Table of Contents
Advertisement
In a manner similar to "Pre-set stick mode, in this
»General basic settings« menu the selection made
for the "Pre-set DSC Output" line will determine which
of the four possible modulation types will be adopted
as the default variant for a newly initialized model
memory.
If necessary, use the selection keys of the left
or right touch pad to switch to the "DSC Output" line
then, with a brief tap on the center
right touch pad, activate the value window:
G ENE R AL BASI C SE T T I NG S
Owners name
H-J Sandbrunner
H-J Sandbrunner
Pre-set stick mode
Pre-set modulation
Pre-set DSC Output
Now a choice can be made from among the four
possible modulation types: "PPM10", "PPM16",
"PPM18" and "PPM24", with the selection keys of the
right touch pad. Another tap on the center
the right touch pad will conclude the entry.
A simultaneous tap on the or keys of the
right touch pad (CLEAR) will reset this option back to
"PPM10".
Pre-set Pitch min
(only relevant to helicopter models)
In a manner similar to the previously described
options "Stick mode" and "DSC Output", enter
the preferred actuation direction for the throttle/
pitch joystick on this line so the choice will already
be present by default for model memories newly
initialized in the future. The functionality of all other
helicopter program options (to the extent they affect
throttle and/or pitch) are dependent on this setting; in
other words the throttle curve, idle trim, Channel 1
tail rotor mixer, etc.
This means:
"fwd.":
minimum front pitch setting, the pitch
joystick (C1) points away from the pilot.
"back": minimum rear pitch setting, the pitch
joystick (C1) points towards the pilot.
A simultaneous tap on the or keys of the
right touch pad (CLEAR) will set this option to "rear".
SET
key of the
Note:
The C1 joystick's control direction for "Throttle min
front/rear" in the fi xed-wing program can be changed
individually in the »Model type« menu.
1
Contrast, upper display / lower display
HoTT
In assure optimal legibility of
PPM10
under all weather and temperature conditions, their
SEL
contrast settings can be adjusted separately.
Contrast for the forward display, located between the
switch panels, is adjusted by selecting the "Top LCD
contrast" line with the selection keys of the left or right
touch pad then briefl y tapping on the center
SET
key of
of the right touch pad.
G E N E R A L B A S IC S ET T IN G S
Pre-set DSC Output
Pre-set Pitch min.
Top LCD contrast
Bottom LCD contrast
Now display contrast can be adjusted in the value
fi eld displayed in inverse video within a range of ±20
by using the selection keys of the right touch pad.
Contrast for the rear display, located between the
mc-32
HoTT displays
touch pads, is adjusted by selecting the "Bottom LCD
contrast" line with the selection keys of the left or right
touch pad then briefl y tapping on the center
of the right touch pad.
SET
key
Pre-set DSC Output
Pre-set Pitch min.
Top LCD contrast
Bottom LCD contrast
PPM10
rear
0
Now display contrast can be adjusted in the value
fi eld displayed in inverse video within a range of ±20
0
by using the selection keys of the right touch pad.
SEL
#01
H-J Sandbrunner
4.1V
0
Detail program description - Basic settings
RX–S QUA: 100%
RX–S STR: 100%
RX–dBm:
33dBm
TX–dBm:
33dBm
L–PACK:
10ms
RX–VOLT:4.8
TMP
CH OUTPUT TYPE:ONCE
R-LOW V:4.6
+22°C
RX–S QUA: 100%
RX–S STR: 100%
RX–dBm:
33dBm
TX–dBm:
33dBm
L–PACK:
10ms
RX–VOLT:4.8
TMP
CH OUTPUT TYPE:ONCE
R-LOW V:4.6
+22°C
GEN ER AL BASI C SET T IN G S
PPM10
rear
0
0
SEL
Graubele
Stop watch
0:00h
Flight tim
0:00h
K78
V
RX VOLT:4.9V
M
0
0
SET
key
0:00.0
0:00.0
0
259
Advertisement
Table of Contents
