPortResetOnStartup
Specifies if the SCSI port should be reset on power-up.
Default: enabled
set SCSIPortResetOnStartup [sb [enabled | disabled] ]
Requires a SaveConfiguration command
get SCSIPortResetOnStartup [sb]
SCSIPortSyncTransfer
Specifies whether synchronous SCSI transfers should be
negotiated with devices on the specified SCSI port.
Default: enabled
set SCSIPortSyncTransfer [sb ] [enabled | disabled]
Requires a SaveConfiguration command
get SCSIPortSyncTransfer [sb]
SCSIPortTermination
Configures/reports the SCSI internal termination of the SCSI
port identified on the FibreBridge. Enabling termination allows
the FibreBridge to act as a terminator at the end of a SCSI
chain.
Default: enabled
set SCSIPortTermination [sb] [enabled | disabled]
Requires a SaveConfiguration command
get SCSIPortTermination [sb]