Panasonic AJ-PX5000G Operating Instructions Manual page 180

Item
[LVL CONTROL CH3(CH1)]
[LVL CONTROL CH4(CH2)]
[MIC LOWCUT CH1]
[MIC LOWCUT CH2]
[MIC LOWCUT CH3]
[MIC LOWCUT CH4]
[LIMITER CH1]
[LIMITER CH2]
[LIMITER CH3]
[LIMITER CH4]
[TEST TONE]
[FRONT MIC POWER]
[REAR MIC POWER]
[MONITOR SELECT]
[FRONT MIC LEVEL]
[REAR MIC CH1/3 LVL]
Chapter 7 Menu Operations — Menu list
Can be manually adjusted with this item when automatic level adjustment of audio CH3 (CH1) is [OFF].
[0]...[100]
f Factory setting: [70]
The channel is replaced when [CH3/4] is selected in [VR SELECT]. Setting values are inherited between
replaced channels.
Can be manually adjusted with this item when automatic level adjustment of audio CH4 (CH2) is [OFF].
[0]...[100]
f Factory setting: [70]
The channel is replaced when [CH3/4] is selected in [VR SELECT]. Setting values are inherited between
replaced channels.
Selects the microphone lowcut filter for input channel 1.
[FRONT]: Works when the front microphone is selected.
[W.L.]: Enabled only when wireless microphone receiver is selected.
[REAR]: Enabled only when the rear microphone is selected.
[OFF]: The microphone lowcut filter does not work for any input.
f Factory setting: [OFF]
Selects the microphone lowcut filter for input channel 2.
[FRONT]: Works when the front microphone is selected.
[W.L.]: Enabled only when wireless microphone receiver is selected.
[REAR]: Enabled only when the rear microphone is selected.
[OFF]: The microphone lowcut filter does not work for any input.
f Factory setting: [OFF]
Selects the microphone lowcut filter for input channel 3.
[FRONT]: Works when the front microphone is selected.
[W.L.]: Enabled only when wireless microphone receiver is selected.
[REAR]: Enabled only when the rear microphone is selected.
[OFF]: The microphone lowcut filter does not work for any input.
f Factory setting: [OFF]
Selects the microphone lowcut filter for input channel 4.
[FRONT]: Works when the front microphone is selected.
[W.L.]: Enabled only when wireless microphone receiver is selected.
[REAR]: Enabled only when the rear microphone is selected.
[OFF]: The microphone lowcut filter does not work for any input.
f Factory setting: [OFF]
Selects the channel 1 limiter.
Disabled when automatic adjustment of recording levels is selected.
[ON], [OFF]
f Factory setting: [OFF]
Selects the channel 2 limiter.
Disabled when automatic adjustment of recording levels is selected.
[ON], [OFF]
f Factory setting: [OFF]
Selects the channel 3 limiter.
Disabled when automatic adjustment of recording levels is selected.
[ON], [OFF]
f Factory setting: [OFF]
Selects the channel 4 limiter.
Disabled when automatic adjustment of recording levels is selected.
[ON], [OFF]
f Factory setting: [OFF]
Selects test signals.
[NORMAL]: Outputs test tones to all channels if the <OUTPUT> switch is <BARS>, and <CH1> on the
<AUDIO IN> switch is set to <FRONT>.
[ALWAYS]: Outputs test tones to all channels at all times when the <OUTPUT> switch is <BARS>.
[CHSEL]: When the <OUTPUT> switch is <BARS>, outputs test tones to the channel for which <CH1> or
<CH2> on the <AUDIO IN> switch is set to <FRONT>. The test tones are not output to CH3 and CH4.
[OFF]: Does not output the test tone.
f Factory setting: [NORMAL]
Sets the phantom power of the front microphone.
[ON], [OFF]
f Factory setting: [ON]
Sets the phantom power of the rear microphone.
Phantom power is not output when [OFF] is selected, even if the <REAR AUDIO CH1> and <REAR AUDIO
CH2> switches are set to <+48V>.
[ON], [OFF]
f Factory setting: [ON]
Selects the signal method to output to the monitor when the <MONITOR SELECT> switch is set to <ST>
(stereo).
[STEREO], [MIX]
f Factory setting: [STEREO]
Selects the front microphone input level.
[−40dB], [−50dB]
f Factory setting: [−40dB]
Selects the rear microphone input level.
[−50dB], [−60dB]
f Factory setting: [−60dB]
– 180 –
Description of settings