1. Manuals
  2. Brands
  3. HP Manuals
  4. Server
  5. 9000 rp3410
  6. User's & service manual

HP 9000 rp3410 User's & Service Manual

Hide thumbs Also See for 9000 rp3410:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , Installation Manual
User Service Guide
HP 9000 rp3410 and HP 9000 rp3440
Manufacturing Part Number: A7137-96008
Fourth Edition
April 2007
© Copyright 2007 Hewlett-Packard Development Company, L.P.

Advertisement

Table of Contents
loading

Related Manuals for HP 9000 rp3410

Summary of Contents for HP 9000 rp3410

  • Page 1 User Service Guide HP 9000 rp3410 and HP 9000 rp3440 Manufacturing Part Number: A7137-96008 Fourth Edition April 2007 © Copyright 2007 Hewlett-Packard Development Company, L.P.

  • Page 2: Legal Notices

    Copyright Notices. © Copyright 2007 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.

  • Page 3: Table Of Contents

    HP 9000 rp3410 and rp3440 Server Views........
  • Page 4 Installing the Server Into a Rack, Non-HP Rack, or Pedestal .......
  • Page 5 Standard HP-UX Booting Using Boot Console Handler........
  • Page 6 Contents Cleaning Procedures ..............145 6.
  • Page 7 Contents Removing a Removable Media Drive ..........208 Replacing a Removable Media Drive .
  • Page 8 Contents...
  • Page 9 Table 3-1. HP 9000 rp3410 and rp3440 Server Features....... . .
  • Page 10 Tables Table 5-6. System Board LEDs ........... . . 145 Table 5-7.
  • Page 11 Figure 1-1. HP 9000 rp3410 and rp3440 Servers - Front View ......
  • Page 12 Figures Figure 3-28. Remove the Front Portion of the Processor Airflow Guide ..... 82 Figure 3-29. Routing the Turbofan Power Cables through Heatsink Posts....83 Figure 3-30.
  • Page 13 Figures Figure 6-17. Fan 2 Removal ............162 Figure 6-18.
  • Page 14 Figures Figure 6-60. Removable Media Drive Removal and Replacement ......208 Figure 6-61. Removing the iLO MP card ..........210 Figure 6-62.

  • Page 15: About This Document

    About This Document This document provides information and instructions on how to service and troubleshoot the HP 9000 rp3410 and rp3440 servers. The document printing date and part number indicate the document’s current edition. The printing date changes when a new edition is printed. Minor changes may be made at reprint without changing the printing date.

  • Page 16: Typographic Conventions

    NOTE A note highlights useful information such as restrictions, recommendations, or important details about HP product features. Tips provide you with helpful hints for completing a task. A tip is not used to give essential information, but can be used, for example, to provide an alternate method for completing the task that precedes it.

  • Page 17: Table 2. Hp-Ux 11I Releases

    Separates items in a list of choices. HP-UX Release Name and Release Identifier Each HP-UX 11i release has an associated release name and release identifier. The uname (1) command with the -r option returns the release identifier. Table 2 shows the releases available for HP-UX 11i.

  • Page 18: Hp Encourages Your Comments

    • HP-UX Virtual Partitions http://www.hp.com/hpbooks/prentice/ptr_0130352128.html HP Books are available worldwide through bookstores, online booksellers, and office and computer stores. HP Encourages Your Comments HP encourages your comments concerning this document. We are truly committed to providing documentation that meets your needs.

  • Page 19: Overview

    Overview The HP 9000 rp3410 server is a 1P/1C, 1P/2C, rack- or pedestal-mount server. Similarly, the HP 9000 rp3440 server is a 1P/1C, 1P/2C, or 2P/2C, rack- or pedestal-mount server. Both of these servers are based on the PA-RISC processor family architecture.

  • Page 20: Hp 9000 Rp3410 And Rp3440 Server Views

    HP 9000 rp3410 and rp3440 Server Views HP 9000 rp3410 and rp3440 Server Views Figure 1-2, Figure 1-2, Figure 1-3, and Figure 1-4 show the front, rear, and pedestal views of the HP 9000 rp3410 and rp3440 servers. Figure 1-1...

  • Page 21: Figure 1-3 Hp 9000 Rp3410 And Rp3440 Servers - Rear View

    Overview HP 9000 rp3410 and rp3440 Server Views Figure 1-3 HP 9000 rp3410 and rp3440 Servers - Rear View Figure 1-4 HP 9000 rp3410 and rp3440 Servers - Pedestal Mount Chapter 1...

  • Page 22: Detailed Server Description

    Minimum memory size is as follows: — 512 MB (2 x 256 MB DIMMs in a HP 9000 rp3410, model A7136A server). — 1 GB (4 x 256 MB DIMMs in a HP9000 rp3410 model A7136B server, or in a HP 9000 rp3440 server). •...

  • Page 23: Pci Riser

    • Open page memory latency is 80 nanoseconds. PCI Riser Two (HP 9000 rp3410 server) or four (HP 9000 rp3440 server) independent PCI-X 133 MHz 64-bit 3.3V 15W slots. No 5V card and hot-pluggable support. Internal Core I/O The following is supported on the HP 9000 rp3410 and rp3440 servers: •...

  • Page 24: Enhanced Server Manageability Using The Integrity Ilo Mp

    The A9890A and A9891A RAID cards are supported to provide RAID for the embedded drives. • The A9827A cabling kit is required for internal RAID. See the HP 9000 rp3410 and HP 9000 rp3440 Upgrade Guide for complete RAID installation instructions.

  • Page 25: Dimensions And Values

    Overview Detailed Server Description Dimensions and Values Table 1-1 lists the dimensions and their values of the HP 9000 rp3410 and rp3440 servers. Table 1-1 Server Dimensions and Values Dimension Values Rack dimensions (depth x width x height) 26.8 in (67.9 cm) max. x 19.0 in (48.3 cm) x 3.4 in (8.6 cm) Pedestal dimensions (depth x width x height) 26.6 in (67.5 cm) x 11.6 in (29.5 cm) x 19.5 in (49.4 cm)

  • Page 26: Figure 1-5 System Block Diagram

    The following describes the main components of the system board: • Dual PA-RISC processors: — One or two processors enabled in HP 9000 rp3410 server — One, two, or four processors enabled in HP 9000 rp3440 server • ZX1 I/O and memory controller •...
  • Page 27 (ECC), and the hardware implementation supports the chip-spare feature. The minimum amount of memory that you can install is 512 MB (2x256 MB modules in a HP 9000 rp3410 model A7136A server), and 1 GB (4x256 MB modules in other HP 9000 rp34x0 servers). The maximum amount of memory that you can install is limited to 24 GB (12 x 2 GB modules) or 32 GB (8 x 4 GB modules) in a HP 9000 rp3440 server.

  • Page 28: Figure 1-6 Memory Block Diagram

    Overview Detailed Server Description Figure 1-6 shows the memory block diagram. Figure 1-6 Memory Block Diagram Memory Controller Memory Architecture The I/O ASIC memory interface supports two DDR cells, each of which is 144 data bits wide. The memory subsystem physical design uses a comb-filter termination scheme for both the data and address/control buses. This part of the topology is similar to other DDR designs in the computer industry.

  • Page 29: Table 1-2. Memory Array Capacities

    “3rd” and “4th.” Maximum memory capability of the HP 9000 rp3440 server is 24 GB or 32 GB. If 4 GB DIMMs are used, install eight DIMMs in the first eight slots. The remaining slots (9-12) must remain empty when 4 GB DIMMs are used.
  • Page 30 Overview Detailed Server Description • Supports 3.3V or universal-keyed PCI cards. 5V-keyed PCI cards are not supported. Processor Dependent Hardware (PDH) Controller The Processor Dependent Hardware (PDH) controller provides the following features. • 16-bit PDH bus with reserved address space for the following: —...
  • Page 31 10/100/1000 MB capable. USB Connectors The USB connectors provide: • High speed 480 MB/sec. capable. • Full speed 12 MB/sec. and low speed 1.5 MB/sec. • Support for USB keyboard and mouse. • HP-UX supports HP USB keyboard and mouse. Chapter 1...

  • Page 32: Table 1-3. Internal Disk And Dvd Paths

    Overview Detailed Server Description Disk and I/O Path Logging Some failures result in I/O path logging. These paths help to indicate the source of the error and can be included in the error message or logged into console or event logs. Table 1-3 describes the disk drive and DVD paths for the server.

  • Page 33: Table 1-5 Pci I/O Paths

    Bottom connector of 0/6/1/0 PCI card cage Table 1-6 describes the PCI I/O hardware paths for the server Table 1-6 PCI I/O Hardware Paths PCI Card Functionality MAPPER Path HP-UX Path USB Port 0/0/1/0 0/0/1/0 USB Port 0/0/1/0 0/0/1/0 Chapter 1...

  • Page 34: Table 1-6. Pci I/O Hardware Paths

    Overview Detailed Server Description Table 1-6 PCI I/O Hardware Paths (Continued) PCI Card Functionality MAPPER Path HP-UX Path USB Port 0/0/1/1 0/0/1/1 USB Port 0/0/1/1 0/0/1/1 IDE Controller 0/0/2/0 0/0/2/0 DVD Drive 0/0/2/0.0.0 0/0/2/0.0.0 Internal SCSI - Slot 0 0/1/1/0.0.0 0/1/1/0.0.0...

  • Page 35: Controls, Ports, And Leds

    Controls, Ports, and LEDs Controls, Ports, and LEDs This section describes the controls, ports, and indicators found on the front and rear panel locations of the HP 9000 rp3410 or rp3440 server. The servers are designed to be rack- or pedestal-mounted.
  • Page 36 Overview Controls, Ports, and LEDs Table 1-7 provides control panel and LED information. Table 1-7 Control Panel LEDs and Switches Name Function Power on/off The green on/off LED is illuminated when the power is on. Power Button Controls the power supply (turns system power on or off) if power is available to the power supply.

