3/4' Overlay Panel Dimensions "Sss - Monogram ZIS360N Installation Instructions Manual

Design Guide
3/4" OVERLAY PANEL DIMENSIONS
For a more custom appearance, overlay panels may be
installed on trimmed models. The overlay panel must
be secured to a 1/4" thick backer panel which slides
into the trim. A spacer panel 0.10" thick must be \
placed between the overlay and backer panel. .
Assemble the panels with glue and screws.
¢ Center the spacer panel on the backer panel, left to i
right and top to bottom. Secure the panels with glue.
| 3a"
| Overlay
| Panel
Overlay Panel
NOTE: Left-to-right offset
\
¢ Center the spacer and backer panel on the overlay ant | ag" is not always equal to
.
acker
"a 4
top-to-bottom offset.
panel and secure with glue and screws. Screws must Panel ' & ~ Spacer
be countersunk into the backer panel.
250° + .10" + .750" = 1.100" Total Panel Thickness
IMPORTANT NOTE - Dispenser Models
The refrigerator is supplied with two dispenser trims, * The overlay panel must be constructed according to
one for framed panels and one for overlay panels. the specifications shown to achieve the correct total
The overlay dispenser trim is designed to fit a total thickness.
panel thickness of 1.100". ¢ Alternative panel construction methods such as
¢ If the panel is less than 1.100" a noticeable gap may securing a 3/4" panel to a 1/4" backer panel cannot
be created around the dispenser trim. be used. Another method, routing a 3/4" thick
¢ If the panel is more than 1.100" the dispenser trim panel on all sides cannot be used. These methods
cannot be secured to the door. will not result in the required 1.100" panel thickness.
See Dispenser Trim Fit Example, page 9. middle rail is required. See page 9 for details.
When a raised panel design is to be used, a custom
a
Grille Panel
Dispenser
Cutout
Freezer Fresh Food
Panel Panel
kK—p |b -¢-_]
Dispenser Cutout *Cut the dispenser opening after the backer, spacer and overlay
Tor : panels have been assembled.
IMPORTANT NOTE: Maximum total weight for the assembled
panels:
® Fresh food door panel — 75 lbs.
© Freezer door panel — 53 lbs.
* Grille Panel — 18 lbs.
36" Side-by-Side (in inches}
1/4" Backer Panel —-33-7/8 68-3/8 14-9/16 18-9/16
10" Spacer Panel 33 8-3/8 67 13-1/4 17-1/4
3/4" Overlay Panel 34-1/8 9-1/4 ~—-68-5/8 14-13/16 — 18-13/16
42" Side-by-Side (in inches)
1/4" Backer Panel —-39-7/8 14-9/16 —-24-9/16
10" Spacer Panel 39 8-5/8 67 13-1/4 23-1/4
3/4" Overlay Panel = 40-1/8 »=—-9-3/4_—«68-5/8 14-13/16 24-13/16
48" Side-by-Side (in inches}
A B oi D a
1/4" Backer Panel 45-7/8 + 9-1/2 —-68-3/8 18-9/16 26-9/16
10" Spacer Panel 45 8-5/8 67 17-1/4 25-1/4
3/4" Overlay Panel = 46-1/8 »=—-9-3/4_—«68-5/8 18-13/16 26-13/16