Table of Contents
Advertisement
1/2" OVERLAY PANEL DIMENSIONS
For a more custom appearance, overlay panels may be
installed on trimmed models. The overlay panel must be
secured to a 1/4" thick backer panel which slides into the
trim. A spacer panel 0.10" thick must be placed between the
overlay and backer panel.
Assemble the panels with glue and screws:
• Center the spacer panel on the backer panel, left to right
and top to bottom. Secure the panels with glue.
• Refer to the following chart for locating the backer panel to
the overlay panel. Secure the overlay panel to the backer
panel with glue and screws. Screws must be countersunk
into the backer panel.
Hinge Side
C
Freezer
Back
Backer with
Overlay Panel
Assembly
D
A
B
A
IMPORTANT NOTE – DISPENSER MODELS
The refrigerator is supplied with 3 dispenser trims; 2 for standard
installation and 1 for flush installation. The flush installation trim
is designed to fit a total panel thickness of 0.85" or 0.75".
• If the panel is less than 0.75" a noticeable gap may be created
around the dispenser trim.
• If the panel is more than 0.85" the dispenser trim cannot be
secured to the door.
Panel Dimensions
E
15-3/8"
F
9-5/8"
IMPORTANT NOTE: Maximum total weight for the assembled panels:
•
Fresh food door panel – 75 lbs.
Design Guide - Flush Installation
C
Fresh Food
Back
SxS Fresh Food
SxS Freezer
SxS Grille
D
B
36" Side-by-Side
Fresh Food
1/4" Backer Panel
68-3/8" x 18-9/16"
.10" Spacer Panel
67" x 17-9/16"
1/2" Overlay Panel
68-5/8" x 20-7/8"
42" Side-by-Side
Fresh Food
1/4" Backer Panel
68-3/8"x 24-9/16"
.10" Spacer Panel
67" x 23-9/16"
1/2" Overlay Panel
68-5/8" x 26-7/8"
48" Side-by-Side
Fresh Food
1/4" Backer Panel
68-3/8" x 29-9/16"
.10" Spacer Panel
67" x 25-9/16"
1/2" Overlay Panel
68-5/8" x 28-7/8"
•
Freezer door panel – 53 lbs.
Door
1/2"
Overlay
Panel
1/4"
.10"
Backer
Spacer
Panel
.250" + .10" + .50" = .850" Total Panel Thickness
Grille Back
C
A
B
D
A
B
2-1/16"
1/16"
2-1/16"
1/16"
2-1/16"
2-1/16"
1-15/32"*
*2" for 36" models
• The overlay panel must be constructed according to the
specifications shown to achieve the correct total thickness.
• Cut the dispenser opening after the backer, spacer and
overlay panels have been assembled.
See Dispenser Trim Fit Example, page 28.
Freezer
68-3/8" x 14-9/16"
33-7/8" x 9"
67" x 13-9/16"
33" x 8-3/8"
68-5/8" x 16-7/8"
38" x 11-3/16"
Freezer
68-3/8" x 14-9/16"
39-7/8" x 9-1/2"
67" x 13-9/16"
39" x 8-5/8"
68-5/8" x 16-7/8"
44" x 11-3/16"
Freezer
68-3/8" x 18-9/16"
45-7/8" x 9-1/2"
67" x 17-9/16"
45" x 8-5/8"
68-5/8" x 20-7/8"
50" x 11-3/16"
•
Grille Panel – 18 lbs.
26
C
D
1/8"
1/8"
1/8"
1/8"
7/32"
Grille
Dispenser Cutout Position
E
17-23/32"
Grille
Dispenser Cutout Position
E
17-23/32"
Grille
Dispenser Cutout Position
E
17-23/32"
F
3-3/8"
F
3-3/8"
F
5-3/8"
Advertisement
Table of Contents