  • Page 37: Additional Controls And Indicators

    Reading and scanning hard drive Optional Removable Media Drive HP 9000 rp3410 and rp3440 servers are delivered without a removable media drive. You can add either a DVD or CD-RW/DVD drive. Each of these optional devices has one activity LED.

  • Page 38: Rear Panel

    Drive is active Rear Panel The rear panel of the HP 9000 rp3410 and rp3440 servers includes communication ports, I/O ports, ac power connector, and the locator LED/button. Additional LEDs located on the rear panel of the HP 9000 rp3410 and rp3440 servers signal the operational status of: •...

  • Page 39: Table 1-10. Rear Panel Connectors And Switches

    Overview Controls, Ports, and LEDs Table 1-10 lists the rear-panel connectors and switches. Table 1-10 Rear Panel Connectors and Switches Connector or Function Switch ac power Primary power connection for the server. LVD/SE SCSI 68-pin, low-voltage differential, single-ended U160 SCSI. This connector provides external SCSI connection on SCSI Channel B.

  • Page 40: Table 1-11 10/100/1000 Base-T Ethernet Lan Connector Leds

    Overview Controls, Ports, and LEDs Table 1-11 lists the 10/100/1000 base-T Ethernet LAN connector LED descriptions. Table 1-11 10/100/1000 Base-T Ethernet LAN Connector LEDs Description 1000BT Blinking green—the 1000 MHz with Ethernet protocol and twisted-pair wiring is enabled, off—no link. 100BT Blinking green—the 100 MHz with Ethernet protocol and twisted-pair wiring is enabled, off—no link.

  • Page 41: Table 1-13 Usb Pinouts

    Overview Controls, Ports, and LEDs Figure 1-14 shows the single USB port. Figure 1-14 Single USB Port 1 2 3 4 Table 1-13 lists the USB pinouts. Table 1-13 USB Pinouts Pin Number Signal Description +5 VDC Ground SCSI Port, Ultra 3, 68-Pin A single, Ultra 3, 68 pin SCSI connector is located at the rear panel of the server.

  • Page 42: Table 1-14. Scsi Port Pinouts

    Overview Controls, Ports, and LEDs Table 1-14 SCSI Port Pinouts (Continued) Pin Number Signal Description Pin Number Signal Description S3 (+DB 14) S37 (–DB 14) S4 (+DB 15) S38 (–DB 15) S5 (+DB P1) S39 (–DB P1) S6 (+DB 0) S40 (–DB 0) S7 (+DB 1) S41 (–DB 1)

  • Page 43: Table 1-15. Ilo Mp Card Lan Leds

    Overview Controls, Ports, and LEDs Table 1-14 SCSI Port Pinouts (Continued) Pin Number Signal Description Pin Number Signal Description S32 (+DB 9) S66 (–DB 9) S33 (+DB 10) S67 (–DB 10) S34 (+DB 11) S68 (–DB 11) iLO MP Card LAN LEDs The iLO MP card LAN uses an RJ-45 type connector.

  • Page 44: Powering The Server On And Off

    Overview Powering the Server On and Off Table 1-16 lists the iLO MP card LAN connector pinouts. Table 1-16 iLO MP Card LAN Connector Pinouts Pin Number Signal Description Not used Not used Not used Not used Powering the Server On and Off This section provides information on how to power off and power on the server.

  • Page 45: Powering On The Server

    Overview Powering the Server On and Off If the power restore feature is set to Always On through the iLO MP PR command, the server NOTE automatically powers on to the full power state. Powering On the Server Power on the server to full power using the following methods if the server is in the standby power state: •...
  • Page 46 Overview Powering the Server On and Off Step 1. Gracefully shut down the operating system. Step 2. Initiate a console session, and access the MP Main Menu Step 3. Enter CM to enable command mode. Step 4. Enter PC to use the remote power control command. Step 5.

  • Page 47: System Specifications

    “Environmental Specifications” on page 51 • “Physical and Environmental Specifications” on page 54 System Configuration Table 2-1 lists the minimum and maximum configuration options for the HP 9000 rp3410 and rp3440 servers. Table 2-1 Minimum and Maximum System Configurations Component...

  • Page 48: Dimensions And Values

    (N+1) capability. redundant (N+1) capability. Dimensions and Values Table 2-2 lists dimensions and their values of the HP 9000 rp3410 and rp3440 servers. Table 2-2 Server Dimensions and Values Dimension Values Rack dimensions (depth x width x height) 26.8 in (67.9 cm) max.

  • Page 49: Grounding

    Electrical Specifications This section provides electrical specifications for the server. AC Power Cords Table 2-3 lists the power cables available for use with the HP 9000 rp3410 and rp3440 servers. Table 2-3 Power Cords Part Number...

  • Page 50: Circuit Breaker

    1. Disconnect the power cord. 2. Determine what caused the overload by contacting a HP support representative. 3. Reconnect the power cord, then reboot the system. If an overload occurs twice, there is an undetected short circuit somewhere.

  • Page 51: Power And Cooling

    System Specifications Environmental Specifications Power and Cooling Typical power consumption for a server is 600W/2050 Btu/h. The power consumptions listed in Table 2-5 are valid for a standard configuration as shipped (one 1 GHz processor, 6 GB of memory, 650W power supply, three hard disk drives, one graphics card, one LVD SCSI card).

  • Page 52: Operating Environment

    System Specifications Environmental Specifications Table 2-6 Environmental Specifications (Continued) Parameter Value LwA = 6.2 BA Maximum configuration (disk active) Rack system LwA = 6.4 BA Typical configuration (disk idle) LwA = 6.4 BA Maximum configuration (disk idle) LwA = 7.2 BA Maximum configuration (disk active) Operating altitude 3048m (10,000 ft.) max...

  • Page 53: Acoustic Noise Specification

    For maximum cooling effects, ensure that the chassis ventilation holes are not blocked or covered after installation. Acoustic Noise Specification The acoustic noise specification for the HP 9000 rp3410 or rp3440 servers is as follows: • 53 db LpA (sound pressure level at bystander position in a dedicated computer room environment temperature of <25°C)

  • Page 54: Physical And Environmental Specifications

    Physical and Environmental Specifications Table 2-7 provides temperature and airflow information for minimum, typical, and maximum configurations for the HP 9000 rp3410 and rp3440 servers. It also lists the server and rack weights and dimensions. Table 2-7 Physical and Environmental Specifications...

  • Page 55: Installing The System

    “Troubleshooting” on page 123 Introduction The HP 9000 rp3410 server is a 1P/1C, 1P/2C, rack- or pedestal-mount server. Similarly, the HP 9000 rp3440 server is a 1P/1C, 1P/2C, or 2P/2C, rack- or pedestal-mount server. Both of these servers are based on the PA-RISC processor family architecture.

  • Page 56: Server Views

    Installing the System Introduction Server Views Figure 3-1, Figure 3-2, Figure 3-3, and Figure 3-4 show the front, rear, and pedestal-mount views of the HP 9000 rp3410 and rp3440 servers. Figure 3-1 HP 9000 rp3410/rp3440 Server (Front View) Figure 3-2...

  • Page 57: Figure 3-4 Hp 9000 Rp3410/Rp3440 Server (Pedestal Mount)

    Installing the System Introduction Figure 3-4 HP 9000 rp3410/rp3440 Server (Pedestal Mount) Chapter 3...

  • Page 58: Detailed Server Description

    Installing the System Introduction Detailed Server Description The following sections list the main subsystems within the HP 9000 rp3410 and rp3440 servers. Features Table 3-1 lists the features of the HP 9000 rp3410 and rp3440 servers. Table 3-1 HP 9000 rp3410 and rp3440 Server Features...

  • Page 59: Safety Information

    Integrity iLO MP interprets and stores event IDs. Reviewing these events helps you diagnose and troubleshoot problems with the server. Dimensions and Values Table 3-2 lists the dimensions and their values of the HP 9000 rp3410 and rp3440 servers. Table 3-2 Server Dimensions and Values...

  • Page 60: Installation Sequence And Checklist

    • If installing an internal assembly, wear an antistatic wrist strap and use a grounding mat, such as those included in the Electrically Conductive Field Service Grounding Kit (HP 9300-1609). • Handle accessory boards and components by the edges only. Do not touch any metal-edge connectors or any electrical components on accessory boards.

  • Page 61: Unpacking And Inspecting The Server

    IMPORTANT Inspect each carton for shipping damage as you unpack the server. Checking the Inventory The sales order packing slip lists all of the equipment shipped from HP. Use this packing slip to verify that all of the equipment has arrived.

  • Page 62: Returning Damaged Equipment

    To identify each item by part number, see the sales order packing slip. NOTE Returning Damaged Equipment If the equipment is damaged, contact your HP customer service representative immediately. The service representative initiates appropriate action through the transport carrier or the factory and assists you in returning the equipment.

  • Page 63: Installing Additional Components

    Accessing a Rack-Mounted Server HP 9000 rp3410 and rp3440 servers are designed to be rack mounted. The following procedure explains how to gain access to a server that is mounted in an approved rack. For slide installation instructions, see the Installation Guide, Mid-Weight Slide Kit (HP part number 5065-7291).

  • Page 64: Figure 3-5 Release The Rack Latches

    Installing the System Installing Additional Components Figure 3-5 Release the Rack Latches Step 3. Slide the server out of the rack until the guide-rail release clips are visible. Insert the Server into the Rack To insert the server into the rack, follow these steps: Step 1.

  • Page 65: Figure 3-6 Removing And Replacing The Top Cover On A Rack-Mounted Server

    Installing the System Installing Additional Components Figure 3-6 Removing and Replacing the Top Cover on a Rack-Mounted Server Step 3. Lift the cover off the server chassis. Replacing the Top Cover on a Rack-Mounted Server CAUTION Secure any wires or cables in the server so they will not get cut or interfere with the replacement of the cover.

  • Page 66: Figure 3-8 Closing The Top Cover

    Installing the System Installing Additional Components Step 2. Grasp the blue release lever and slide the cover toward the front of the server until the lever snaps into place. Figure 3-8 Closing the Top Cover Step 3. Slide the server into the rack enclosure and reconnect the power and external cables. Removing and Replacing the Front Bezel on a Rack-Mounted Server You must remove the front bezel from the chassis to gain access to the power supplies and optical drive.

