Kenwood TS-990S Instruction Manual page 12

TABLE OF CONTENTS
USING THE USB KEYBOARD TO TRANSMIT A TEXT
STRING ................................................................................ 5-56
UTILIZING AN PSK MESSAGE MEMORY .......................... 5-57
STORING MESSAGES ..................................................... 5-57
CONFIGURATION FOR PSK ENCODING AND DECODING .....
5-59
DISPLAYING THE TIME STAMP ....................................... 5-59
SELECTING THE TIMESTAMP TIME ................................ 5-60
PSK-RELATED CONFIGURATION ...................................... 5-60
CONFIGURING THE PSK TONE FREQUENCY ............... 5-60
USING A PC TO COMMUNICATE IN PSK MODE ............ 5-60
6 REJECTING INTERFERENCE
ATTENUATOR (ATT) .............................................................. 6-1
PRESELECTOR ..................................................................... 6-1
DSP FILTER ........................................................................... 6-2
CHANGING THE IF FILTER BANDWIDTH
CHARACTERISTICS ............................................................. 6-2
SWITCHING THE RX FITER CONFIGURATIONS ............. 6-2
SELECTING THE ROOFING FILTER .................................. 6-3
SWITCHING THE IF FILTER TYPE...................................... 6-4
CHANGING THE AF FILTER TYPE ....................................... 6-5
CHANGING THE CUTOFF FREQUENCIES (LOW AND
HIGH FREQUENCY) TO ADJUST THE PASSBAND WIDTH
CHARACTERISTICS ............................................................. 6-6
CHANGING THE PASSBAND WIDTH AND SHIFT TO ADJUST
PASSBAND CHARACTERISTICS ......................................... 6-7
ACTIVATING AUDIO PEAK FILTER FOR USE IN CW MODE ....
6-7
CHANGING THE PASSBAND CHARACTERISTICS OF THE
AUDIO PEAK FILTER (APF) ................................................. 6-8
SHIFTING THE PASS BAND OF THE AUDIO PEAK FILTER .....
6-8
AUDIO PEAK FILTER WHILE IN FSK MODE ....................... 6-9
NOISE BLANKER .................................................................. 6-9
MANUAL NOTCH FILTER (SSB, CW, FSK, AND PSK) ...... 6-10
AUTO NOTCH FILTER (SSB) .............................................. 6-11
BAND ELIMINATION FILTER .............................................. 6-12
NOISE REDUCTION ............................................................ 6-13
BEAT CANCELLER (SSB, AM AND FM) ............................ 6-14
DSP MONITOR .................................................................... 6-15
ASSIGNING THE DSP MONITOR TO THE PF KEY .......... 6-15
7 BANDSCOPE
BANDSCOPE ......................................................................... 7-1
DISPLAYING THE BANDSCOPE ........................................ 7-1
WATERFALL ....................................................................... 7-1
ADJUSTING THE REFERENCE LEVEL ............................. 7-1
TOGGLING THE CENTER MODE AND FIXED MODE ....... 7-2
CONFIGURING THE LOWER AND UPPER LIMIT ............. 7-5
DISPLAYING THE MARKERS ............................................. 7-6
DISPLAYING THE MAXIMUM WAVEFORM VALUE ............ 7-7
PAUSING THE WAVEFORM DISPLAY ................................ 7-7
CHANGING THE ATTENUATOR FOR THE BANDSCOPE ... 7-8
DISPLAYING THE TRANSMISSION SIGNAL WAVEFORM . 7-8
8 AUDIO SCOPE
DISPLAYING THE AUDIO SCOPE AND OSCILLOSCOPE .. 8-1
CHANGING THE LEVEL OF THE OSCILLOSCOPE........... 8-2
CHANGING THE SWEEP TIME .......................................... 8-3
PAUSING THE AUDIO SCOPE AND OSCILLOSCOPE ...... 8-3
9 TRANSMIT FUNCTIONS
SELECTING THE AUDIO LINE FOR TRANSMISSION ........ 9-1
SELECTING THE AUDIO SOURCE FOR TRANSMISSION BY
SEND/PTT .............................................................................. 9-1
VOX (VOICE-OPERATED TRANSMIT) .................................. 9-2
SWITCHING VOX (VOICE) ON OR OFF ............................. 9-2
X
ADJUSTING THE VOX GAIN ............................................... 9-3
ADJUSTING THE VOX DELAY TIME ................................... 9-3
