Rec Meta Data - Panasonic AJ-PX5000G Operating Instructions Manual

[TC/UB]
Item
[UBG MODE]
[VITC UBG MODE]
[DF MODE]
[TCG SET HOLD]
[FIRST REC TC]
[TC OUT]
[TC OUTPUT REF]
[REC CHECK REGEN]

[REC META DATA]

Item
[LOAD]
[RECORD]
[USER CLIP NAME]
[CARD SERIAL]
Chapter 7 Menu Operations — Menu list
Selects the user bits mode.
[USER]: Selects the user bits value set in the display window.
[TIME]: Selects the local time. (hh, mm, ss)
[DATE]: Selects the local date and time. (YY, MM, DD, hh)
[EXT]: Records the user bits values currently input to the <TC IN> terminal.
[TCG]: The value of [TCG] is recorded as user bits.
[FRAME RATE]: Selects camera imaging information (such as frame rate).
[REGEN]: Reads the value recorded to the card and continuously records that value.
f Factory setting: [USER]
Selects the VITC user bits mode.
[USER/EXT]: When [UBG MODE] is [EXT], follows the value and when other than [EXT], records the user
value set in [USER].
[TIME]: Selects the local time. (hh, mm, ss)
[DATE]: Selects the local date and time. (YY, MM, DD, hh)
[TCG]: The value of time code generator is recorded as user bits.
[FRAME RATE]: Selects camera imaging information (such as frame rate).
[REGEN]: Reads the value recorded to the card and continuously records that value.
f Factory setting: [USER/EXT]
This item is not displayed in 720P mode, and the setting of [FRAME RATE] is used.
Sets drop frame mode/non-drop frame mode of the [CTL] and [TCG].
[DF]: Uses the drop frame mode.
[NDF]: Uses the non-drop frame mode.
f Factory setting: [DF]
This item is not displayed when the system frequency is 50 Hz.
If the internal time code generator is set with the <TCG> switch before turning power off, switch [ON]/[OFF]
for the function that recording starts from the preset value when turning on the power to start recording.
[ON], [OFF]
f Factory setting: [OFF]
Selects whether to regenerate the time code to the value on the P2 card at the first recording after power is
turned on, a P2 card is inserted, or the P2 card targeted for recording is switched.
[PRESET]: Uses the internal time code of the camera.
[REGEN]: Regenerates time code based on the clip with the newest date and time among the clips
recorded to the P2 card targeted for recording.
f Factory setting: [REGEN]
Make sure the date and time are correctly set. For the setting method, refer to "Setting the date/time of the
internal clock" (page 30).
Selects the time code output to the <TC OUT> terminal.
[TCG]: Outputs the time code generator value at all times.
[TCG/TCR]: Outputs the time code generator value during recording and the time code reader value
during playback.
f Factory setting: [TCG]
Sets the output delay of time code output from the <TC OUT> terminal.
For details, refer to "Externally locking the time code" (page 77).
[TC IN]: Matches to external time code input.
[VIDEO OUT]: Matches to output images.
f Factory setting: [TC IN]
Selects whether to regenerate to the time code last recorded to the P2 card at the next recording when the
<RET> button that assigns recording check function or the <USER> button is pressed.
[ON]: Regenerates.
[OFF]: Does not regenerate.
f Factory setting: [OFF]
Loads the metadata upload file saved to the SD memory card.
Sets whether to add loaded metadata at a recording.
[ON]: Adds metadata.
[OFF]: Does not add metadata.
f Factory setting: [OFF]
Sets data to be recorded to [USER CLIP NAME].
When [RECORD] is [ON]:
[TYPE1]: Records setting values of the loaded data.
[TYPE2]: Records the loaded data and counter value.
f Factory setting: [TYPE1]
When [RECORD] is [OFF]:
[TYPE1]: Records the same value as [GLOBAL CLIP ID].
[TYPE2]: Records the same value as [CLIP NAME].
f Factory setting: [TYPE1]
Enables/disables the function for storing the text memo with the serial number or the type of card as
metadata.
[ON], [OFF]
f Factory setting: [OFF]
– 175 –
Description of settings
Description of settings