  • Page 67: Figure 3-10 Replacing The Front Bezel

    Installing the System Installing Additional Components Step 2. Rotate the front panel outward and lift it off the server chassis. Replacing the Front Bezel on a Rack-Mounted Server Step 1. Insert the bezel latches into the matching slots on the server chassis. Step 2.

  • Page 68: Figure 3-11 Removing The Side Cover On A Pedestal-Mounted Server

    Installing the System Installing Additional Components Figure 3-11 Removing the Side Cover on a Pedestal-Mounted Server Removing the Top Cover on Pedestal-Mounted Server To remove the top cover, follow these steps: Step 1. Turn the top cover lock keyswitch to the unlocked position. Step 2.

  • Page 69: Figure 3-12 Removing The Top Cover On A Pedestal-Mounted Server

    Installing the System Installing Additional Components Figure 3-12 Removing the Top Cover on a Pedestal-Mounted Server Step 4. Remove the top cover. CAUTION The server depends on the access panels being closed for proper cooling of internal components. Operating the server with the cover removed can cause the server to quickly overheat.

  • Page 70: Figure 3-13 Top Cover Alignment Mark

    Installing the System Installing Additional Components Figure 3-13 Top Cover Alignment Mark To replace cover, align front edge here then slide forward Step 2. Place the top cover on the chassis and slide it toward the front of the server until the blue release lever snaps in place.

  • Page 71: Figure 3-15 Replacing The Side Cover On A Pedestal-Mounted Server

    Installing the System Installing Additional Components Figure 3-15 Replacing the Side Cover on a Pedestal-Mounted Server Step 2. Close the cover until it snaps onto the server chassis. Removing and Replacing Front Bezel on a Pedestal-Mounted Server You must remove the front bezel from the chassis to gain access to the power supplies and optical drive. Removing the Front Bezel on a Pedestal-Mounted Server To remove the front bezel parts, follow these steps: Step 1.

  • Page 72: Figure 3-16 Removing The Front Bezel On A Pedestal-Mounted Server

    Installing the System Installing Additional Components Figure 3-16 Removing the Front Bezel on a Pedestal-Mounted Server Step 2. Lift the bezel off the mounting tabs and away from the chassis. Replacing the Front Bezel on a Pedestal-Mounted Server To replace the front bezel parts, follow these steps: Step 1.

  • Page 73: Installing Internal Hard Disk Drives

    Installing the System Installing Additional Components Figure 3-17 Aligning the Pedestal Front Bezel Step 2. Rotate the bezel against the chassis so that it snaps into place. Installing Internal Hard Disk Drives This section provides information about installing additional internal hard disk drives. CAUTION A hot-pluggable device can require interaction with the operating server before the device can be safely installed into the server.

  • Page 74: Figure 3-18. Front View Of The Hp 9000 Rp3410/Rp3440 Server

    Two additional hard disk drives can be added to the server in slots 2 and 3. Always use low profile disk drives (1 inch height) in HP 9000 rp3410 and rp3440 servers. To install a hard disk drive, follow these steps: Step 1.

  • Page 75: Figure 3-19. Filler Removal From Slot 1

    Installing the System Installing Additional Components Figure 3-19 Filler Removal from Slot 1 Step 3. Slide the hard disk drive into the slot until it is seated. Figure 3-20 Disk Drive Installation in Slot 3 Step 4. Close the drive ejector handle by pushing it down until it clicks. Step 5.

  • Page 76: Figure 3-21 Hard Drive Lock

    Installing the System Installing Additional Components a. Press the hard drive locking lever down into the locked position. b. Replace the cover and bezel. (See “Removing and Replacing Server Covers and Bezels” on page 63.) Figure 3-21 Hard Drive Lock Step 6.

  • Page 77: Installing A Dvd Drive

    Failure to properly complete the steps in this procedure will result in erratic server behavior or system failure. For assistance with this procedure contact your local HP Authorized Service Provider. Figure 3-22...

  • Page 78: Removing And Replacing Airflow Guides

    Installing the System Installing Additional Components Installing the DVD Drive To install a DVD drive, follow these steps: Step 1. Power off the server and disconnect power and external cables. Step 2. Remove the front bezel and cover. (See “Removing and Replacing Server Covers and Bezels” on page 63.) Step 3.

  • Page 79: Figure 3-23 Airflow Guides Locations

    Installing the System Installing Additional Components Figure 3-23 Airflow Guides Locations Processor Airflow Guide Memory Airflow Guide Front Portion of Processor Airflow Guide Removing and Replacing the Memory Airflow Guide Removing the Memory Airflow Guide Step 1. Power off the server and disconnect power and external cables. Step 2.

  • Page 80: Figure 3-25 Removing The Processor Airflow Guide

    Installing the System Installing Additional Components Replacing the Memory Airflow Guide Step 1. Align the guides on both sides of the airflow guide with the slots on the chassis. Step 2. Insert the memory airflow guide in the slots. Step 3. Replace the cover. (See “Removing and Replacing the Top Cover on a Rack-Mounted Server” on page 64.) Removing and Replacing the Processor Airflow Guide Removing the Processor Airflow Guide...

  • Page 81: Figure 3-26 Removing Fans 1A And 1B

    Installing the System Installing Additional Components Figure 3-26 Removing Fans 1A and 1B Fan 1A Fan 1B Step 6. Grasp system fan 1B and lift it from its socket (Figure 3-26). Step 7. Remove the memory airflow guide. “Removing the Memory Airflow Guide” on page 79 Step 8.

  • Page 82: Figure 3-27 Open The Release Clip

    Installing the System Installing Additional Components Figure 3-27 Open the Release Clip Step 9. Disconnect the power cable connected to the guide from the system board by squeezing the clips. Step 10. Lift the front portion of the processor airflow guide out of the server. Figure 3-28 Remove the Front Portion of the Processor Airflow Guide Chapter 3...

  • Page 83: Figure 3-29 Routing The Turbofan Power Cables Through Heatsink Posts

    Installing the System Installing Additional Components Replacing the Processor Airflow Guide Step 1. Replace the front portion of the airflow guide: a. Align the release latch of the front half of the airflow guide over the release latch post and snap it in place.

  • Page 84: Installing Additional System Memory

    2 GB) • 4 GB (HP 9000 rp3440 only). If 4 GB DIMMs are used, only one configuration (8 X 4 GB in the first eight sockets) is supported. Dissimilar DIMM sizes can be used across the entire system board (except when 4 GB DIMMs are used) but both DIMMs in a pair (first group of four, connectors 0A and 0B of HP 9000 rp3410) and all four DIMMs of any quad must be identical.

  • Page 85: Figure 3-30 Dimm Slot Identification

    Memory Configuration T The HP 9000 rp3410 server supports DDR SDRAM DIMMs with ECC and chip spare protection. This server has 12 DIMM slots and supports a maximum of six GB of total system memory. Memory usage in the server varies with the model designation.
  • Page 86 A7136B), memory must be installed as quads (groups of four). This allows memory configurations of four, eight, or twelve DIMMs. Thus, the HP 9000 rp3410 server must include a minimum of 512 MB (model A7136A) or 1 GB (model A7136B) and can include up to six GB of memory in combinations of 256 MB, 512 MB, and 1 GB DIMMs.
  • Page 87 System Firmware Requirements If you are using 4 GB DIMMs in a HP 9000 rp3440 server, system firmware must be greater than revision 44.24. Use the BCH FV command, or the iLO MP SR command to display the system firmware revision status.

  • Page 88: Removing And Replacing The Pci Card Cage

    Installing the System Installing Additional Components Figure 3-31 Inserting DIMM into Connector Step 6. Replace the memory airflow guide. (See “Replacing the Memory Airflow Guide” on page 80.) Step 7. Replace the server cover. (See “Removing and Replacing the Top Cover on a Rack-Mounted Server” on page 64.) Step 8.

  • Page 89: Figure 3-32 Removing The Pci Card Cage

    Installing the System Installing Additional Components Step 3. Lift up on the PCI card cage release lever and the back edge of the PCI card cage and lift the PCI card cage out of the server. Figure 3-32 Removing the PCI Card Cage Step 4.

  • Page 90: Installing Pci Cards

    Installing PCI Cards The server can contain up to 4 PCI cards. PCI cards are located in the PCI card cage. The HP 9000 rp3410 server provides two 64-bit, 133 MHz PCI-X card sockets as slots 1 and 2. The HP 9000 rp3440 server provides four 64-bit, 133 MHz PCI-X card sockets as slots 1 through 4.

  • Page 91: Figure 3-34 Installing A Pci Card

    Installing the System Installing Additional Components Failure to observe this warning can result in personal injury or damage to equipment. CAUTION Observe all ESD safety precautions before attempting this procedure. Failure to follow ESD safety precautions can result in damage to the server. Carefully read the following information concerning PCI slot configuration.

  • Page 92: Installing An Additional Power Supply

    Use diagnostics provided by the offline diagnostic environment to exercise the card added. Installing an Additional Power Supply The supported configuration of the HP 9000 rp3410 and rp3440 servers requires a minimum of one power supply to be installed. A second, optional hot-swappable power supply, can be installed to provide redundant (N+1) capability.

  • Page 93: Installing An Additional Processor Module

    The HP 9000 rp3410 server supports one processor socket. This socket will accept one dual processor module which contains two 800 MHz CPUs. The HP 9000 rp3410 server 1P/1C configuration includes two CPUs in a single module, but only one CPU is enabled. (The second CPU can be enabled as part of a server upgrade.) The HP 9000 rp3440 server supports two processor sockets.

  • Page 94: Figure 3-37 Unlocking The Dual Processor Module Locking Mechanism

    Provider. Observe all ESD safety precautions before attempting this procedure. Failure to follow ESD safety precautions can result in damage to the server. Processor tool kit (HP part number 5069-5441) is required for installation of a processor NOTE module. Processor modules are located on the system board. The system board can support either one or two dual processor modules.

