Setting The Date/Time Of The Internal Clock - Panasonic AJ-PX5000G Operating Instructions Manual

Chapter 3 Recording and Playback — Setting the date/time of the internal clock

Setting the date/time of the internal clock

The value of the time is recorded to content (clips) and affects the thumbnail playback order. Before recording, be sure to check and set the date and
time zone.
1
Set the <DISPLAY> switch to <UB>.
2
Press the <HOLD> button several times to display the time zone (time difference from Greenwich mean time) on the display
window.
For time zone display, refer to "Time code indications" (page 27) in "Description on display window".
3
Set the <TCG> switch to <SET>.
4
Set hours/minutes (h/min) and advance (no display)/delay ([−] display) from the Greenwich mean time by the cursor buttons (`/
{).
Example) Time difference 5:00 delay (New York)
Set as [05:00 −].
The time zones are always recorded as metadata together with date/time.
Set this matched to the local time by referring to the time zone table.
5
Set the <TCG> switch to <F-RUN> or <R-RUN> to apply the time zone.
6
Press the <HOLD> button several times to display [DATE] on the display window.
7
Set the <TCG> switch to <SET>.
8
Set date (Y/M/D) by the cursor buttons.
The year setting upper limit is 2037.
I: The digit to be set (flashing) moves to the right.
Y: The digit to be set (flashing) moves to the left.
`: The value of the flashing digit is incremented by one.
{: The value of the flashing digit is decremented by one.
9
Press the <HOLD> button to display [TIME] on the display window.
10
Set hours/minutes/seconds (h/min/s) by the cursor buttons.
11
Set the <TCG> switch to <F-RUN> or <R-RUN>.
When this switch is switched, the internal clock starts to operate.
r Time zone table
Time Region
difference
00:00 Greenwich
−00:30
−01:00 Azores
−01:30
−02:00 Mid-Atlantic
−02:30
−03:00 Buenos Aires
−03:30 Newfoundland
−04:00 Halifax
−04:30
−05:00 New York
−05:30
−06:00 Chicago
@ NOTE
t Be sure to make this setting before using the camera for the first time. After, do not change the setting during use.
t Thumbnail operations and menu operations on thumbnail operation section are not possible while the <TCG> switch is set to <SET>.
t After setting year/month/day in step
t To cancel settings while setting year/month/day, hours/minutes/seconds and time zone, set the <TCG> switch to <F-RUN> or <R-RUN> with the
<SET> button held down.
t Clock accuracy is a lunar inequality of approximately ±30 seconds with the power off. When accurate time is required, check and reset the time
when the power is turned on. Note that if the time is received using the built-in GPS, the time of the internal clock (local date and time) is maintained
accurately based on the time received (Greenwich mean time) and the time zone. If the time display of [DATE] and [TIME] is different from the local
time, the time zone setting may be incorrect. Check the time zone setting again ([DATE] and [TIME] do not need to be set again).
t The built-in clock runs for several years on the camera's built-in lithium cell. When the lithium cell runs low, [BACKUP BATT EMPTY] will be displayed
in the viewfinder when the camera is turned on. For details, refer to "Maintenance" (page 244).
Time Region
difference
−06:30
−07:00 Denver
−07:30
−08:00 Los Angeles
−08:30
−09:00 Alaska
−09:30 Marquesas Islands
−10:00 Hawaii
−10:30
−11:00 Midway Islands
−11:30
−12:00 Kwajalein Atoll
+00:30
8
, the internal clock will start if the <TCG> switch is set to <F-RUN> or <R-RUN>.
Time Region
difference
+01:00 Central Europe
+01:30
+02:00 Eastern Europe
+02:30
+03:00 Moscow
+03:30 Tehran
+04:00 Abu Dhabi
+04:30 Kabul
+05:00 Islamabad
+05:30 Bombay
+06:00 Dakar
+06:30 Yangon
+07:00 Bangkok
– 30 –
Time Region
difference
+07:30
+08:00 Beijing
+08:30
+09:00 Tokyo
+09:30 Darwin
+10:00 Guam
+10:30 Lord Howe Island
+11:00 Solomon Islands
+11:30 Norfolk Island
+12:00 New Zealand
+12:45 Chatham Islands
+13:00