Cabin Door Window Removal; Cabin Door Window Installation; Center Window Removal And Installation; Aft Window Installation - Beechcraft TRAVEL AIR 95 Shop Manual

e.
Back drill
the
window frame
using
the
existing NOTE
holes in
the
canopy section as a guide.
To eliminate
the
possibility
of
the
door being
f. Remove
the
window,
burr all holes
and
apply
warped;
the
door must be closed and latched
Presstite
2576
sealer
to
an area
approximately 1 2 when drilling
the
attaching
holes and securing
inch
wide
on
the
canopy section where
the
old
sealer
the
window in place,
was removed.
e. Back drill the
window frame using
the
existing
g.
Place
the
window in position
and cleco
in place, holes in
the
door as a guide,
h.
Using AN470AD4
rivets, secure
the
window
to
f. Remove
the
window, burr all
holes
and apply
the
canopy section. Presstite
#576 sealer to
an area approximately 1/2
inch wide on
the
door
where
the
old
sealer
was re-
NOTE moved.
When riveting
the
window in place, install g.
Place
the
window in position
and
cleco
in place,
the trim
strip clips in
the
same
locations
as marked in step "e" of
the
window removal h. Using AN470AD4
rivets,
secure
the
window
to
procedure,
the
door,
i. Install
the
trim
strips. NOTE
j. Attach
the storm
window
strike
to the
window When riveting
the
window in place,
install
frame.
the trim
strip clips
in
the same locations
as marked
in step
"d"
of
the
window removal
k. Install
the
storm
window. procedure.
1. Clean
and
paint
as necessary.
i. Install
the trim
strip.
m. Reinstall
the
upholstery
panels.
j. Clean
and paint
as necessary.
k. Reinstall
the
center
upholslery panel.
CABIN DOOR WINDOW
REMOVAL
1. Reinstall
the
inboard
door
handle,
ash tray
and
a.
Remove
the
inboard door handle, ash
tray
and
arm
rest.
arm rest.
CENTER WINDOW REMOVAL
AND INSTALLATION
b.
Remove
the
center upholstery panel.
a. Remove
the
emergency
release pin.
c. Remove
the trim
strip around
the
inside of
the
window.
b. Remove
the
hinge pin.
d. To
facilitate
reinstallation, mark
the
location
c.
Installation
is
accomplished
by reversing
the
a-
of
the trim
strip clips.
bove procedure.
e.
Remove
the
rivets around
the
window.
NOTE
f.
Remove
the
window.
Some
hand forming may be required
to
obtain
a
proper
fit,
AFT WINDOW REMOVAL
CABIN DOOR WINDOW INSTALLATION
a. Remove
the
upholstery
panel
along bottom of
the
a. Clean
the
sealer
from
the
door where
the
old window.
window was removed using
toluol.
b. Remove
the
royalite
molding
around
the
window.
b. Place
the
window in position and mark
the
areas
where material must
be
removed
to
obtain
a proper
c.
Remove
the top,
bottom and forward retaining
fit.
angles
by removing
the
attaching screws.
c. Remove
the
window and
trim
off excess
material
d.
Remove
the
window.
as determined in step
"b".
AFT WINDOW INSTALLATION
d. Place
the
window in position and
eleco
in place
using
the two
pilot holes on
the aft side of
the
window a. Clean
the sealer from the canopy section
where
frame.
the old window was removed
using
toluol.
4-19