Tunturi T50 Owner's Manual page 10

belt .and stand steadily where you normally run on the
belt.
2. Take hold of the horizontal handlebar and push the
belt with your feet so that it slides back and forth. The belt
should move softly and evenly, without a sound.
3. If you notice jerky movement or if the belt will not slide
check for lubrication by sliding your hand under the belt.
Lubricate the running deck according to the following
instructions:
1. Fold up the running deck and lock it.
2. Cut off the tip of the bottle cap.
3. Position the lubricant bottle between the belt and the
board
4. Try to reach the bottle as far into the center of the
running belt as possible and point the tip of the bottle
towards the running belt.
5. Squeeze the lubricant bottle to dispense half of the
bottle.
6. Move the running belt half of a revolution and repeat
steps 4 and 5.
7. Fold down the running deck into it's normal position. Use
treadmill for your training session or allow the treadmill to
run for at least 5 minutes.
ALIGNING THE RUNNING BELT
adjustments as needed. The belt should run in the
center of the treadmill. Alignment is not usually
needed, provided
• the treadmill is placed on an even, solid and
horizontal surface and the belt is correctly tensioned
• the alignment of the belt is correct
It is, however, possible for the belt to be pushed to
one side due to the user's running style (e.g. more
weight on one foot). The alignment of the belt is
adjusted by turning the two bolts at the back of the
treadmill.
ALIGN THE BELT ACORDING TO THE FOLOWING
INSTRUCTIONS:
1. Turn the power switch on and increase the
treadmill's speed to 5 km/h (3 mph).
2. If the belt drifts to the left, turn the left
adjustment bolt 1/4 turn clockwise and the right
adjustment bolt 1/8 turn anti-clockwise. If the belt
drifts to the right, turn the right adjustment bolt 1/4
turn clockwise and the left adjustment bolt ¼ turn
anti-clockwise.
3. If the belt remains centered the adjustment is
correct. If not, continue to make small adjustments
as above until the belt is correctly aligned. If the belt
is allowed run across to one side for long periods of
time the edges of the belt may be damaged and the
treadmill may not continue to operate correctly. Any
damage to the belt caused by the lack of necessary
adjustment will not be covered by the warranty.
ADJUSTING THE BELT TENSION
The belt must be tensioned if it begins to slip on
the rollers. In normal use, however, keep the belt
as loose as possible! The belt tension is adjusted by
turning the same screws as used for aligning the
running belt. If turning the screws will not effect the
belt tension, please contact your local Tunturi dealer.
1. Increase the treadmill's speed to 5 km/h (3 mph).
2. Turn both adjustment screws an equal amount, ¼
turn clockwise.
3. Try to slow the belt down by holding onto the
handrails and braking as you walk (as if you were
walking downhill). If the belt slips, turn another
1/4 turn and repeat the test. When braking heavily
the belt may slip. If the belt keeps slipping despite
repeated adjustments, please contact your local
Tunturi dealer.
MALFUNCTIONS
NOTE! Despite continuous quality control, defects
and malfunctions caused by individual components
may occur in the equipment. In most cases it's
unnecessary to take the whole device in for repair,
as it's usually suffi cient to replace the defective
part. Always give the model, serial number of
your equipment and in case of malfunctions also
conditions of use, nature of malfunction and any
error code.
When you encounter unusual behavior from the
treadmill, simply turn the power switch off, wait 1
minute and turn the power switch on to reset the
treadmill. This should clear incidental errors and
ready the treadmill for normal operation again. If
after you have reset the treadmill by turning the
power switch off and on again, and the treadmill
is still not operational, contact your local Tunturi
dealer for service.
If you require spare parts, always give the model,
serial number of your equipment and the spare part
number for the part you need. The spare part list
is at the back of this manual. Use only spare parts
mentioned in the spare part list.
ERROR CODES
The user interface will display information about
operational faults.
E1: Speed sensor error. Unplug the electrical cord
from the wall outlet and from the treadmill, wait
1 minute and turn the power switch on again. If
treadmill recovers to normal operation, you may
continue to use the treadmill. Otherwise, call the
dealer for service.
E6, E7: Lift motor error. Unplug the electrical cord
from the wall outlet and from the treadmill, wait
1 minute and turn the power switch on again. If
treadmill recovers to normal operation, you may
continue to use the treadmill. Otherwise, call the
dealer for service.
PROTECTIVE CIRCUIT
The machine will shut off when the electricity
load is above the machine's capacity. To restart the
machine, please follow the procedure below:
A. Unplug the power cord from the machine's
socket.
B. Push in the safety switch.
C. Replug the power cord into the machine's socket.
10