Panasonic AJ-PX5000G Operating Instructions Manual page 87

Chapter 4 Adjustments and Settings for Recording — Viewfinder status display
[F] Displayed when the <AUDIO IN> switch is <FRONT>.
[W] Displayed when the <AUDIO IN> switch is <W.L.>.
[R] Displayed when the <AUDIO IN> switch is <REAR>.
20 Iris override display
Displays the compensation level when the iris overwrite is functioning.
Aperture opens by about 1.
[++]
[+] Aperture opens by about 0.5.
Aperture closes by about 1.
[−−]
[−] Aperture closes by about 0.5.
(No display) Reference state.
21 Super iris display
Displayed when super iris is active.
22 Iris, F value
[NC] Displayed when the lens cable is not connected.
[OPEN] Displayed when the lens aperture is open.
[F1.7] to [F16] Displays the lens aperture value.
[CLOSE] Displayed when the lens aperture is closed.
f Displayed when a lens with an aperture value display function is used. Also, flashes when the iris override is variable.
23 Super black display
Displayed when super black is active.
24 Zoom display
Displays the zoom amount. Note, however, that this item is not displayed in the case of lenses without a zoom position return
[Z00] to [Z99]
even if it is set to be displayed.
When a serial lens is connected, the display unit can be changed in the main menu → [VF] → [VF INDICATOR] → [ZOOM/
[Z**.*mm]
FOCUS].
25 Focus control information
Displays the focus control information with [99] to [00]. When a lens other than a serial lens is connected, the focus control information is not
displayed. When a serial lens is connected, the display unit can be changed in the main menu → [VF] → [VF INDICATOR] → [ZOOM/FOCUS].
26 Information display such as interval recording/pre-recording
[i] Displayed before recording starts and after recording ends during interval recording.
[i-REC] (flashing) Displayed during recording in interval recording.
[i-REC] (flashing) During interval recording standby, displays the standby time until the next recording.
[**h**m/**s]
Displayed after recording is stopped and until recording of video/audio to P2 card completely stops. Do not remove the P2 card
[P-REC] (flashing) or turn the power off until the flashing indication completely goes out.
f When the pre-recording function is set to [OFF], [REC] flashes.
Illuminated if the <MARKER SEL>/<MODE CHECK/MENU CANCEL> switch is pushed towards the <MCK/MCL> side when the
[P-REC *s/OFF]
pre-recording function is set to [ON]. The status is displayed when the <USER> button where [PRE REC] is assigned is pressed
(illuminated)
to switch to the pre-recording mode.
[1-CLIP] Displayed when [ONE CLIP REC] is [ON], and a new clip is going to be recorded.
Displayed when [ONE CLIP REC] is [ON], and recording can be linked to the previous clip.
[1*CLIP] f If the previous clip no longer exists due to removal of the P2 card or deletion of the clip, the next recording will start as a new
Displayed when recording of a new clip is started in [ONE CLIP REC].
[START 1*CLIP]
[END 1-CLIP] Displayed when linking of clips is ended in [ONE CLIP REC].
27 Gamma mode display
Displays the gamma mode currently selected by [GAMMA MODE SEL] in the main menu → [PAINT] → [GAMMA].
[HD]/[SD]/[FLK1]/[FLK2]/[FLK3]/[FREC]/[VREC]
28 Lock status display of auto tracking white balance
Displayed when the <USER> button where [ATW LOCK] is assigned is pressed and the color temperature is fixed while auto tracking white balance
is active.
29 Type of marker
Displays the type of currently displayed marker.
[MKR:A/B/OFF]
30 Network information display
[WLAN] Displayed when the wireless LAN is operating properly.
Displayed when the wireless LAN is not operating properly.
!
[WLAN ]
[LAN] Displayed when the wired LAN is operating properly.
Displayed when the wired LAN is not operating properly.
!
[LAN ]
31 Streaming setting status display
Displays the setting status of the streaming function.
clip. In this case, the display may remain as [1*CLIP].
– 87 –