  • Page 95: Figure 3-38 Aligning The Processor Module

    Installing the System Installing Additional Components Protective covers can be installed to protect connector pins. These covers can be NOTE saved for future use. Step 7. Use the four locator posts on the heatsink and the turbo fan power cable to properly align the fan and dual processor module on the system board.

  • Page 96: Figure 3-39 Locking The Dual Processor Module In Place

    Installing the System Installing Additional Components Figure 3-39 Locking the Dual Processor Module in Place CPU Install Tool (2.5 mm Driver or Allen Wrench) Step 9. Slide the sequencing retainer plate toward the front of the server. Figure 3-40 Slide the Sequencing Retainer Plate Step 10.

  • Page 97: Figure 3-41 Secure The Captive Screws

    Installing the System Installing Additional Components Figure 3-41 Secure the Captive Screws CPU Install Tool Step 11. Locate the two power pod module shims on the system board. (On servers delivered with only one dual processor module installed, the power module shims are held in place by screws with plastic spacers over the threads.) Remove the holding screws and discard the plastic spacers.

  • Page 98: Figure 3-43 Aligning The Processor Module Power Pod

    Installing the System Installing Additional Components Figure 3-43 Aligning the Processor Module Power Pod Step 13. Align the two mounting screw holes on the power pod module with the screw holes in the shims on the system board’s metal mounting bracket. Screw in the power pod module mounting screws. (Use the screws removed in step 11.) Chapter 3...

  • Page 99: Figure 3-44 Installing The Processor Module Power Pod Mounting Screws

    Installing the System Installing Additional Components Figure 3-44 Installing the Processor Module Power Pod Mounting Screws Step 14. Connect the power pod cable to the power connector on the system board. Chapter 3...

  • Page 100: Figure 3-45 Connecting The Power Pod Cable

    Installing the System Installing Additional Components Figure 3-45 Connecting the Power Pod Cable Chapter 3...

  • Page 101: Figure 3-46 Routing The Turbofan Power Cables Through Heatsink Posts

    Installing the System Installing Additional Components CAUTION Turbo fan power cables can be damaged if pinched between the heatsink posts and the processor airflow guide. Ensure that the cables are below the top surface of the heatsink posts before installing the processor airflow guide. Step 15.

  • Page 102: Replacing The System Battery

    The server has two batteries. The main system battery is located on the system board. The other battery is located on the underside of the iLO MP card. Battery Notice This product contains a Lithium battery (HP part number 1420-0386). Lithium batteries can explode if mistreated. Do not recharge, disassemble, or WARNING dispose of lithium batteries in a fire.

  • Page 103: Figure 3-47 Replacing The System Battery

    Installing the System Installing Additional Components Figure 3-47 Replacing the System Battery Step 7. Replace the cover. (See “Removing and Replacing Server Covers and Bezels” on page 63 for instructions.) Step 8. Reconnect power and external cables and turn on the server. Step 9.

  • Page 104: Installing The Server Into A Rack, Non-Hp Rack, Or Pedestal

    HP 9000 entry class servers that are installed into racks are shipped with equipment mounting slides. The Mid-Weight Slide Kit, (HP part number 5065-7291) is provided with each set of slides. Follow the steps in the kit installation guide to determine where and how to place the server into the rack.

  • Page 105: Connecting The Cables

    200 to 240 VAC at 13 amps. If two power supplies are installed, both power supplies must be connected separately to an ac power source. Core I/O Connections Each HP 9000 rp3410 and rp3440 server core I/O includes: • Four USB ports.

  • Page 106: Applying Standby Power To The Server

    Installing the System Connecting the Cables Applying Standby Power to the Server To apply standby power to the server, follow these steps: Step 1. If the server has one power supply installed in slot P1, plug the power cord into that receptacle. Plug the other end of the power cord into an appropriate outlet.

  • Page 107: Console Setup

    Installing the System Console Setup Console Setup This section describes how to set up and start a console session on the server and includes the following steps: • Determine the physical access method to connect cables. There are two physical connections to the iLO —...

  • Page 108: Setup Flowchart

    Installing the System Console Setup Setup Flowchart Use this flowchart as a guide to assist in the iLO MP setup process. Figure 3-49 iLO MP Setup Flowchart and IP address and IP address Chapter 3...

  • Page 109: Preparation

    Console Connection Matrix Operating Console Connection Required Connection Components System Method HP-UX 10/100 LAN cable LAN port 1. RS-232 DB-9F to DB-9F straight cable Local RS-232 serial port 2. Console device (for example, a laptop or ASCII terminal) Remote/modem port Determining the iLO MP LAN Configuration Method To access the iLO MP through the iLO MP LAN, the iLO MP must acquire an IP address.

  • Page 110: Configuring The Ilo Mp Lan Using Dhcp And Dns

    DHCP automatically configures all DHCP-enabled servers with IP addresses, subnet masks, and gateway addresses. All HP 9000 entry class servers with the iLO MP are shipped from the factory with DHCP enabled. HP recommends using the DHCP and DNS method to simplify access to the iLO MP.

  • Page 111: Table 3-7 Arp Ping Commands

    Installing the System Console Setup ARP Ping operational issues include the following: • You can use ARP Ping regardless of the status of DHCP, unless an IP address has ever been acquired using DHCP • When ARP Ping is successful, DHCP status is disabled •...

  • Page 112: Configuring The Ilo Mp Lan Using The Rs-232 Serial Port

    Installing the System Console Setup For example: arp -s 192.0.2.1 00-00-0c-07-ac-00 Step 6. At the DOS prompt, enter ping followed by the IP address to verify that the iLO MP LAN port is configured with the appropriate IP address. The destination address is the IP address that is mapped to the MP MAC address.
  • Page 113 Installing the System Console Setup IMPORTANT Do not use hpterm and vt100 terminal types at the same time. There are many different emulation software applications. Consult the help section of your emulation software application for instructions on how to configure the software options. Step 3.

  • Page 114: Logging In To The Ilo Mp

    = Oper User account and password are case sensitive. NOTE IMPORTANT For security reasons, HP strongly recommends that you modify the default settings during the initial login session. Make the following changes using any of the iLO MP user interfaces.
  • Page 115 Use directory services. Use the corporate directory to manage iLO MP user access. This is ideal for environments with a large number of frequently changing users. If you plan to use directory services, HP recommends leaving at least one local account enabled as an alternate method of access.

  • Page 116: Accessing The Host Console

    Installing the System Accessing the Host Console Accessing the Host Console This section describes the different ways to access the host console of the server. Accessing the Host Console With the TUI - CO Command This section describes the steps to access the host console using the text user interface (TUI). To access the host console through the iLO MP, follow these steps: Step 1.

  • Page 117: Accessing The Graphic Console Using Vga

    Installing the System Accessing the Host Console Step 3. Click . The page displays after login. Sign In Status Summary Figure 3-51 Status Summary Page Function Tabs Navigation Bar Display Screen Step 4. Select the Web interface functions by clicking the tabs at the top of the page.

  • Page 118: Powering The Server On And Off

    Installing the System Powering the Server ON and OFF IMPORTANT The server console output does not display on the console device screen until the server boots to the BCH . Start a console session using the RS-232 serial port method to view console Main Menu output before booting to the BCH or to access the iLO MP.

  • Page 119: Powering On The Server

    Installing the System Powering the Server ON and OFF If the power restore feature is set to Always On through the iLO MP PR command, the server NOTE automatically powers on to the full power state when the power cord is plugged in to the server. Powering On the Server Power on the server to full power using the following methods if the server is in the standby power state: •...

  • Page 120: Booting The Operating System

    This section covers procedures for booting and shutting down an operating system on the server. Supported Operating System The only supported operating system on the HP 9000 rp3410 and rp3440 servers is HP-UX 11i Version 1 (and higher HP-UX versions that support PA-RISC servers.) Booting and Shutting Down HP-UX This section describes booting and shutting down HP-UX on the HP 9000 rp3410 and rp3440 servers.
  • Page 121 (BCH). The BCH enables you to control the server’s booting environment. To set the boot path if HP-UX is at a path other than the primary path, follow these steps: To boot HP-UX, follow these steps: Step 1.

  • Page 122: Verifying The Server Configuration Using Boot Console Handler

    Booting the Operating System For details, see the shutdown (1M) manpage and follow these steps: Step 1. From the HP-UX command line, issue the shutdown command to shut down the HP-UX operating system. Step 2. Log in to HP-UX running on the server that you want to shut down.

  • Page 123: Troubleshooting

    Offline Diagnostics Environment (ODE) which runs from BCH. Descriptions and user information about offline troubleshooting tools are available on the Web at: http://www.docs.hp.com. The offline tools are available for downloading at: http://www.software.hp.com.

  • Page 124: Server Does Not Power On

    Installing the System Troubleshooting Table 3-10 describes what happens when the server is on with the operating system running, and you press the power button. Table 3-10 Server Power Button Functions When Server is On and OS is Running Action Reaction One to three seconds System power turns off (software controlled power off)

  • Page 125: Operating System Boots With Problems

    Installing the System Troubleshooting • Offline Diagnostic Environment (ODE) Operating System Boots with Problems If the operating system is running and you are experiencing problems, use the following tools to help solve the problem: • LEDs • Error Messages and event logs Intermittent Server Problems You can usually trace intermittent problems that occur during installation to power source problems, a loose connector, or some other hardware problem.

  • Page 126: Downloading And Installing The Latest Version Of The Firmware

    4. Exercise the appropriate self-test features of the console software. Downloading and Installing the Latest Version of the Firmware HP makes every effort to provide you with the most current version of firmware. However, there can be instances when this is not the case.

  • Page 127: Table 3-12. Front Control Panel Led Definitions

    Installing the System Troubleshooting Figure 3-52 Control Panel LEDs and Buttons Locator Button and LED Power Button Diagnostics LEDs System (Disabled) Power On/Off LED LAN System Table 3-12 Front Control Panel LED Definitions LED/ State Flash Rate Color Description Button System Running Steady...
  • Page 128 Installing the System Troubleshooting Chapter 3...

