Monogram ZIS48N Custom Options Manual And Installation Instructions
Monogram ZIS48N Custom Options Manual And Installation Instructions

Monogram ZIS48N Custom Options Manual And Installation Instructions

48" built-in refrigerators

Advertisement

Quick Links

These Monogram built-in refrigerators are
designed to be customized with decorator
door and grille panels. Field installed
panels are required.
Factory installed trim will accommodate
1/4" thick custom panels or optional
®
Lexan
and Stainless Steel panel kits.
Optional trim kits allow an even broader
range of custom appearance options.
Read this booklet carefully to accomplish the
desired appearance and to insure a trouble free
installation.
This booklet contains information and
illustrations to demonstrate custom
possibilities. Custom door and grille panel
sizes vary to accommodate the kit being
used. Dimensions for each application are
included and can be faxed or sent to the
cabinet manufacturer so that the panels can
be constructed accurately.
®
GE Monogram
48" Built-In Refrigerators
Custom
Options Guide
and
Installation
Instructions
With Custom Panel Dimensions
and Trim Kit
Installation Instructions
Models:
ZIS48N
ZISW48D
ZISB48D

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ZIS48N and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Monogram ZIS48N

  • Page 1 ® GE Monogram 48" Built-In Refrigerators Custom Options Guide Installation Instructions With Custom Panel Dimensions and Trim Kit Installation Instructions Models: These Monogram built-in refrigerators are ZIS48N designed to be customized with decorator door and grille panels. Field installed ZISW48D panels are required.
  • Page 2: Table Of Contents

    Proper installation is the responsibility of the installer. Product failure due to improper installation is not ATTENTION covered under the GE Appliance Warranty. See the Use & Care Guide for warranty information. • Il ne faut utiliser cet appareil que pour l’usage pour lequel il a été...
  • Page 3: Cutout And Product Dimensions

    Design Information 48" Built-In Refrigerator Advance Planning Flush or Semi-Flush Enclosure Installations 3/4" 0" True Flush Installation Semi-Flush Installation In a flush installation, These refrigerators the refrigerator doors can also be installed will align evenly with the semi-flush into an enclosure front face of adjacent cabinet using the minimum cutout doors.
  • Page 4: Installation Between Base & Wall Cabinets

    Panels are cut to examples and trim kit descriptions. size and ready to install. These panel kits must be ordered separately. Model Black White Stainless ZIS48N ZWBP48 ZWWP48 ZWSP48 ZISW48D ZWWP48D ZWSP48D ZISB48D ZWBP48D...
  • Page 5: Advance Planning, Exterior Appearance Options

    Design Information 48" Built-In Refrigerator These refrigerators are designed to be customized with Advance You should: planning decorator door and grille panels. Field installed custom 1. Select the appearance option. exterior door and grille panels are required. 2. Order the trim kit(s) for that option. appearance 3.
  • Page 6: Custom Panel Dimensions

    Custom Panel Dimensions 48" Built-In Refrigerator Front View ZIS48N (not to scale) (Non-dispenser) Side View (not to scale) 47" Case Width Design Information 24 3/4" 48" Overall Width Cutout dimensions, clearances and side panel sizes are 12 1/4" max determined by the many installation options available.
  • Page 7 Custom Panel Dimensions 48" Built-In Refrigerator Custom Door Panel Dimensions Using Standard Trim ZIS48N (non-dispenser) 1/4" thick panels Standard Trim with 1/4" Panels • 1/4" Panels: Cut panels to size. Panels secured to 1/4" thick backing • Custom handles with 1/4" door panels require Trim Kit ZKH1 (or ZKHSS1 for tubular-stainless steel handles).
  • Page 8 Custom Panel Dimensions 48" Built-In Refrigerator Custom Door Panel Dimensions ZIS48N (non-dispenser) Using Trim Kit ZKT48 • The ZKT48 trim kit provides for the installation of 3/4" 3/4" thick panel with standard handle custom door and grille panels, using the standard full- length handle.
  • Page 9 Custom Panel Dimensions 48" Built-In Refrigerator ZIS48N (non-dispenser) Custom Door Panel Dimensions Using Trim Kits ZKT48 3/4" thick panel • ZKT48 and ZKHT1 installed together provides for the installation of 3/4" custom door and grille panels, with custom handle using a custom handle, of your choice. Order ZKHTSS1 for tubular stainless-steel handles.
  • Page 10: Zisw48D, Zisb48D

