Table of Contents
Advertisement
e.
To
facilitate
reinstallation,
mark
the
location
of
to the
canopy section.
the trim
strip
clips.
NOTE
f.
Remove
the
rivets
from
around
the
windshield.
When riveting
the
windshield
in place,
install
g.
Remove
the
windshield.
the trim
strip
clips
in
the
same
locations
as
marked
in
step "e"
of
the
windshield
removal
NOTE
procedure.
i.
Secure
the
glareshield
angles
in place
with
at-
Due
to the
windshield
being
sealed,
consider-
taching
screws,
nuts
and spacers.
able effort
may be
required
to
break
the
wind-
shield
loose from
the
canopy section,
j. Position
the
defroster
duct and secure
in place
with
the
attaching
screws.
DEFROSTER
DUCT
ATTACHING
SCREW
k. Install
the trim
strips.
GLARESHIELD
1.
Install
the
glareshield
and outside air
temperature
ANGLE
,
gage
(if removed).
m.
Clean
and
paint
as necessary,
DEFROSTER
DUCT
GLARESHIELD
,
STORM
WINDOW
REMOVAL
AND INSTALLATION
a.
Remove
the
attaching
bolt
from
the
storm
win-
dow
sleeve assembly.
b.
Remove
the
hinge pin,
c. Installation
is
accomplished
by reversing
the
a-
bove
procedure.
GLARESHIELD
FORWARD
L.
H.
WINDOW
REMOVAL
ANGLE
ATTACHING
WINDSHIELD
SCREW
-FRAME
a.
Remove
the
storm
window.
GLARESHIELD
ANGŒ
b. Remove
the
upholstery
panels as required
to
gain
Figure
4-4.
Windshield
(Typical)
access
to the
window
frame.
c.
Remove
the trim
strip from around
the
inside
of
WINDSHIELD
INSTALLATION
the
window.
a. Clean
the
sealer from
the
canopy section where
d.
Remove
the
screws and nuts attaching
the
storm
the
old windshield
was removed
using
toluol.
window
strike
to the
window
frame.
b.
Trim
the tooling tabs
from
the
windshield,
place
e.
To
facilitate
reinstallation,
mark
the
location
of
the
windshield
in position
and
mark
the
areas where
the trim
strip clips,
material
must
be removed
from
the
windshield
to
ob-
tain
a proper
fit.
f.
Remove
the
rivets
from around
the
window.
c.
Remove
the
windshield
and
trim
off excess
ma-
g.
Remove
the
window.
terial
as determined
in
step "b".
FORWARD
L. H. WINDOW
INSTALLATION
d.
Place
the
windshield
in
position and eleco
in
place
using
the
pilot holes
provided.
a.
Clean
the
sealer from
the
canopy section
where
the
old
window was removed
using
toluol.
e.
Back
drill
the
windshield
frame using
the
exist-
ing holes
in
the
canopy section as a guide.
b.
Place
the
window
in
position and
mark
the
areas
where
material
must
be
removed
to
obtain
a proper
f.
Remove
the
windshield,
burr
all
holes
and apply
fit.
Presstite
#576
sealer
to the
windshield
frame
where
it makes
contact with
the
canopy section.
c.
Remove
the
window and
trim
off
the
excess ma-
terial
as determined
in
step
"b".
g.
Place
the
windshield
in
position and cleco in
place.
d.
Place
the
window
in position
and cleco
in place
h.
Using
AN470AD4
rivets,
secure
the
windshield
using
the
pilot
holes provided.
4-18
Advertisement
Table of Contents
Troubleshooting