  • Page 129: Information To Collect Before You Contact Support

    Try to determine precisely what did or did not happen. Step 2. Collect the following information: • The model number of the server (for example, HP 9000 rp3440) • The product number of the server. This is found on the identification label, which is found at the front of the unit (typically A9956A, A9951A, and so on).
  • Page 130 Installing the System Troubleshooting Chapter 3...

  • Page 131: Booting The Operating System

    Booting the server loads the operating system, which is essential for running all other programs. You can only run one operating system on the server at one time. The HP-UX 11i version 1 (and higher HP-UX versions that support PA-RISC systems) is supported on the server.

  • Page 132: Booting And Shutting Down Hp-Ux

    (BCH). The BCH enables you to control the server’s booting environment. To set the boot path if HP-UX is at a path other than the primary path, follow these steps: To boot HP-UX, follow these steps: Step 1.

  • Page 133: Booting Hp-Ux In Single-User Mode

    -lm. ISL> Shutting Down HP-UX To shut down HP-UX running on a system, use the shutdown command. You have the following options when shutting down HP-UX: • To shut down and reboot an HP-UX system, use the shutdown -r command.

  • Page 134: Verifying The Server Configuration Using Boot Console Handler

    Booting the Operating System Verifying the Server Configuration Using Boot Console Handler Verifying the Server Configuration Using Boot Console Handler From the BCH , enter in to go the . Use the corresponding command from the Main Menu INformation Menu menu to verify the type and quantity of processors, memory, and I/O cards: Step 1.

  • Page 135: Troubleshooting

    Damage to system components can result due to improper cooling airflow. To troubleshoot the server with online diagnostic tools, you must be familiar with the HP-UX operating system. You should also be familiar with the Offline Diagnostics Environment (ODE) which runs from BCH.

  • Page 136: Troubleshooting System Power

    Troubleshooting Troubleshooting System Power Troubleshooting System Power This section provides information and procedures for troubleshooting the system power. Using the Front Panel Power Button The server power button on the front panel operates differently, depending on how long the button is held in and on what the system is doing when the button is pressed.

  • Page 137: Operating System Does Not Boot

    Offline Diagnostic Environment (ODE) • iLO MP Troubleshooting Using Online Support Tools The following online support tools are available from the HP-UX environment. Support Tools Manager Support Tools Manager (STM) is available in three user interfaces: • Graphical interface for X-based terminals (XSTM) •...

  • Page 138: Ilo Mp

    From the list of Main Menu selections, select: (E) Enable Monitoring iLO MP For complete information on the iLO MP see the HP Integrity and HP 9000 iLO MP Operations Guide on the Web. The following information provides iLO MP troubleshooting steps.
  • Page 139 Troubleshooting Troubleshooting Using Online Support Tools Log Name Entries % Full Latest Timestamped Entry ------------------------------------------------------------------- E - System Event 01 Nov 2004 17:15:03 Event Log Navigation Help: View next block (forward in time, e.g. from 3 to 4) View previous block (backward in time, e.g. from 3 to 2) <CR>...

  • Page 140: Troubleshooting Using Offline Support Tools

    Troubleshooting Troubleshooting Using Offline Support Tools Troubleshooting Using Offline Support Tools Use the ODE CD to troubleshoot your HP 9000 rp3410 or rp3440 server by accessing the offline diagnostic environment (ODE). Offline Diagnostic Environment (ODE) Use ODE to evaluate specific hardware components using a command line interface. To access ODE from your ODE CD, follow these steps: Step 1.

  • Page 141: Identifying And Diagnosing Hardware Problems

    Troubleshooting Identifying and Diagnosing Hardware Problems Identifying and Diagnosing Hardware Problems Should a hardware failure occur, the system LED and the SEL will help you identify the problem: • LEDs. The lights on the front bezel of the server change color and blink in different patterns to help identify specific hardware problems.

  • Page 142: Lan Leds

    Troubleshooting Troubleshooting Using LEDs Table 5-3 System LED States (Continued) System LED State Blinking green Booting or running BCH. Blinking yellow (1/sec.) Attention: Alerts of levels 3-5 detected in the iLO MP logs The LED will turn off once the event log has been read. Blinking red (2/sec.) Fault: System Alert 7 detected, LED will blink until the problem is resolved...

  • Page 143: Table 5-5. Ilo Mp Card Lan Leds

    Troubleshooting Troubleshooting Using LEDs Four iLO MP card LAN LEDs are also on the rear panel: Table 5-5 lists the iLO MP card LAN LEDs. Table 5-5 iLO MP Card LAN LEDs LAN LED Location Color State Self-test Yellow iLO MP running selftest or error iLO MP has booted 10BT 2nd from top...

  • Page 144: System Board Leds

    Troubleshooting Troubleshooting Using LEDs System Board LEDs There are two additional LEDs that can help when troubleshooting the system. These LEDs are located on the system board close to the back of the system and are viewed through the small cooling holes in the system case.

  • Page 145: Cleaning Procedures

    BMC is active. Cleaning Procedures This section provides information on how to clean the HP 9000 rp3410 and rp3440 servers. IMPORTANT Power off the server when cleaning it. Table 5-7 provides instructions on how to clean the server.
  • Page 146 Troubleshooting Cleaning Procedures Chapter 5...

  • Page 147: Removing And Replacing Components

    Removing and Replacing Components This chapter describes how to remove and replace hardware in HP 9000 rp3410 and rp3440 servers. Use care to prevent injury and equipment damage when performing these procedures. Voltages can be present within the server. Many assemblies are sensitive to damage by electrostatic discharge.

  • Page 148: Required Service Tools

    • If installing an internal assembly, wear an antistatic wrist strap and use a grounding mat, such as those included in the Electrically Conductive Field Service Grounding Kit (HP 9300-1155). • Handle accessory boards and components by the edges only. Do not touch any metal-edge connectors or any electrical components on accessory boards.

  • Page 149: Location Of Internal Components And Connectors

    Removing and Replacing Components Location of Internal Components and Connectors Location of Internal Components and Connectors Figure 6-1 shows the internal physical layout of the server. Figure 6-1 Internal Physical Layout Pwr 2 Pwr 1 Fan 1A Fan 1B PS 2 PS 1 Fan 3 Fan 2...

  • Page 150: Table 6-2. Connector Locations

    Power supply fan connector PCI backplane connector SCSI connectors A & B Power module power connector Optical drive connector CPU power pods HP ZX1 memory and I/O iLO MP card connector controller (under heatsink) CPU 1 Memory sockets HP ZX1 I/O adapter...

  • Page 151: Removing And Replacing Server Covers And Bezel

    Accessing a Rack-Mount Server HP 9000 rp3410 and rp3440 servers are designed to be rack mounted. The following procedure explains how to gain access to a server that is mounted in an approved rack. For slide installation instructions, see the Installation Guide, Mid-Weight Slide Kit (HP part number 5065-7291).

  • Page 152: Figure 6-3 Release The Rack Latches

    Removing and Replacing Components Removing and Replacing Server Covers and Bezel Step 2. Release the rack latches by rotating them outward. Figure 6-3 Release the Rack Latches Step 3. Slide the server out of the rack until the guide-rail release clips are visible. Insert the Server into the Rack To insert the server into the rack, follow these steps: Step 1.

  • Page 153: Figure 6-4 Removing The Top Cover On A Rack-Mounted Server

    Removing and Replacing Components Removing and Replacing Server Covers and Bezel Step 2. Ensure the top cover lock keyswitch is in the unlocked position. Rotate the blue release lever toward the back of the server and slide the cover toward the back of the server. Figure 6-4 Removing the Top Cover on a Rack-Mounted Server Step 3.

  • Page 154: Figure 6-5 Aligning The Top Cover On A Rack-Mounted Server

    Removing and Replacing Components Removing and Replacing Server Covers and Bezel Step 1. Align the front edge of the top cover with the alignment mark on the optical drive bay. Figure 6-5 Aligning the Top Cover on a Rack-Mounted Server To replace cover, align front edge here then slide forward...

  • Page 155: Figure 6-7 Front Bezel Retaining Clip

    Removing and Replacing Components Removing and Replacing Server Covers and Bezel Removing and Replacing the Front Bezel on a Rack-Mounted Server You must remove the front bezel from the chassis to gain access to the power supplies and optical drive. Removing the Front Bezel Step 1.

  • Page 156: Accessing Pedestal-Mount Server

    Accessing Pedestal-Mount Server Both the HP 9000 rp3410 and the rp3440 servers are available in a pedestal configuration or can be converted from a rack to a pedestal configuration. To access the internal components on a pedestal server, you must remove the side and top covers.

  • Page 157: Figure 6-9. Removing The Side Cover On A Pedestal-Mounted Server

    Removing and Replacing Components Removing and Replacing Server Covers and Bezel b. Lift the side cover off of the server chassis. Figure 6-9 Removing the Side Cover on a Pedestal-Mounted Server Step 3. Remove the top cover. Figure 6-10 Removing the Top Cover on a Pedestal-Mounted Server a.

  • Page 158: Figure 6-11 Top Cover Alignment Mark

    Removing and Replacing Components Removing and Replacing Server Covers and Bezel c. Slide the top cover toward the back of the chassis and lift it off. CAUTION The server depends on the access panels being closed for proper cooling of internal components.

  • Page 159: Figure 6-12. Replacing The Top Cover On A Pedestal-Mounted Server

    Removing and Replacing Components Removing and Replacing Server Covers and Bezel b. Place the top cover on the chassis and slide it toward the front of the server until the blue release lever snaps in place. Figure 6-12 Replacing the Top Cover on a Pedestal-Mounted Server Step 5.

  • Page 160: Figure 6-14 Removing The Front Bezel On A Pedestal-Mounted Server

    Removing and Replacing Components Removing and Replacing Server Covers and Bezel Removing and Replacing the Front Bezel on a Pedestal-Mounted Server You must remove the front bezel from the chassis to gain access to the power supplies and optical drive. Removing the Front Bezel To remove the front bezel, follow these steps: Step 1.