    Custom Panel Dimensions 48" Built-In Refrigerator ZISW48D (white dispenser) ZISB48D (black dispenser) Front View (not to scale) Side View Design Information (not to scale) 47" Case Width Cutout dimensions, clearances and side panel sizes are 24 3/4" 48" Overall Width determined by the many installation options available.
  • Page 11 Custom Panel Dimensions 48" Built-In Refrigerator Custom Door Panel Dimensions Using Standard Trim ZISW48D (white dispenser) 1/4" thick panels ZISB48D (black dispenser) Standard Trim with 1/4" Panels Panels secured to 1/4" thick backing • 1/4" Panels: Cut panels to size. •...
  • Page 12 Custom Panel Dimensions 48" Built-In Refrigerator ZISW48D (white dispenser) Custom Door Panel Dimensions Using Trim Kit ZKT48 ZISB48D (black dispenser) 3/4" thick panel with standard handle • The ZKT48 trim kit provides for the installation of 3/4" and/or ZWCD2 custom collar trim custom door and grille panels, using the standard full- length handle.
  • Page 13 Custom Panel Dimensions 48" Built-In Refrigerator ZISW48D (white dispenser) Custom Door Panel Dimensions Using Trim Kit ZKT48 ZISB48D (black dispenser) 3/4" thick panel with custom handle • ZKT48 and ZKHT1 installed together provides for the and/or ZWCD2 custom collar trim installation of 3/4"...
  • Page 14: Side Panel Or Filler Options

    Custom Panel Dimensions 48" Built-In Refrigerator Side Panel or Filler Options For All Monogram Built-In Refrigerators (not to scale) Side panels must be used whenever the sides of the refrigerator will be exposed. 24 3/4" 1/2" to 3/4" Side Panels 23 9/16"...
  • Page 15 Installation 48" Built-In Refrigerator • Tinsnips to cut banding • Bucket • 7/16" open-end wrench • Drill and appropriate Tools • Stepladder • Level • #2 Phillips screwdriver bits Required • Appliance Hand Truck • Stubby Phillips • 7/16" socket with 3" •...
  • Page 16: Installation Instructions

    Installation 48" Built-In Refrigerator Step 1 CAUTION Remove Packaging Refrigerator is much heavier at the top than at the bottom – be careful when moving. When using a hand truck, handle from side only. PRUDENCE Le réfrigérateur est beaucoup plus lourd en haut qu'en bas.
  • Page 17 Installation 48" Built-In Refrigerator Step 3 • Side panels are not required when the refrigerator is • If you choose to use 1/4" side panels, they should be Install installed into an enclosure. Skip this step if you are inserted into the case trim as illustrated. Fasten the Side Panels installing in an enclosure.
  • Page 18 Installation 48" Built-In Refrigerator Step 6 If you are using 3/4" thick custom panels, SKIP THIS Install 1/4" STEP. See Custom Panel Dimensions pages for panel door panels sizes with ZKT48 trim kit and other kits. Refer to trim kit installation instructions in this booklet.
  • Page 19 Installation 48" Built-In Refrigerator Step 7 WARNING Soffit Block OPTION 1 Secure ANTI-TIP PRECAUTIONS refrigerator The refrigerator is heavy at the top and must be at the top secured to prevent the possibility of tipping forward. ATTENTION PRECAUTIONS CONTRE LES BASCULEMENTS Le réfrigérateur est beaucoup plus lourd en haut et il faut le maintenir en place pour éviter la possibilité...
  • Page 20 Installation 48" Built-In Refrigerator Step 9 • Connect refrigerator power cord plug to properly Connect grounded receptacle, accessible through the top right power side of the grille opening. • Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are Step 10 If you are using 3/4"...
  • Page 21 ZKH1 Trim Kit (For 1/4" Panels) Support for Custom Handles These instructions are divided into 2 options: Tools and materials Option 1—For non-dispenser and dispenser models required: using custom collar trim. • #2 Phillips screwdriver Option 2—For dispenser model using the standard •...
  • Page 22 ZKH1 Trim Kit (For 1/4" Panels) Support for Custom Handles Option 1 Installation Step 2 Door Extrusion Locate position of handles 3/4" Min. 1-1/2" Max. Handle must be located Note: 3/4" to 1-1/2" from edge of extrusion. • Again, with both doors closed, check the location of •...
  • Page 23 ZKH1 Trim Kit (For 1/4" Panels) Support for Custom Handles Option 1 Installation Step 3 Assemble panel, extrusion and handle Screw Extrusion Decorator Door Decorator Panel Door Panel Handle 3/4" Min. 1-1/2" Max. Door Handle • Remove the door extrusions and door panels. •...
  • Page 24 ZKH1 Trim Kit (For 1/4" Panels) Support for Custom Handles • Carefully remove the Phillips head screws from the OPTION 2 For dispenser model door handle endcaps, top and bottom. using full-width • Open door to 90°. Remove the screws from the trim full-length aluminum handle of the freezer door.
  • Page 25 ZKH1 Trim Kit (For 1/4" Panels) Support for Custom Handles Option 2 Installation Step 4 • Drill clearance holes through the handle bracket and Install the dispenser trim. custom handle • Install screw(s) long enough to pass through the handle bracket, dispenser trim and into the custom handle.
  • Page 26: Grille Panel Frame Adjustment

