Related Manuals for GRAUPNER S1031
Summary of Contents for GRAUPNER S1031
- Page 1 Manual mz-4 2 channel HoTT 2,4 GHz transmitter No. S1031 www.modellmarkt24.ch; www.modellmarkt24.ch; www.modellmarkt24.de www.modellmarkt24.de...
- Page 2 www.modellmarkt24.ch; www.modellmarkt24.ch; www.modellmarkt24.de www.modellmarkt24.de...
-
Page 3: Table Of Contents
Index Introduction ................. 4 Service Centre ..............4 Intended use ............... 5 Package content ..............5 Technical Data ..............5 Symbols explication ............6 Safety notes ................ 6 Description of the transmitter ........... 8 Control elements on the transmitter ........8 Transmitter power supply .......... -
Page 4: Introduction
Introduction Thank you very much for purchasing the Graupner mz-4 HoTT transmitter. Read this manual carefully to achieve the best results with your transmitter and first of all to safely control your models. If you experience any trouble during operation, take the instructions to help or ask your dealer or Graupner Service Centre. -
Page 5: Intended Use
Read through this entire manual before you attempt to install or use the transmitter. Graupner/SJ constantly works on the development of all prod- ucts; we reserve the right to change the item, its technology and equipment. Target group The product is not a toy. -
Page 6: Symbols Explication
Symbols explication Always observe the information indicated by this warning sign. Particularly those which are additionally marked with the CAU- TION or WARNING. The signal word WARNING indicates the poten- tial for serious injury, the signal word CAUTION indicates possibil- ity of lighter injuries. - Page 7 Only use the components and spare parts that we recommend. Always use matching, original Graupner plug-in connections of the same design and material. Make sure that all of the plug-in connections are tight. When dis- connecting the plug-in connections, do not pull the cables.
-
Page 8: Description Of The Transmitter
Description of the transmitter Control elements on the transmitter LED 1, yellow (Motor cut-off display, model memory) LED ON: Motor OFF Model memory 1, LED 1 blinks 1x each 2 seconds. LED 2, red (status and binding display, warnings) ON: bound* Trim - (trim and servo travel setting) Trim + (trim and servo travel setting) CUT OFF/BIND (binding / motor cut-off) -
Page 9: Transmitter Power Supply
Transmitter power supply Installing transmitter batteries Remove the battery case cover on the back side of the transmitter. Insert the battery according to the correct polarity. (See figure in the battery case) Removing transmitter batteries If the transmitter is not going to be used for a long time, the batteries or accumulators must be removed from the device. -
Page 10: Range Test
Range test Switch the mz-4 HoTT transmitter and your receiver on. Hold the "CUT OFF/ BIND" (5) button pushed for about 5 sec The range test is active for 90 seconds. At the begin the LED 2 will light up twice red with two signal tones. -
Page 11: Trigger Switch
Trigger switch In the model memory are stored the optimal settings for the related model. Thus makes controlling the model easier. The trigger-switch (8) activates one optional setting while pushed. Also this setting is preprogrammed. For example the throttle limit is removed and the servo travel is increased. The setting are however free settable. -
Page 12: Servo Reverse Channel 2
Setting channel 1 throttle travel 1. Move the control stick (6) completely forward. 2. In this position push and hold the control stick switch (6). 3. Now reduce with the trim button (3) - or increase with the trim button (4) + the throttle travel. For the trigger-switch (8) setting proceed as follows, push the gimbal trigger switch (8) Servo reverse channel 2... -
Page 13: Fail Safe
Fail safe Through this function you can store in the receiver for each channel the settings which will be recalled in case of connection interrup- tions between transmitter and receiver. The - (3) trim button is for channel 1 The + (4) trim button is for channel 2 The LED 1 indicates by pushing the trim buttons (3) and (4) the related status. -
Page 14: Led Status Display
(2) Declaration of conformity S1031 mz-4 HoTT Graupner/SJ declares that the product is conform to EU norms. EN 300 440-1 V1.6.1; EN 300 440-2 V1.4.1 3.2; EN 301 489-1 V1.9.2; EN 301 489-3 V1.6.1 3.1 EN 62479: 2010 3.1 EN 60950-1:2006 +A11:2009+ A1:2010+A12:2011+A2:2013 www.modellmarkt24.ch;... -
Page 15: Notes On Environmental Protection
The cur- rent version can be found on the Internet at www.graupner.de the relevant product page. In addition, the company Graupner has no responsibility or liability for any errors or inaccuracies that may appear in construction or operation manuals. - Page 16 www.modellmarkt24.ch; www.modellmarkt24.ch; www.modellmarkt24.de www.modellmarkt24.de 16 / 16 S1031_HB_V1...
Need help?
Do you have a question about the S1031 and is the answer not in the manual?
Questions and answers