  • Page 161: Removing And Replacing System Fans

    Removing and Replacing Components Removing and Replacing System Fans Replacing the Front Bezel on a Pedestal-Mounted Server To replace the front bezel, follow these steps: Step 1. Position the bezel at an approximate 45 degree angle and align the retaining slots at the bottom with the retaining tabs on the chassis.

  • Page 162: Figure 6-16 Fan 1A Or Fan 1B Removal

    Removing and Replacing Components Removing and Replacing System Fans a. To remove fan 1A, 1B, 2 or 3 from a rack-mounted server, or fan 3 from a pedestal server, grasp the appropriate fan and lift it out of the fan socket (Figure 6-16; Figure 6-17; Figure 6-18). Figure 6-16 Fan 1A or Fan 1B Removal Fan 1A Fan 1B...

  • Page 163: Replacing A System Fan

    Removing and Replacing Components Removing and Replacing the Power Supply Figure 6-18 Fan 3 Removal Fan 3 Replacing a System Fan Step 1. Grasp the replacement fan module and insert it into its fan socket. Step 2. For fans 1A, 1B, or 2, connect the fan power connector. Replace the top cover within five minutes to prevent damage to the server CAUTION components.

  • Page 164: Removing The Power Supply

    Removing and Replacing Components Removing and Replacing the Power Supply Removing the Power Supply To remove the power supply, follow these steps: Step 1. Remove the front bezel from the server. (See “Removing and Replacing Server Covers and Bezel” on page 151.) Step 2.

  • Page 165: Replacing The Power Supply

    Removing and Replacing Components Removing and Replacing the Power Supply Step 3. Press the power supply release lever down and slide the power supply out of the server. Figure 6-20 Removing the Power Supply Replacing the Power Supply To replace the power supply, follow these steps: Step 1.

  • Page 166: Removing And Replacing An Internal Hard Disk Drive

    Removing and Replacing an Internal Hard Disk Drive The HP 9000 rp3410 or rp3440 server can support up to three hot-pluggable, Low-Voltage Differential (LVD) hard disk drives. These hard disk drives are 3.5-inch form factor devices that connect to Ultra 160 Wide LVD SCSI interfaces on the disk cage backplane.

  • Page 167: Figure 6-22 Unlocking The Disk Drive

    Removing and Replacing Components Removing and Replacing an Internal Hard Disk Drive If you try to remove a hard disk drive without unlocking it from the server, you CAUTION will damage the hard drive bay. Figure 6-22 Unlocking the Disk Drive Step 3.

  • Page 168: Replacing A Hard Disk Drive

    Removing and Replacing Components Removing and Replacing an Internal Hard Disk Drive Step 4. Pull outward on the release lever to remove the drive from the server (Figure 6-23; Figure 6-24). Figure 6-24 Removing the Disk Drive Replacing a Hard Disk Drive To install or replace a hard disk drive, follow these steps: Step 1.

  • Page 169: Figure 6-25 Removing Disk Drive Slot Filler

    Removing and Replacing Components Removing and Replacing an Internal Hard Disk Drive Step 3. If a disk drive slot filler is installed, remove the slot filler by pulling it from the disk drive slot. Figure 6-25 Removing Disk Drive Slot Filler Step 4.

  • Page 170: Removing And Replacing Airflow Guides

    Step 7. Verify the drive replacement and operation by using the system utilities. (See the Utilities chapter or the HP Integrity and HP 9000 iLO MP Operations Guide for additional information.) • Use the iLO MP commands to verify operation.

  • Page 171: Removing And Replacing The Memory Airflow Guide

    Removing and Replacing Components Removing and Replacing Airflow Guides You must remove the processor airflow guide: • If it is damaged to the point that airflow across the dual processor modules is restricted. • To access components under the airflow guide. •...

  • Page 172: Removing And Replacing The Processor Airflow Guide

    Removing and Replacing Components Removing and Replacing Airflow Guides Step 3. Grasp the memory airflow guide and lift it out of the server. Figure 6-28 Removing the Memory Airflow Guide Replacing the Memory Airflow Guide Step 1. Align the guides on both sides of the airflow guide with the slots on the chassis. Step 2.

  • Page 173: Figure 6-29 Removing The Processor Airflow Guide

    Removing and Replacing Components Removing and Replacing Airflow Guides b. At the same time, grasp the back end of the airflow guide and lift the guide out of the server. Figure 6-29 Removing the Processor Airflow Guide Step 5. Remove the front portion of the airflow guide: a.

  • Page 174: Figure 6-30 Open The Release Clip

    Removing and Replacing Components Removing and Replacing Airflow Guides c. Rotate the clip clockwise to release the latch. Figure 6-30 Open the Release Clip d. Disconnect the power cable connected to the guide from the system board by squeezing the clip. Chapter 6...

  • Page 175: Figure 6-31 Remove The Front Portion Of The Processor Airflow Guide

    Removing and Replacing Components Removing and Replacing Airflow Guides e. Lift the front portion of the processor airflow guide out of the server. Figure 6-31 Remove the Front Portion of the Processor Airflow Guide Replacing the Processor Airflow Guide Step 1. Replace the front portion of the airflow guide: a.

  • Page 176: Figure 6-32 Routing Power Cables Through Heatsink Posts

    Removing and Replacing Components Removing and Replacing Airflow Guides Turbo fan power cables can be damaged if pinched between the heatsink posts and CAUTION the processor airflow guide. Ensure that the cables are below the top surface of the heatsink posts before installing the processor airflow guide. Figure 6-32 Routing Power Cables through Heatsink Posts Step 4.

  • Page 177: Removing And Replacing System Memory

    256 MB • 512 MB • 1 GB • 2 GB • 4 GB (HP 9000 rp3440 only). If 4 GB DIMMs are used, only one configuration (8 X 4 GB in the first eight sockets) is supported. Chapter 6...

  • Page 178: Rp3410 Memory Configuration

    DIMMs. Thus, the HP 9000 rp3410 server must include a minimum of 512 MB (model A7136A) or 1 GB (model A7136B) and can include up to 6 GB of memory in combinations of 256 MB, 512 MB, and 1 GB DIMMs.

  • Page 179: Rp3440 Memory Configuration

    System Firmware Requirements If you are using 4 GB DIMMs in a HP 9000 rp3440 server, system firmware must be greater than revision 45.10. Use the BCH FV command, or the iLO MP SR command to display the system firmware revision status.

  • Page 180: Replacing Deallocated Memory Ranks

    Removing and Replacing Components Removing and Replacing System Memory Replacing Deallocated Memory Ranks This section provides the steps necessary to replace deallocated memory ranks. When replacing deallocated memory ranks on a server with system firmware version 45.11 or NOTE greater, you must perform the following procedure before replacing the deallocated memory. This procedures is necessary to ensure that the memory is properly reallocated upon server boot.

  • Page 181: Installing System Memory

    Module sizes can be mixed, as long as DIMMs in each quad match. For example: • On HP 9000 rp3410 servers, it is acceptable to load four 256 MB DIMMs in sockets 0A, 0B, 1A, and 1B and four 512 MB or 1 GB DIMMs in sockets 2A, 2B, 3A, and 3B •...

  • Page 182: Figure 6-34 Inserting Dimm Into Connector

    Step 8. Reconnect power and external cables and turn on the server. Step 9. Verify the memory replacement and operation by using the system utilities. (See the Utilities chapter or the HP Integrity and HP 9000 iLO MP Operations Guide for additional information.) •...

  • Page 183: Removing And Replacing A Dual Processor Module

    Observe all ESD safety precautions before attempting this procedure. Failure to follow ESD safety precautions can result in damage to the server. NOTE Processor tool kit (HP part number 5069-5441) is required for removal and installation of a dual processor module. Removing a Dual Processor Module To remove a dual processor module, follow these steps: Step 1.

  • Page 184: Figure 6-35 Disconnect Power Pod Cable

    Removing and Replacing Components Removing and Replacing a Dual Processor Module Step 5. Disconnect the power pod cable from the power connector on the system board Figure 6-35 Disconnect Power Pod Cable Step 6. Remove and retain the two power pod mounting screws. Figure 6-36 Remove Power Pod Mounting Screws Chapter 6...

  • Page 185: Figure 6-37 Disconnect Power Pod From Dual Processor Module

    Removing and Replacing Components Removing and Replacing a Dual Processor Module Step 7. Slide the power pod toward the rear of the system board so that the power pod connector disconnects from its connector on the dual processor module (Figure 6-37. Figure 6-37 Disconnect Power Pod from Dual Processor Module Chapter 6...

  • Page 186: Figure 6-38 Remove Power Pod

    Removing and Replacing Components Removing and Replacing a Dual Processor Module Step 8. Lift the power pod up and out of the chassis. Place the power pod into an antistatic container (Figure 6-38). Figure 6-38 Remove Power Pod Chapter 6...

  • Page 187: Figure 6-39 Disconnect The Turbo Fan Cable

    Removing and Replacing Components Removing and Replacing a Dual Processor Module Step 9. Disconnect the turbo fan power cable. Figure 6-39 Disconnect the Turbo Fan Cable Step 10. Release the four heatsink captive screws on the module heat sink. Figure 6-40 Release Heatsink Captive Screws CPU Install Tool Step 11.

  • Page 188: Figure 6-41 Unlocking The Dual Processor Module Locking Mechanism

    Removing and Replacing Components Removing and Replacing a Dual Processor Module Step 12. Unlock the dual processor module locking mechanism using the CPU install tool. Insert the tool into the hole that runs down through the edge of the turbo fan heatsink and rotate the special processor tool 180 degrees counterclockwise.

  • Page 189: Figure 6-42 Removing The Dual Processor Module

    Removing and Replacing Components Removing and Replacing a Dual Processor Module Step 13. Lift the dual processor module and the turbo fan assembly up and out of the chassis (Figure 6-42). If protective pin covers are available, install the cover on processor connectors to shield connector pins.

