Switching The Band While In Swl Mode; Audio Source Lines For Tx Audio - Kenwood TS-990S Instruction Manual

In SWL mode, the following functions are restricted.
Function
Transmit
Transmission of a voice message
Encoding and decoding the RTTY/
PSK message
Transmission of a CW message
Transmit Power Limiter
Changing Meter
Changing the TX filter type
Transverter activation
FM tone
Antenna tuning
Configurations associated with RX
equalizer
Configurations associated with TX
equalizer
Meter display

SWITCHING THE BAND WHILE IN SWL MODE

To change the broadcast band while the transceiver is
in SWL mode, you can press [BAND
[BAND ] (F). "nn m" appears while the frequency
is within the range of the band. The following table shows
broadcast bands that are preset in the transceiver.
Broadcast and Lower limit
Meter Band [kHz]
LW 145
MW 525
120 m 2300
90 m 3200
60 m 4750
49 m 5900
41 m 7200
31 m 9400
25 m 11600
21 m 13570
19 m 15100
16 m 17480
15 m 18900
13 m 21450
11 m 25670
The band divisions configured in the transceiver in SWL
mode may differ from general definitions of meter bands.
In SWL mode, you can operate the transceiver as follows:
• RX Play: Pressing [RX PLAY] displays the list of the stored
audio files.
• Scan: Pressing [SCAN] starts a scan. When the scan stops
at a frequency, the transceiver starts receiving signals on the
frequency.
• Referring to the memory channel list: Pressing [M.LIST]
displays the memory channel list.
Contents Index
Status
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Can toggle between active and
inactive. However, the status, either
active or inactive, does not appear.
Disabled
Dedicated to the main band.
] (F) or
Upper limit
Default [kHz] and Mode
[kHz]
285 145
1705 525
2495 2300
3400 3200
5060 4750
6200 5900
7450 7200
9900 9400
12100 11600
13870 13570
15800 15100
17900 17480
19020 18900
21850 21450
26100 25670

AUDIO SOURCE LINES FOR TX AUDIO

The transceiver incorporates audio source lines, such as
microphone, OPTICAL, USB audio, and ACC 2 input
lines, for a variety of audio signals. You can select one or
more of the audio source lines depending on the mode or
selected method for transmission.
[ESC] [F1] [F7]
1 Press and hold [DATA/SEL] to open the Modulation
Source screen.
In the list that appears on this screen, the "lines" represent
methods to select the transmit mode and "rows" represents
the audio input source.
2 Press [
desired method for transmit mode selection.
3 Press [
for the audio source.
AM
4 Press [ON/OFF] (F6) to toggle the selected audio
source between On and Off.
• You can also rotate the MULTI/CH control to select "On" or
"Off" for the audio source line selected at step 3. If "On" is
configured, audio entered from the selected audio source
will be transmitted, and if "Off" is configured, the audio
from the selected audio source will be muted, and no audio
signal will be transmitted.
• Pressing and holding [(RESET)] (F1) resets the
configurations for the audio source for each transmitting
method to the defaults.
5 Press [
ASSISTING YOUR SMOOTH QSO 5
[MULTI/CH]
[DATA]
] (F2) or [ ] (F3) and select the
] (F3) or [ ] (F5) to select the row
] (F1).
5-11