Did/Disa Destination - LG-Nortel iPECS-50 Administrator And Maintenance Manual

IPECS Release 5
Admin & Maintenance
Button DISPLAY
18
CO RING ON TMR(100ms)
(1-9) : 2
19
ELAPSED CALL TMR(sec)
(060-900) : 180
20
WEB PWD GUARD TMR (min)
(001-999) : 005
Button ATTRIBUTE/DISPLAY
1
FWD NO ANS TMR(sec)
(000-600) : 015
2
DID/DISA NO ANS(sec)
(000-255) : 20
3
VSF USR RECORD(sec)
(000-999) : 060
4
VSF VALID USER MSG(sec)
(0-9) : 4
5
DOOR OPEN TMR(100ms)
(05-99) : 20
6
ICM DIAL TONE TMR(sec)
(01-20) : 10
7
INTER DIGIT TMR(sec)
(01-20) : 05
8
MSG REMINDER TONE(min)
(00-60) : 00
9
PAGE TIME OUT TMR(sec)
(000-255) : 015
10
PAUSE TMR(sec)
(1-9) : 3
11
SOFT AUTO RLS TMR(sec)
(01-30) : 10
12
VM PAUSE TMR(100 msec)
(01-90) : 30
DESCRIPTION
This timer sets the 'ON' time of the incoming
ring cycle for the Ring Detect circuitry of the
system to recognize an incoming call.
Users can receive a periodic tone indicating
the length of an outgoing call. This timer sets
the time before and between the tones. Note
Call Time Tone must be enabled in
112-btn 1.
If no data packets are received during a Web
Admin connection for the Guard time, a
password check will be initiated by the
system.
Table 2.3.6.20-2 SYSTEM TIMERS II (PGM 181)
DESCRIPTION
When a user activates No-Answer Forward,
calls will ring for this duration before the calls
are forward. The Station No-Answer Forward
timer
PGM CODE
A DID/DISA call to a station will forward to the
DID/DISA Destination assigned in
167 should this timer expire before the call is
answered.
This timer sets the maximum duration allowed
for the User Greeting in the system's basic
Voice Mail.
This timer sets the minimum duration allowed
for a voice mail message in the system's
basic VSF Voice Mail. Messages shorter
than this period are not stored.
This timer sets the minimum contact closure
time required to activate the contact assigned
as a door open contact.
If a user goes off-hook on the Intercom and
takes no action for this timer, the user will
receive error tone.
This timer sets the maximum allowed time
between user dialed digits. At expiration, the
user will receive error-tone.
An iPECS Phone user will receive periodic
reminder tones of a message waiting at
intervals based on this timer.
Determines the maximum duration of a page
after which the caller and Page Zone are
released.
A Timed pause of this duration is used in
Speed Dial and during other automatically
dialed digits sent to the PSTN.
When a Soft Key is used on the 6000 or 7000
series iPECS Phone, after expiration of this
timer, the display will return to the previous
display.
When the system sends a "Pause" to Voice
Mail using In-band signals, the Pause interval
is defined by this timer. Not available in the
USA.
2-85
PGM CODE
123 will take precedence.
PGM CODE
Issue 5.0
RANGE DEFAULT
1~9 2
(100 msec.)
060~900 180
(seconds)
001~999 5
(minutes)
RANGE DEFAULT
000~600 015
(seconds)
00~99 00
(seconds)
000~999 60
(seconds)
0~9 4
(seconds)
05~99 20
(100 msec.)
01~20 10
(seconds)
01~20 05
(seconds)
00~60 00
(minutes)
000~255 15
(seconds)
1~9 3
(seconds)
1~30 10
(seconds)
1~90 30
(100 msec.)