  • Page 190: Installing A Dual Processor Module

    Removing and Replacing Components Removing and Replacing a Dual Processor Module Figure 6-43 Dual Processor Module Removal and Replacement Power Pod # 2 Power Pod # 1 Dual Proc #1 (in Socket CPU0) Dual Proc #2 (in socket CPU1) Installing a Dual Processor Module Either one or two dual processor modules are located on the system board.

  • Page 191: Figure 6-44 Unlocking The Dual Processor Module Locking Mechanism

    Removing and Replacing Components Removing and Replacing a Dual Processor Module Step 4. Unlock the dual processor module locking mechanism using the CPU install tool. Insert the tool into the hole that runs down through the edge of the heatsink and rotate the special processor tool 180 degrees counterclockwise.

  • Page 192: Figure 6-45 Aligning The Dual Processor Module

    Removing and Replacing Components Removing and Replacing a Dual Processor Module Step 6. Use the four locator posts on the heatsink and the turbo fan power cable to properly align the fan and dual processor module on the system board (Figure 6-45). The four locator posts will fit in locator holes on the system board processor module mount.

  • Page 193: Figure 6-46 Locking The Dual Processor Module In Place

    Removing and Replacing Components Removing and Replacing a Dual Processor Module Step 7. Use the special processor tool to lock the dual processor module in place on the system board. To do this, insert the special processor tool into the hole that runs down the side of the heatsink and rotate it clockwise 180 degrees (Figure 6-46).

  • Page 194: Figure 6-48 Power Module Shims

    Removing and Replacing Components Removing and Replacing a Dual Processor Module Step 10. If you are installing a second dual processor module in a server which contained only one dual processor module, remove the spacers from the power module mounting: (Figure 6-48.) a.

  • Page 195: Figure 6-49 Aligning The Processor Module Power Pod

    Removing and Replacing Components Removing and Replacing a Dual Processor Module Step 11. Slide the power module on the system board metal mounting bracket so that the connector on the power module makes contact with its connector on the dual processor module. Figure 6-49 Aligning the Processor Module Power Pod Chapter 6...

  • Page 196: Figure 6-50 Installing The Processor Module Power Pod Mounting Screws

    Removing and Replacing Components Removing and Replacing a Dual Processor Module Step 12. Align the two mounting screw holes on the power module with the screw holes in the shims on the system board’s metal mounting bracket (Figure 6-49). Screw in the power module mounting screws (Figure 6-50).

  • Page 197: Figure 6-51 Routing The Turbofan Power Cables Through The Heatsink Posts

    Removing and Replacing Components Removing and Replacing a Dual Processor Module Step 13. Route the turbo fan power cables through the heatsink posts so the cables will not be pinched when the processor airflow guide is set in place (Figure 6-51). Figure 6-51 Routing the Turbofan Power Cables through the Heatsink Posts Step 14.

  • Page 198: Removing And Replacing The System Battery

    Removing and Replacing the System Battery Step 19. Verify processor replacement and operation by using the system utilities. (See the Utilities chapter or the HP Integrity and HP 9000 iLO MP Operations Guide for additional information.) • Use the iLO MP commands to verify operation.

  • Page 199: Replacing The System Battery

    Removing and Replacing Components Removing and Replacing the System Battery Only lift the battery high enough to clear the holder. Excessive stress on the battery CAUTION holder retaining clip can damage the clip. Figure 6-53 Removing the System Battery Replacing the System Battery Step 1.

  • Page 200: Removing And Replacing The Pci Card Cage

    Removing and Replacing the PCI Card Cage Step 6. Verify the battery replacement and operation by using the system utilities. (See the Utilities chapter or the HP Integrity and HP 9000 iLO MP Operations Guide for additional information.) • Use the iLO MP commands to verify operation.

  • Page 201: Figure 6-54 Removing The Pci Card Cage

    Removing and Replacing Components Removing and Replacing the PCI Card Cage Step 3. Lift up on the PCI card cage release lever and the back edge of the PCI card cage and lift the PCI card cage out of the server (Figure 6-54). Figure 6-54 Removing the PCI Card Cage Chapter 6...

  • Page 202: Replacing The Pci Card Cage

    The server can contain up to four PCI cards. PCI cards are located in the PCI card cage. The HP 9000 rp3410 provides two 64-bit, 133 MHz PCI-X card sockets and the HP 9000 rp3440 server provides four 64-bit, 133 MHz PCI-X card sockets.

  • Page 203: Removing A Pci Or Graphics Card

    Removing and Replacing Components Removing and Replacing PCI Cards Ensure that the server is powered off and all power sources have been disconnected WARNING from the server before removing or replacing a PCI card. Voltages are present at various locations within the server whenever an ac power source is connected.

  • Page 204: Replacing A Pci Or Graphics Card

    Removing and Replacing Components Removing and Replacing PCI Cards Step 5. Install a PCI slot cover to close the cavity left by the removal of the PCI card (Figure 6-56). This will maintain the proper airflow within the chassis. Figure 6-56 Installing a PCI Slot Cover Replacing a PCI or Graphics Card Step 1.

  • Page 205: Removing And Replacing The Pci Backplane

    Use the BCH commands to verify operation. Removing and Replacing the PCI Backplane The HP 9000 rp 3410 and rp3440 server system backplane is called the PCI backplane and provides four PCI card sockets. The removal process is the same for both.

  • Page 206: Replacing The Pci Backplane

    Removing and Replacing Components Removing and Replacing the PCI Backplane Step 4. Lift the backplane over the top of the standoffs and slide it out of the cage (Figure 6-58). Figure 6-58 Removing the PCI Backplane Replacing the PCI Backplane Step 1.

  • Page 207: Removing And Replacing A Removable Media Drive

    Step 4. Replace the PCI card cage. (See “Replacing the PCI Card Cage” on page 202.) Step 5. Verify the backplane replacement and operation by using the system utilities. (See the Utilities chapter or the HP Integrity and HP 9000 iLO MP Operations Guide for additional information.) •...

  • Page 208: Removing A Removable Media Drive

    Failure to properly complete the steps in this procedure will result in erratic server behavior or system failure. For assistance with this procedure contact your local HP Authorized Service Provider. Removing a Removable Media Drive To remove a removable media drive, follow these steps: Step 1.

  • Page 209: Removing And Replacing The Ilo Mp Card

    Step 5. Reconnect the power and external cables and turn on the server. Step 6. Verify the drive replacement and operation by using the system utilities. (See the Utilities chapter or the HP Integrity and HP 9000 iLO MP Operations Guide for additional information.) •...

  • Page 210: Replacing The Ilo Mp Card

    Removing and Replacing Components Removing and Replacing the iLO MP Card Step 4. Unscrew the two mounting screws that connect the iLO MP card to the internal chassis post and the two external mounting screws that are located on both sides of the 25-pin serial connector. Figure 6-61 Removing the iLO MP card Step 5.

  • Page 211: Removing And Replacing The Ilo Mp Card Battery

    Enter the network settings recorded during iLO MP card removal (if available). Step 7. Verify the card replacement and operation by using the system utilities. (See the Utilities chapter or the HP Integrity and HP 9000 iLO MP Operations Guide for additional information.) •...

  • Page 212: Replacing The Ilo Mp Card Battery

    Step 2. Replace the iLO MP card. (See “Replacing the iLO MP card” on page 210.) Step 3. Verify the battery replacement and operation by using the system utilities. (See the Utilities chapter or the HP Integrity and HP 9000 iLO MP Operations Guide for additional information.) •...

  • Page 213: Removing And Replacing The Led Status Panel

    Removing and Replacing Components Removing and Replacing the LED Status Panel Removing and Replacing the LED Status Panel The LED status panel card contains the server and diagnostic LEDs. Removing the LED Status Panel Step 1. Power off the server and disconnect all power and external cables. Step 2.

  • Page 214: Removing And Replacing The System Board

    Removing and Replacing Components Removing and Replacing the System Board Removing and Replacing the System Board Server information is stored on the system board. If you are installing a new system board, you must write serial number and model string information to the system board after installation. Removing the System Board Step 1.

  • Page 215: Figure 6-65 Remove Backplane System Board Mounting Screws

    Removing and Replacing Components Removing and Replacing the System Board Step 5. Unscrew the six backplane system board mounting screws that connect the system board to the rear of the server chassis. Figure 6-65 Remove Backplane System Board Mounting Screws Step 6.

  • Page 216: Figure 6-67 Remove The System Board

    Removing and Replacing Components Removing and Replacing the System Board b. Lift up the processor module side of the system board and slide it free of the PCI card cage bay. Figure 6-67 Remove the System Board Chapter 6...

  • Page 217: Replacing The System Board

    Removing and Replacing Components Removing and Replacing the System Board Replacing the System Board Step 1. Grasp the new system board by its edges and carefully align it in the server: a. Angle the board to enable the PCI connector to slide into the PCI card cage bay area. b.

  • Page 218: Figure 6-69 Slide System Board In Chassis

    Removing and Replacing Components Removing and Replacing the System Board Step 2. Slide the system board back toward the rear of the server to secure the system board on its standoffs. Figure 6-69 Slide System Board in Chassis Step 3. Screw in the system board mounting screw. Step 4.

  • Page 219: Figure 6-71 Replacing Mechanical Covers

    Removing and Replacing Components Removing and Replacing the System Board Step 6. Replace the mechanical covers over the VGA and DB9 ports. Figure 6-71 Replacing Mechanical Covers Step 7. Replace the power connectors in their slots on the back of the server and screw in the power connector mounting screws.
  • Page 220 If you performed an upgrade, the certificate shows a new key and model number to be used Step 12. Verify the system board replacement and operation by using the system utilities. (See the Utilities chapter or the HP Integrity and HP 9000 iLO MP Operations Guide for additional information.) Chapter 6...

  • Page 221: Replacing The Resident System Board With A Replacement System Board

    All A7136B, A9948A, and A9949A products within the documented serial number ranges were shipped from the factory with an incorrect system setting product number. A7137-69001, HP 9000 rp34x0, changing to your system settings. CAUTION If this procedure is not performed correctly, you will not be able to set your server up without the help of an HP Customer Engineer.