    ZG2 Trim Kit Grille Panel Frame Adjustment FOR 83", 83-1/2" • This kit provides optional side trim pieces for the original grille frame to fit 83", 83-1/2" or 84-1/2" AND 84-1/2" installation heights. INSTALLATION HEIGHTS To change grille panel size: •...
  • Page 27 ZKT48 Trim Kit 3/4" Custom Panels Tools and materials These instructions are divided into 2 options: Option 1—For non-dispenser and dispenser models required: using custom collar trim. • #2 Phillips screwdriver Option 2—For dispenser model using the standard • Stubby Phillips screwdriver full-width trim.
  • Page 28 ZKT48 Trim Kit 3/4" Custom Panels • Carefully remove the Phillips head screws from the OPTION 1 For non-dispenser door handle top endcaps. model • Open door to 90°. or dispenser model • Remove the Phillips head screws from the full-length using custom handles.
  • Page 29 ZKT48 Trim Kit 3/4" Custom Panels Option 1 Installation Back Side Door Panel Step 3 Apply panel Dimension A support brackets ZKT48–8-3/4" Hinge Support Bracket Support Bracket Dimension B ZKT48–11-7/8" Bottom Edge Bottom Edge Freezer Panels Fresh Food Panel • Position support bracket on freezer panel, •...
  • Page 30 ZKT48 Trim Kit 3/4" Custom Panels Option 1 Installation Step 5 The refrigerator is shipped with the top case trim Adjust secured at the 83" refrigerator height. grille panel • Loosen 2 screws on both sides and raise the top case height trim to meet soffit height, from 83"...
  • Page 31 ZKT48 Trim Kit 3/4" Custom Panels OPTION 2 • Carefully remove the Phillips head screws from the For dispenser freezer door handle endcap, if present. model using • Open freezer door to 90°. full-width • Remove the Phillips head screws from the full-length trim handles.
  • Page 32 ZKT48 Trim Kit 3/4" Custom Panels Step 4 Install panels • Install the lower panel by slipping tabs into the slots • Place the upper panel onto the top of the dispenser on the underside of the dispenser trim. with tabs inserted into the slots. •...
  • Page 33 ZKHT1 Trim Kit (For 3/4" Panels) Support for Custom Handles These instructions are divided into 2 options: Tools and materials Option 1—For non-dispenser and dispenser models required: using custom collar trim. • #2 Phillips screwdriver Option 2—For dispenser model using the standard •...
  • Page 34 ZKHT1 Trim Kit (For 3/4" Panels) Support for Custom Handles Step 1 Temporarily mount door panels • Secure the panel to the trim temporarily by driving • Place the prepared 3/4"custom door panels on the bottom trim with support bracket tabs inserted into 2 screws through the back side of the trim at the top.
  • Page 35 ZKHT1 Trim Kit (For 3/4" Panels) Support for Custom Handles Option 1 Installation Step 3 • Remove the door extrusions and door panels. Assemble panel, • Drill 1/16" pilot hole through extrusion. extrusion • Drill clearance holes through the panel and extrusion. and handle •...
  • Page 36 ZKHT1 Trim Kit (For 3/4" Panels) Support for Custom Handles Option 1 Installation OPTION 2 1-13/16" 1-13/16" For dispenser Optimal final Note: model using 1/4" Max. Back Side Back Side appearance depends on careful full-width routing depth. Do not exceed trim Handle Side Handle Side...
  • Page 37 ZKHT1 Trim Kit (For 3/4" Panels) Support for Custom Handles Option 2 Installation • Drill clearance holes through the handle bracket and Step 2 Install the dispenser trim. custom handle • Install screw(s) long enough to pass through the handle bracket, dispenser trim and into the custom handle.
