Configuring The Programmable Timer - Kenwood TS-990S Instruction Manual

[ TIMER/SET ]
[F1] [F7]
[ ESC ]

CONFIGURING THE PROGRAMMABLE TIMER

Time to turn the transceiver power ( ) ON or OFF or the
timed task for Programmable Timer can be configured.
1 Press and hold [TIMER/SET] to open the Timer
screen.
2 Press [ ] (F2) or [
"Programmable Timer".
3 Press [EDIT] (F4) to open the Programmable Timer
screen.
Contents Index
4 Use the function keys and the MULTI/CH control to
[MULTI/CH]
] (F3) to select
5 Press [OK] (F6).
6 Press [OK] (F6).
7 Press [ESC] to exit.
8 If the timer except for the power-off timer is active,
configure the Programmable Timer.
Menu Item Method of Configuration
Press [ON/OFF] (F4) to toggle the timed task by a
timer between active and inactive.
Timer
Selecting "ON" enables the timer. Selecting "OFF"
disables the timer.
Press [ON/OFF] (F4) to toggle the timed repeat by a
timer between active and inactive.
Repeat Selecting "ON" allow you to repeat the timed task as
configured. Selecting "OFF" does not allow you to
repeat the timed task as configured.
Press [ ] (F2), [
(F4) to select and to enable or disable the day of the
Day of the
week when the timed task by a timer will be executed.
Week
The timer will be used with the selected day of the
week.
Press [MODE] (F4) to select the timer task.
Power-on: The transceiver turns ON at the time
configured for Power-on. If "Power-on" is selected,
"--:--" appears as time for Power Off, and you cannot
configure.
Power-off: The transceiver power ( ) turns OFF at the
time configured for Power-off. If "Power-off" is selected,
"--:--" appears as time for Power On, and you cannot
Mode
configure.
Both: The transceiver power ( ) turns ON at the
time configured for Power-on and OFF at the time
configured for Power-off.
Record: The transceiver stores the received audio onto
a USB flash drive during the time between the time
configured for Power-on and the time configured for
Power-off.
Pressing [-] (F4), [+] (F5) or the numeric and band
selection keypad, or rotating the MULTI/CH control can
Power-on/ configure the time to turn the transceiver power ( ) ON
Power-off and OFF.
The time can be configured in the range of "00:00" to
"23:59".
Press [COPY] (F5) to copy the frequency and the
operating band information for the main band and sub
band when the transceiver is turned ON by a timer.
Placing the main band and sub band in VFO mode and
then pressing [COPY] (F5) can copy the frequency and
the operating band information.
Even if you can change the configuration for main
Main Band/ band Even if the main band or sub band is highlighted,
Sub band [ ] (F2), [
keypad can be pressed, and the Tuning (M) and
MULTI/CH control can be rotated to change the
frequency displayed on the upper side of the Program
Timer screen. To change the configurations for
frequency and mode for the main band and sub band
when the transceiver starts up, press [COPY] (F5)
each time when the frequency is changed.
• The "TIMER" LED lights green, the timed task by a timer
will be enabled. A message notifying you of the end of the
configuration appears.
• Pressing [CANCEL] (F7) clears the entered parameter and
reverts to the Clock screen.
Pressing [CANCEL] (F7) clears the entered parameter and
reverts to the Clock screen.
CLOCK DISPLAY AND TIMER 15
] (F3), or [ ]
] (F3) and the numeric
15-5