  • Page 222: Replacing A System Board

    Failure to properly complete the steps in this procedure will result in erratic server behavior or server failure. For assistance with this procedure contact your local HP Authorized Service Provider. Before replacing the resident system board with the replacement system board (A7136-69001), you must locate the pull-out tag that is on the chassis of your server.

  • Page 223: Removing And Replacing The Power Supply Interface Module

    Removing and Replacing Components Removing and Replacing the Power Supply Interface Module Step 6. When prompted, enter the product number located on the pull-out tag. Confirm by answering Y when asked. If you made a mistake entering the product number, you can answer N and re-enter the product number when asked.

  • Page 224: Figure 6-74 Power Cables And Holding Clips

    Removing and Replacing Components Removing and Replacing the Power Supply Interface Module Step 4. Lift the power cables out of their metal holding clips. Figure 6-74 Power Cables and Holding Clips Chapter 6...

  • Page 225: Figure 6-75 Remove The Mounting Screw

    Removing and Replacing Components Removing and Replacing the Power Supply Interface Module Step 5. Unscrew the PSI mounting screw and remove the PSI module from the server. Figure 6-75 Remove the Mounting Screw Figure 6-76 Remove the PSI Interface Module Chapter 6...

  • Page 226: Replacing The Power Supply Interface Module

    Removing and Replacing Components Removing and Replacing the Power Supply Interface Module Replacing the Power Supply Interface Module Step 1. Place the PSI module into the chassis by sliding the module retaining tab into the socket on the hard disk drive bay wall. Figure 6-77 Replacing the Power Supply Interface Module Step 2.

  • Page 227: Removing And Replacing The Hard Disk Drive (Scsi) Backplane

    Step 5. Reconnect all power and external cables. Step 6. Verify the PSI replacement and operation by using the system utilities. (See the Utilities chapter or the HP Integrity and HP 9000 iLO MP Operations Guide for additional information.) •...

  • Page 228: Figure 6-80 Disconnect Scsi Cables

    Removing and Replacing Components Removing and Replacing the Hard Disk Drive (SCSI) Backplane Step 6. Disconnect the SCSI cables and unscrew the backplane mounting screws. Figure 6-80 Disconnect SCSI Cables Figure 6-81 Remove Mounting Screws Chapter 6...

  • Page 229: Figure 6-82 Remove The Scsi Backplane

    Removing and Replacing Components Removing and Replacing the Hard Disk Drive (SCSI) Backplane Step 7. Remove the hard drive backplane by sliding it in the direction of the arrow and pulling it outward from its standoff posts. Figure 6-82 Remove the SCSI Backplane Figure 6-83 Remove the SCSI Backplane from Chassis Chapter 6...

  • Page 230: Replacing The Hard Disk Drive Scsi Backplane

    Step 7. Reconnect all power and external cables. Step 8. Verify the backplane replacement and operation by using the system utilities. (See the Utilities chapter or the HP Integrity and HP 9000 iLO MP Operations Guide for additional information.) •...

  • Page 231: Replacement Parts

    Replacement Parts This appendix provides a replacement parts list that contains the following customer self-repair part information for the server: • Manufacturing Part Number • Description • Replacement Part Number, if applicable • Exchange Part Number, if applicable This appendix addresses the following topics: •...

  • Page 232: Parts Illustrations

    Parts Illustrations Figure A-1 provides parts identification illustrations. See the replaceable parts list to identify part numbers. NOTE The parts displayed in Figure A-1 do not represent all the parts in the HP 9000 rp3410 and rp3440 servers. Figure A-1...

  • Page 233: Figure A-2 Pedestal And Rack Parts

    Replacement Parts Parts Illustrations Figure A-2 shows the pedestal and rack parts for the HP 9000 rp3410 and rp3440 servers. See the replaceable parts list to identify part numbers. Figure A-2 Pedestal and Rack Parts Appendix A...

  • Page 234: Customer Self Repair

    • Yes: Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be charged for the travel and labor costs of this service. • Optional: Parts for which customer self repair is optional.

  • Page 235: Replaceable Parts List

    Replaceable Parts List The items in this list and the corresponding item numbers are the customer self-repair units for HP 9000 rp3410 and rp3440 servers. The item numbers listed below are used with the part illustrations in order to identify the nomenclature of the part.

  • Page 236: Table A-2. Replaceable Parts List

    Replacement Parts Replaceable Parts List Table A-2 Replaceable Parts List (Continued) Part Customer Item Part Number Description Number Self Replacement Exchange Repair Power Supply Interface Module A7231-04018 SCSI Backplane A7231-66520 A7231-69520 System Board (A7136-60001); 64MB Cache A7136-67001 A7136-69001 (CPUs require PDC greater than 44.52) PCI backplane/PCI Riser A7231-66530 Display Panel...
  • Page 237 Replacement Parts Replaceable Parts List Table A-2 Replaceable Parts List (Continued) Part Customer Item Part Number Description Number Self Replacement Exchange Repair Assembly, Thin 80 mm Fan (Fan 2) A7231-04015 Assembly, Dual fan (Fan 3) A7231-04033 Assembly, Standard 80 mm Fan A7231-04017 Processors Dual 800 MHz PA-RISC CPU with 32 MB L2...
  • Page 238 Replacement Parts Replaceable Parts List Table A-2 Replaceable Parts List (Continued) Part Customer Item Part Number Description Number Self Replacement Exchange Repair Server, Assembly—Rack Latch Right A7231-04023 Server, Assembly—Rack Bezel Right A7231-04053 Server, Assembly—Rack Left Bezel with Rack A7231-04068 Latch Plastic and Metal Parts Filler, Slimline Carbon A7231-40027...
  • Page 239 Replacement Parts Replaceable Parts List Table A-2 Replaceable Parts List (Continued) Part Customer Item Part Number Description Number Self Replacement Exchange Repair Headphone 5183-9500 Power Cord U.S. Canada 125 VAC 8120-1378 Power Cord Cont. Europe 250 VAC 8120-1689 Chinese power cord, straight 8120-8376 Power Cord Japan 125 VAC 8120-4753...
  • Page 240 Replacement Parts Replaceable Parts List Appendix A...

  • Page 241: Utilities

    This appendix describes the boot console handler (BCH) utility that is part of the server. High-level information is also provided on iLO MP. For complete information on iLO MP, see the HP Integrity and HP 9000 iLO MP Operations Guide on the Web.

  • Page 242: Table B-1. Bch Main Menu, Submenus, And Commands

    Utilities Boot Console Handler Table B-1 shows the , submenus and commands. Examples are provided in “BCH Main Menu BCH Main Menu Commands and Submenus” on page 242. Table B-1 BCH Main Menu, Submenus, and Commands Submenu Description Boots from the specified path. BOot [PRI|ALT|<path>] Displays or modify a path.
  • Page 243 Utilities Boot Console Handler Example screen output of the BCH Main Menu ---- Main Menu --------------------------------------------------------------- Command Description ------- ----------- BOot [PRI|ALT|<path>] Boot from specified path * PAth [PRI|ALT|CON|KEY] [<path>] Display or modify a path SEArch [DIsplay|IPL] [<path>] Search for boot devices COnfiguration menu Displays or sets boot values INformation menu...

  • Page 244: Search Command

    Utilities Boot Console Handler Search Command The SEA (search) command automatically checks all possible boot and install devices connected to the system and displays these bootable paths. In several firmware versions, it links these paths to a shortcut (such as P0).

  • Page 245: Information Menu

    Utilities Boot Console Handler The configuration default command sets the following values: Primary boot path: 0/0/1/0.0 Alternate boot path: 0/0/2/0 Console path: 0/0/1/0.0 Keyboard path: 0/0/4/0.0 Autoboot: Autosearch: Autostart: BootTimer Information Menu menu commands enable you to view information about the configuration and state of the INformation system.
  • Page 246 Utilities Boot Console Handler Service Menu menu commands are used by service personnel to view information about the system for the SERvice purpose of system service operations. Main Menu: Enter command or menu > ser ---- Service Menu ------------------------------------------------------------ Command Description ------- -----------...

  • Page 247: Ilo Mp

    HP has used several different names to describe the management functionality embedded in their servers, including the “management processor.” In addition, HP uses the term “management processor” to refer to any embedded microprocessor that manages a system. Management processor is a descriptive term (such as “server”), and iLO is a brand name, or label (such as “Integrity”).
  • Page 248 Utilities iLO MP Appendix B...

  • Page 249: Physical And Environmental Specifications

    Physical and Environmental Specifications Table C-1 provides temperature and airflow information for minimum, typical, and maximum configurations for the HP 9000 rp3410 and rp3440 servers. It also lists the server and rack weights and dimensions. Table C-1 Physical and Environmental Specifications...
  • Page 250 Physical and Environmental Specifications Appendix C...

  • Page 251: Index

    VGA specifications setup temperature sensor troubleshooting Ethernet card LAN LEDs contacting HP event ID control panel LEDs event IDs controller event monitoring service (EMS) baseboard management external core, features I/O processor dependent hardware...
  • Page 252 See disk drive hot-pluggable disk drives Ethernet LAN installation front control panel hot-swappable iLO MP fans iLO MP card LAN power supply HP-UX locator rear panel booting status panel, remove and replace LVM maintenance mode system board shutting down troubleshooting single-user mode...
  • Page 253 Index installing DIMMS interface module, remove reallocate interface module, replace removing DIMMS unit – – replace deallocated memory rank powering off the server manually supported DIMMS using the iLO MP PC command system memory powering on the server system, installing manually MP See iLO MP using the iLO MP PC command...
  • Page 254 MP setup checklist flowchart validate server configuration shut down verify HP-UX server configuration using BCH site preparation, verifying site prep static IP address VGA graphics console, accessing assigning with ARP Ping assigning with LC command support tools manager (STM)

This manual is also suitable for:

9000 rp3440

Table of Contents