Table of Contents
Advertisement
»Basic settings, model«
... To this end, switch to the line "Module".
BASIC SETTINGS, MODEL
Model name
Starlet
Info
2345g/090911
Stick mode
Module
HoTT
n/a
n/a
SEL
BD1 BD2 BD3 BD4
Note:
After confi rmation of the model selection in the base
screen, if you confi rm the message appearing in the
screen for a few seconds ...
BIND. N/A
OK
... with a tap on the
SET
key of the right touch pad,
this line will be accessed automatically.
The line "Module" initiates a binding process between
model memory and receiver, as described in detail on
page 88. Otherwise, you cannot address the receiver.
Afterward, use the selection key of the left or right
four-way pad to move up to the fi rst line and begin
with actual model programming in the "Model name"
line. Now give the model memory an appropriate
name, ...
BASIC SETTINGS, MODEL
Starlet
Model name
Info
2345g/090911
Stick mode
HoTT
n/a
Module
n/a
SEL
BD1 BD2 BD3 BD4
310 Programming examples - Helicopter models
(page 84 ... 92)
... which must be assembled from characters available
on the second page of the "Model name" line:
!"#$%&'()
@ACDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_
`abcdefghijklmnopqrstuvwxyz{|}~
¢ÇüéâäàåçêëèïîìÄÅÉæÆôöòûùÖÜ
1
n/a
n/a
Model name
After entering the "Model name", the settings
adopted from »General basic settings« for "Stick
mode" and "DSC Output" are to be checked and
changed as necessary for the given memory location.
The entry fi eld in the "Info" line can be used if needed
for a notice of up to 15 characters in length. This
notice will then be helpful in the selection of models
and so on.
Another option is to be activated in the
"Autorotation" line. Even if you are not an advanced
pilot, the autorotation switch should at least be set as
an emergency shutoff switch for the motor.
Do this by selecting the "Autorotation" line with a
brief tap on the center
pad, activate the switch assignment, assign a 2-way
switch, e.g. "2", an put it in its "ON" position.
BASIC SETTINGS, MODEL
RF transmit
RF range test
DSC Output
Autorotation
1
n/a
n/a
The selected switch should be in a location on the
transmitter which is easily within reach – without letting
loose of a joystick – e.g. above the pitch joystick.
+,–./0123456789:;
?
Starle
SET
key of the right touch
on
99s
PPM10
2I
SET
SET
Note:
More more information about the setting of this
"emergency shutoff", see the beginning of the second
following double-page.
Another tip:
Make a habit of giving all switches a common switch-
on direction; then a quick glance over the transmitter
prior to the fl ight should suffi ce – all switches off.
Setting options for the "Autorotation C1 position",
"Motor stop", "Marking" and "Stick warning" are not
yet of particular interest ...
... and the "Auto Trim" line should only be assigned
to a switch if "Initial trimming" is to be performed
on the helicopter in the context of a trimming fl ight.
Following such a fl ight, this switch should be erased
once again, for reasons of safety.
Additional settings specifi c to helicopters are made in
the menu ...
»Helicopter type«
In the "Swashplate type" line, select control for
swashplate or pitch function. In this example:
"3Sv(2rol)".
The "Linearis. swashpl." line is not yet of interest.
In the "Rotor direction" line, it is established whether
the rotor – as viewed from above – turns to the right
(clockwise) or left (counter-clockwise). In other words,
whether it rotates counterclockwise or clockwise. In
this example "right".
Check the default for "Pitch min", which was adopted
from »General basic settings«, to confi rm that the
entry "front" or "rear" is in keeping with personal
preferences or should be changed.
(page 98)
Advertisement
Table of Contents
