LG-Nortel iPECS-50 Administrator And Maintenance Manual page 63

IPECS Release 5
Admin & Maintenance
Button ATTRIBUTE/DISPLAY
1
01-02 CO NAME DISPLAY
(1:ON/0:OFF) : OFF
2
01-02 CO NAME ASSIGN
............
3
01-02 METERING UNIT
00:NONE (00-11)
4
01-02 LINE DROP(CPT)
(1:ON/0:OFF) : OFF
5
01-02 DISA ACCT CODE
(1:ON/0:OFF) : OFF
6
01-02 MOH: (0-3)
MUSIC 1 (1)
7
01-02 CO DIAL TONE
(1:ON/0:OFF) : OFF
8
01-02 CO RBACK TONE
(1:ON/0:OFF) : OFF
9
01-02 CO ERROR TONE
(1:ON/0:OFF) : OFF
10
01-02 CO BUSY TONE
(1:ON/0:OFF) : OFF
11
01-02 DISA CO ACCESS
(1:ON/0:OFF) : OFF
12
01-02 FLASH TMR
(000-300 10 ms) : 050
13
01-02 OPEN LOOP
(00-20 100ms) : 04
14
01-02 ICLI DT TMR
(00-20 SEC) : 00
15
01-02 SMS OUTGOING
(1:EN/0:DIS) : DISABLE
16
01-02 SMS RCV STATION
STA : ....
Table 2.3.5.2-2 CO/IP ATTRIBUTES II (PGM 142)
DESCRIPTION
The IP Phone display can indicate the CO
Line/IP channel number or a twelve (12)-
character name, if assigned.
Each CO Line and the IP group can be
assigned a twelve (12) character name for
display purposes, see Table 2.1.2-1 for
character entry sequence.
Selects the call-metering signal from the
PSTN to indicate call cost, refer to Table
2.3.5.2-5.
Each CO Line can be programmed to
disconnect if a second dial tone is detected.
[not supported]
With DISA ACCT CODE "ON", users will be
required to enter an Authorization code.
Enter codes in Authorization Codes Table -
PGM Code 227-.
A held call can be connected to one (1) of
three (3) possible audio sources while on
Hold as Music-on-Hold (MOH).
ISDN Lines may provide a digital signal rather
than actual tones. In this case, the iPECS
can provide the tones. If the ISDN provides
the tones for buttons 7 to 10, the tone is
"ON", for an iPECS system-generated tone,
the ISDN tone is set to "OFF".
Permits DISA users access to the VoIP
facilities of the system.
This entry sets the duration of a Flash on the
CO Line.
This entry sets the duration of open loop that
will be recognized as a "Disconnect Signal".
When a call is received, the system may use
the ICLID (Incoming Caller ID) to route the
call. The system will delay routing a call for
this timer while awaiting ICLID. Enter a 00 to
disable ICLID routing.
Each CO line can be assigned to support
PSTN SMS.
When a PSTN SMS is received, the system
delivers the message to the assigned station.
2-44
Issue 5.0
RANGE DEFAULT
0: OFF OFF
1: ON
12
characters
00~11 00
0: OFF OFF
1: ON
0: OFF ON
1: ON
0: none 1
1: Int/Ext 1
2: Ext 2
3: VSF
0: OFF ON
1: ON
0: OFF OFF
1: ON
0: OFF OFF
1: ON
0: OFF OFF
1: ON
0: OFF OFF
1: ON
(000-300) 050
10 msec 500 msec
(00-20) 04
100 msec
(00-20) 00
1 sec
0: Disable Disable
1: Enable
Station ....