  • Page 38 ZKHSS1 for 1/4" Panels Tubular Stainless Steel Handles This kit provides for the installation of Stainless Steel custom Note: It is best that 2 people install this kit. handles on 1/4" thick decorator door panels. The door extru- sions allow these custom handles to be secured to the door structure, rather than to the custom panels.
  • Page 39 ZKHSS1 for 1/4" Panels Tubular Stainless Steel Handles • Cut a piece of corrugated to use as a pad to protect Step 2: Match the panel finish. Use 1/2" thick section of plywood to Handle Extrusions protect flooring when drilling. Note: Be sure to orient to Handle •...
  • Page 40 ZKHSS1 for 1/4" Panels Tubular Stainless Steel Handles If you are installing these handles onto Stainless Steel Step 2A: • Align extrusion to pencil mark(s) as shown in Step 2. panels: Mark each screw hole location with pencil. Use extreme caution if you are drilling through •...
  • Page 41 ZKHSS1 for 1/4" Panels Tubular Stainless Steel Handles Step 4A: Install Handles and Panels Door Handle STAINLESS Extrusion STEEL PANELS Screw Spacer Ring Stainless Panel 1/4" Handle Stainless Corrugated Panel For Stainless Panels: • Press foam pads against steel doors to temporarily •...
  • Page 42 ZKHTSS1 for 3/4" Panels Tubulor Stainless Steel Handles This kit provides for the installation of Stainless Steel This kit must be used in combination with ZKT36, ZKT42 custom handles on 3/4" thick decorator door panels. or ZKT48 trim kit. The door extrusions allow these custom handles to be The ZKT trim kits provide the framework to support 3/4"...
  • Page 43 ZKHTSS1 for 3/4" Panels Tubulor Stainless Steel Handles Step 1: • Carefully remove the phillips head screws from the Remove door handle top endcaps, if present. Handles • Open doors to 90°. Remove the screws from the full- length handles of both doors. •...
  • Page 44 ZKHTSS1 for 3/4" panels Tubular Stainless Steel Handles • Place a handle standoff on each attachment post Step 3: along the handle. Position the screw hole on the Install Standoffs standoff to point to the floor. onto Handles • Install set screws into the bottom of each standoff, using the Allen wrench provided.
  • Page 45 ZKHTSS1 for 3/4" Panels Tubular Stainless Steel Handles Step 5 For models with full width dispenser trim and 2 piece Install freezer panels: Assembled It is best that 2 people perform this step. Panels • Carefully, lift the assembled panel to the case trim. (continued) Hold both panels so they do not twist the extrustion.
  • Page 46: 3/4" Thick Custom Panels

    ZWCD2 Trim Kit Custom Dispenser Collar Tools and materials required: • #2 Phillips screwdriver • Drill and appropriate bits • Custom door panels • Safety glasses Parts List: contents A. Collar trim (Both black and white trim included) B. Top bracket C.
  • Page 47 ZWCD2 Trim Kit Custom Dispenser Collar Cut dispenser The use of this custom collar trim requires that the hole hole and rout for dispenser be located and cut very accurately . 3/4" 12 1/16" door panel door panels must be routed on all 4 sides of the dispenser cutout.
  • Page 48 Note: While performing installations described in this book, safety glasses or goggles should be worn. To obtain specific information concerning any ® Monogram product or service, call GE Answer Center consumer information service at 800.626.2000–any time, day or night. For Monogram local service in your area, call 1-800-444-1845.

This manual is also suitable for:

Zisw48dZisb48dZisw48dZisb48d

Table of Contents