ADJUSTING THE ANTI VOX GAIN LEVEL .......................... 9-4
DELAYING THE AUDIO SIGNAL ......................................... 9-5
TX MONITOR ......................................................................... 9-5
ADJUSTING THE TX MONITOR LEVEL ............................. 9-5
SPEECH PROCESSOR ......................................................... 9-6
TRANSMIT FILTER ................................................................ 9-8
SELECTING A TX FILTER ................................................... 9-8
CHANGING THE NUMBER OF AVAILABLE TX FILTERS ... 9-8
CHANGING THE BANDWIDTH OF THE TX FILTER ........... 9-9
TX DSP EQUALIZER ............................................................. 9-9
SWITCHING THE TX DSP EQUALIZER ON OR OFF ......... 9-9
ADJUSTING THE TX DSP EQUALIZER ............................ 9-10
DISPLAYING THE SUBSCOPE DURING TX ...................... 9-13
TX TUNING .......................................................................... 9-14
ADJUSTING THE TRANSMIT POWER FOR TX TUNING . 9-14
TIME-OUT TIMER (TOT) ..................................................... 9-14
10 MEMORY CHANNELS
MEMORY CHANNEL ........................................................... 10-1
DISPLAYING THE MEMORY CHANNEL LIST .................. 10-1
MEMORY CHANNEL MODE ............................................... 10-4
SELECTING A MEMORY CHANNEL ................................ 10-5
TEMPORARILY CHANGING THE OPERATING DATA ....... 10-5
TEMPORARILY CHANGING FREQUENCY ...................... 10-5
COPYING OPERATING DATA FROM THE MEMORY
CHANNEL ............................................................................ 10-6
MEMORY SHIFT (MEMORY TO VFO) .............................. 10-6
CONFIGURING THE PROGRAM SCAN FREQUENCY RANGE
10-7
CLEARING THE MEMORY CHANNEL ............................... 10-7
CONFIGURING NAMES FOR MEMORY CHANNELS ........ 10-7
QUICK MEMORY ................................................................. 10-8
QUICK MEMORY CHANNELS ............................................ 10-8
CONFIGURING IN QUICK MEMORY .................................. 10-8
RECALLING QUICK MEMORY CHANNELS ...................... 10-8
CONFIGURING THE NUMBER OF QUICK MEMORY
CHANNELS .......................................................................... 10-9
CLEARING QUICK MEMORY CHANNELS ........................ 10-9
MEMORY SHIFT (QUICK MEMORY TO VFO) .................. 10-9
11 SCAN
PROGRAM SCAN ................................................................ 11-1
STARTING THE PROGRAM SCAN (VFO SCAN) ............. 11-1
CHANGING THE SCAN SPEED ....................................... 11-2
SCAN HOLD ..................................................................... 11-2
PROGRAM SLOW SCAN ................................................. 11-3
MEMORY SCAN................................................................... 11-4
STARTING THE SCAN ...................................................... 11-4
LOCKING OUT A MEMORY CHANNEL ........................... 11-5
QUICK MEMORY SCAN ...................................................... 11-6
RESUMING THE SCANNING .............................................. 11-6
12 ABOUT THE USB FLASH DRIVE
ABOUT THE USB FLASH DRIVE ........................................ 12-1
FORMATTING A USB FLASH DRIVE ................................. 12-1
SAFELY REMOVING THE USB FLASH DRIVE .................. 12-1
SAVING A FILE IN USB FLASH DRIVE .............................. 12-2
READING A FILE FROM USB FLASH DRIVE .................... 12-2
DELETING A FILE FROM USB FLASH DRIVE .................. 12-3
CHANGING A FILE NAME IN THE USB FLASH DRIVE .... 12-4
13 VOICE MESSAGE AND AUDIO FILE
RECORDING AND PLAYING VOICE MESSAGE ................ 13-1
RECORDING A VOICE MESSAGE ................................... 13-1
NAMING A VOICE MESSAGE .......................................... 13-2
PLAYING A VOICE MESSAGE .......................................... 13-2
Index