Panasonic AJ-PX5000G Operating Instructions Manual page 86

Chapter 4 Adjustments and Settings for Recording — Viewfinder status display
[A]
The <WHITE BAL> switch is set to <A>.
[B] The <WHITE BAL> switch is set to <B>.
[P] The <WHITE BAL> switch is set to <PRST>.
[T] The switch is set to [ATW]. Note, however, that this flashes when brightness and color are outside the operation range.
14 Dynamic range stretcher (DRS) function display
[DRS] Displayed when the image level in high-brightness areas is compressed and the dynamic range is stretched.
15 Incremental gain display
Displays the value when incremental gain is functioning.
[6 ↑]/[10 ↑]/[12↑]/[15↑]/[20↑]/[24↑]/[28↑]/[34↑]
16 Gain display
Displays the gain value of the image amplifier configured.
Displays the current gain value.
[**dB]
[AGC]
Displayed when auto gain control is active.
17 System information and warning
[SYSTEM ERROR Displayed when an abnormality in internal microcomputer communication or the reference signal has occurred. From here on,
E-**] recording and playback are not possible. The error code is displayed on **. For details, refer to "Error code" (page 247).
[TURN POWER OFF Displayed when operation is no longer possible after P2 card is removed during accessing of the P2 card, for example, during
E-**] recording/playback or formatting. The error code is displayed on **.
[TEMPORARY PAUSE Displayed when the reference signal is disrupted and recording is suspended during generator lock input, etc.
IRREGULAR SIG]
[EOM] Displayed when there is no space remaining on the P2 card.
[BOS] Displayed when the playback position is at the beginning of all clips.
[EOS]
Displayed when the playback position is at the end of all clips.
Displayed when recording to the P2 card is not possible, for example, immediately after power is turned on or the P2 card is
[CANNOT REC] inserted. Detailed information of the P2 card can be checked in the mode check [FUNCTION] screen. For details, refer to "Mode
check display" (page 91).
[CANNOT PLAY] Displayed when playback is not possible, for example, when there are no clips on the P2 card or the P2 card is not inserted.
[TEXT MEMO] Displayed when a text memo is recorded.
[TEXT MEMO INVALID] Displayed when a text memo could not be recorded.
[MARK ON/OFF] Displayed when shot marks are added or deleted. For details on shot marks, refer to "Shot mark recording function" (page 42).
[SHOT MARK INVALID] Displayed when shot marks cannot be added.
[UPDATING]
Displayed when playback operation is not accepted during updating of the clip information for playback.
Displayed when the USB device mode is set. Flashes during migration through modes, and after migration through modes
[USB DEVICE] is completed, [CONNECTED] is displayed when communication is possible and [DISCONNECTED] is displayed when
communication is not possible.
Displayed when the USB storage mode is set. Flashes during migration through modes, and from then on, [CONNECTED]
[USB STORAGE] is displayed when the external hard disk is recognized successfully and [DISCONNECTED] is displayed when it cannot be
recognized.
[THUMBNAIL OPEN] Displayed during thumbnail operation.
[TC REGEN] Displayed when the <RET> button on the lens is pressed to regenerate to the time code of the last recorded clip to the P2 card.
Lights up when the <USER> button assigned with [SLOT SEL] is pressed to start the process of switching the recording slot of
[SLOT SELECT]
the P2 card.
Displayed when the <USER> button assigned with [SLOT SEL] is pressed and switching processing of the recording slot on the
[SLOT SEL INVALID]
P2 card is not possible.
Displayed when recording cannot be paused, if recording resumes during recording completion process. This warning disappears
[REC PAUSE INVALID]
when recording completion process ends, and recording can be paused.
Displayed when the transmission of the streaming video from the camera is started by pressing the <USER> button assigned as
[START ON]
[STREAMING START].
Displayed when the transmission of the streaming video from the camera is stopped by pressing the <USER> button assigned as
[START OFF]
[STREAMING START].
Displayed when the status of the streaming video from the camera cannot be switched by pressing the <USER> button assigned
[START INVALID]
as [STREAMING START].
For details on warnings, refer to "Warning information display" (page 247).
18 Time code display
[TCG 12:59:59:20] Displays the time code generator value.
[TCR 12:59:59:20] Displays the time code reader value.
[VUBG AB CD EF 00] Displays the user's bit generator value.
([UBG AB CD EF 00])
[VUBR 12 34 56 78] Indicates the user's bit reader value.
([UBR 12 34 56 78])
[CTL −1:59:59:20] Displays the CTL counter value.
19 Audio input line and level meter display
Displays the selected channel and its audio level.
[----r----+]
– 86 –