GRAUPNER mc-32 Programming Manual page 113

Column 2, "typ"
Similar to the previously described »Stick mode«
menu, this column can be used to defi ne whether
further settings for the given input are to have a
"GL(obal)" or a "PH(ase-specifi c)" effect. Do this by
using the selection keys of the left or right touch pad
to select the desired input 5 through 16 in the column
labeled "TYP".
I5 GL fr --- 0% +100%
Thr6 GL fr --- 0% +100%
fr ---
Gyr7 GL 0% +100%
I8 GL fr --- 0% +100%
Normal
TYP SEL Offset – travel +
"GL": The settings for the input in question affect
all fl ight phases programmed (if any) and
thus act "globally" on the model memory in
question.
"PH": The settings for this input take effect per
fl ight phase and must therefore be confi gured
separately for each fl ight phase.
Note:
See page 142 for more information about fl ight
phases.
Column 3, "Transmitter control/switch
assignment"
Using the  selection keys of the left or right touch
pad to select an input: I5, Thr6, Gyr7, I8 ... 15 or
Tl16.
Transmitter control assignment
Use the selection keys to move into the column
labeled SEL. After completing the activation of
transmitter control assignment by tapping the center
SET key of the right touch pad , the message shown
below will appear in the display:
I5 GL fr
Thr6 GL fr
Gyr7 GL fr
I8 GL fr
Normal
TYP SEL
Now actuate the desired transmitter control: The
+100% 0.0 0.0
notice window will disappear and the designation
+100% 0.0 0.0
of the selected transmitter control will appear in the
transmitter control assignment window.
+100% 0.0 0.0
+100% 0.0 0.0
I5 GL S11 ---
Thr6 GL fr
–time+
Gyr7 GL fr
I8 GL fr
Normal
TYP SEL
Alternatively, the center
pad can be tapped for a second time while the notice
window, see above, is still on the display:
I5 GL fr
Thr6 GL fr
Gyr7 GL fr
E8 GL fr
Normal
TYP SEL
Now use the selection keys of the left or right touch
pad to select the desired input out of the list if the
respective plug-in location on the transmitter board
is occupied or switch the entry to "fr" if the input is to
be decoupled from a transmitter control. In this case,
or even when a non-existent transmitter control is
assigned, the servo corresponding to this input will be
--- 0% +100% +100% 0.0 0.0
--- Move desired 0% +100% +100% 0.0 0.0
--- control adj. 0% +100% +100% 0.0 0.0
--- 0% +100% +100% 0.0 0.0
Offset – travel + –time+
0% +100% +100% 0.0 0.0
--- 0% +100% +100% 0.0 0.0
--- 0% +100% +100% 0.0 0.0
--- 0% +100% +100% 0.0 0.0
Offset – travel + –time+
SET key of the right touch
--- 0% +100% +100% 0.0 0.0
--- 0% +100% +100% 0.0 0.0
--- 0% +100% +100% 0.0 0.0
---
0% +100% +100% 0.0 0.0
Offset – travel + –time+
Detail program description - Control adjust | Helicopters
in its neutral position and can only be controlled via
mixers.
I5 GL S11 --- 0% +100%
Thr6 GL fr --- 0% +100%
Gyr7 GL fr --- 0% +100%
I8 GL fr --- 0% +100%
Nor mal
TYP SEL Offset – travel +
Switch assignment
If the input is to be actuated like a switch module, the
input can alternatively be assigned to a switch.
A simple switch can be used to switch back and forth
between two limit values, for example motor On/Off.
A 2-way momentary or toggle switch, see appendix,
achieves the same effect as a 2-channel switch
module, for example motor Off/Half/Full.
Use the selection keys to move into the column
above the switch symbol label. Briefl y tap the
center SET key of the right touch pad to activate the
option for assigning a switch.
I5 GL fr --- 0% +100%
Thr6 GL fr Move desired switch --- 0% +100%
Gyr7 GL fr to ON position --- 0% +100%
I8 GL fr (ext. switch: ENTER) --- 0% +100%
Nor mal
TYP SEL Offset – travel +
Actuate the desired toggle switch from its "OFF"
to its "ON" position or, for a 3-way switch,
beginning from its middle position, assign a switch
direction – preferably the "second" direction. This
means, if a function is to be switched on by moving
the switch forward two positions, i.e. away from the
pilot, then begin from the switch's middle position and
move the switch away from the pilot.
+100% 0.0 0.0
+100% 0.0 0.0
+100% 0.0 0.0
+100% 0.0 0.0
–time+
+100% 0.0 0.0
+100% 0.0 0.0
+100% 0.0 0.0
+100% 0.0 0.0
–time+
113